NAVY MIL-DTL-82876 A (2)-2001 CATAPULT AIRCRAFT EJECTION SEAT CKU-5B A ASSEMBLY《CKU-5B A组飞机弹射座椅弹射器》.pdf

《NAVY MIL-DTL-82876 A (2)-2001 CATAPULT AIRCRAFT EJECTION SEAT CKU-5B A ASSEMBLY《CKU-5B A组飞机弹射座椅弹射器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-82876 A (2)-2001 CATAPULT AIRCRAFT EJECTION SEAT CKU-5B A ASSEMBLY《CKU-5B A组飞机弹射座椅弹射器》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、1 of 2INCH-POUNDMIL-DTL-82876A(OS)AMENDMENT 2 14 June 2001 SUPERSEDINGAMENDMENT 123 October 2000 DETAIL SPECIFICATION CATAPULT, AIRCRAFT EJECTION SEAT, CKU-5B/A ASSEMBLY This amendment forms a part of MIL-DTL-82876A, dated 4 August1995, and is approved for use within theNaval Sea Systems Command, De

2、partment of the Navy and is available for use by all departments andagencies of the Department of Defense. PAGE 2* 2.2.1, under Specifications, Military: Insert the following;“MIL-DTL-82683 Propellant, Solid“* Under Standards, Military: Delete in its entirety; “MIL-STD-453 Inspection, Radiographic“

3、PAGE 3* 2.3, under ASTM, in front of “E 165“ and “E 1444“, Add “ASTM “ * Insert the following: “ASTM E 1742 Standard Practice for Radiographic Examination (DoD adopted)“ * In the request-for-copies parentheses: Change address from “for Testing and Materials, 1916 Race Street,Philadelphia, PA 19103.)

4、“ to “for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)“ PAGE 4* 3.3.1, second line: Delete “grain (cartridge case and grain assembly per Drawing 11740607). For“ and insert“grain (Propellant grain per Drawing 5184356). For“. * 3.4.1.1, Insert the following; “e. The

5、 thrust-time curve shall exhibit a shape that compares well with the established (orrepresentative) curve for the unit.“ AMSC N/A FSC 1377 Distribution Statement A: Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without li

6、cense from IHS-,-,-MIL-DTL-82876A(OS) AMENDMENT 2 2PAGE 8* 4.3, third line, Change from “two cartridge case and grain assemblies“ to “two cartridge propellant grains“.PAGE 10* 4.3.3, first line, Change from “cured propellant“ to “cured rocket motor propellant“.* Fifth line, Change from “rocket prope

7、llant sample“ to “rocket motor propellant sample“. Fifth line, Delete “and to MIL-P-82562 for the“ and insert “and to MIL-DTL-82683 for the“.* 4.3.4, first line, Change from “two cartridge case and grain assemblies“ to “two cartridge propellant grains“.PAGE 13* 4.4.4.1, second line, Change from “maj

8、or defects specified“ to “major defects as specified“. PAGE 14* 4.4.6.1, second line, Change from “MIL-STD-453, radiographic quality level 1“ to “ASTM E 1742,radiographic quality level 2-1T“. * 4.4.6.4, second line, Change from “MIL-STD-453, radiographic quality level 1“ to “ASTM E 1742,radiographic

9、 quality level 2-1T“. PAGE 19* 6.11, second line, Change from “9 years“ to “10 years“. 6.12, first line, Delete “of 8 years of 8 years“ and substitute “of 9 years of 9 years“.Note: The margins of this amendment are marked with asterisks to indicate where changes from theprevious amendment were made.

10、 This was done as a convenience only and the Government assumes noliability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluatethe requirements of this document based on the entire content irrespective of the marginal notations andrelationship to the last previous amendment. . Preparing activity: Navy OS (Project 1377-0160) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-