NAVY MIL-DTL-24560 A-1999 LIGHTS AND GLASSWARE FOR NAVIGATION SIGNAL AND WARNING NAVAL SHIPBOARD USE GENERAL SPECIFICATION FOR《海军军舰上信号和警告航海电灯和玻璃类器具总说明书》.pdf

《NAVY MIL-DTL-24560 A-1999 LIGHTS AND GLASSWARE FOR NAVIGATION SIGNAL AND WARNING NAVAL SHIPBOARD USE GENERAL SPECIFICATION FOR《海军军舰上信号和警告航海电灯和玻璃类器具总说明书》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24560 A-1999 LIGHTS AND GLASSWARE FOR NAVIGATION SIGNAL AND WARNING NAVAL SHIPBOARD USE GENERAL SPECIFICATION FOR《海军军舰上信号和警告航海电灯和玻璃类器具总说明书》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMIL-DTL-24560A(SH)5 February 1999SUPERSEDINGMIL-L-24560(SH)10 September 1979DETAIL SPECIFICATIONLIGHTS AND GLASSWARE FOR NAVIGATION, SIGNAL, AND WARNING,NAVAL SHIPBOARD USE, GENERAL SPECIFICATION FORThis specification is approved f or use by the Naval Sea Systems Command,Department of the

2、Navy, and is available for use by all Departments andAgencies of the Department of Defense.l. SCOPE1.1 Scope . This specification covers light assemblies and associatedglassware used for navigation, signal, and warning purposes on Naval ships.1.2 Classification . Light assemblies and glassware cover

3、ed by thisspecification will be of the following types and classes, as specified (see6.2):Light Assemblies :TYPE I - Splashproof .TYPE II - Submersible .Glassware :CLASS l - Fresnel type lens .CLASS 2 - Globe, roundel , and lens .CLASS 3 - Fresnel globe .2. APPLICABLE DOCUMENTS2.1 General . The docu

4、ments listed in this section are specified insections 3 and 4 of this specification. This section does not includedocuments cited in other sections of this specification or recommended foradditional information or as examples. While every effort has been made toensure the completeness of this list,

5、document users are cautioned that theymust meet all specified requirements documents cited in sections 3 and 4 ofthis specification, whether or not they are listed.Beneficial comments (recommendations, additions, deletions) and any pertinentdata which may be of use in improving this document should

6、be addressed to:Commander, Naval Sea Systems Command, SEA 03Q, 2531 Jefferson Davis Highway,Arlington, VA 22242-5160 by using the Standardization Document ImprovementProposal (DD Form 1426) appearing at the end of this document or by letter.AMSC N/A FSC 6220DISTRIBUTION STATEMENT A . Approved for pu

7、blic release; distribution isunlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24560A(SH)22.2 Government documents .2.2.1 Specifications , standards, and handbooks . The followingspecifications , standards , and handbooks form a part

8、of this document to theextent specified herein. Unless otherwise specified, the issues of thesedocuments are those listed in the issue of the Department of Defense Index ofSpecifications ( DoDISS) and supplement thereto, cited in the solicitation (see6.2).SPECIFICATIONSDEPARTMENT OF DEFENSEMIL-S-90l

9、 - Shock Tests, H.I. (High-Impact) ShipboardMachinery, Equipment , and Systems,Requirements for.MIL-E-917 - Electric Power Equipment Basic Requirements .MIL-S-8660 - Silicone Compound, NATO Code Number S-736.MIL-I-l72l4 - Indicator Permeability, Low- Mu (Go-No-Go).MIL-T-2236l - Thread Compound, Anti

10、seize, Zinc Dust-Petrolatum.(See supplement l for list of specification sheets.)STANDARDSDEPARTMENT OF DEFENSEMIL-STD-l08 - Definitions of and Basic Requirements forEnclosures for Electric and ElectronicEquipment.MIL-STD-167-l - Mechanical Vibrations of Shipboard Equipment(Type I - Environmental and

11、 Type II -Internally Excited).MIL-STD-202 - Test Methods for Electronic and ElectricalComponent Parts.MIL-STD-278 - Welding and CastingStandard.MIL-STD-2175 - Castings, Classification and Inspection of.(Unless otherwise indicated, copies of the above specifications,standards, and handbooks are avail

12、able from the Defense Automated PrintingService ( DAPs), 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)2.3 Non-Government publications . The following documents form a partof this document to the extent specified herein. Unless otherwise specified,the issues of the documents which ar

13、e DoD adopted are those listed in theissue of the DoDISS cited in the solicitation. Unless otherwise specified theissues of documents not listed in the DoDISS are the issues of the documentscited in the solicitation (see 6.2).AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI B46.l - Surface Texture (

14、Surface Roughness,Waviness, and Lay).(Application for copies should be addressed to the American NationalStandards Institute, Inc., Attn: Customer Service, 11 West 42nd Street, NewYork, NY 10036.)AMERICAN SOCIETY FOR QUALITY (ASQ)ASQC Z1.4 - Sampling Procedures and Tables for Inspection byAttributes

15、.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24560A(SH)3(Application for copies should be addressed to the American Society forQuality, 611 East Wisconsin Avenue, Milwaukee, WI 53202-4606.)ILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA

16、 (IESNA)IESNA Lighting Handbook.(Application for copies should be addressed to the IlluminatingEngineering Society of North America, 120 Wall Street, Floor 17, New York, NY10005-4001.)INTERNATIONAL ORGANIZATION FOR STANDARDS (ISO)ISO/CIE 10527 - CIE Standard Colorimetric Observers.(Application for c

17、opies should be addressed to the American NationalStandards Institute, Inc., Attn: Customer Service, 11 West 42nd Street,New York, NY 10036.)UNDERWRITERS LABORATORIES (UL)UL 486A - Wire Connectors and Soldering Lugs for Use withCopper Conductors.(Application for copies should be addressed to the Und

18、erwritersLaboratories, Inc., Publications Stock, 333 Pfingsten Road, Northbrook, IL60062.)2.4 Order of precedence . In the event of a conflict between the textof this document and the references cited herein (except for relatedspecification sheets), the text of this document takes precedence. Nothin

19、g inthis document, however, supersedes applicable laws and regulations unless aspecific exemption has been obtained.3. REQUIREMENTS3.1 Specification sheets . The individual item requirements shall be asspecified herein and in accordance with the applicable specification sheet.In the event of any con

20、flict between requirements of this specification andthe applicable specification sheet, the latter shall govern.3.2 First article . When specified (see 6.2), a sample shall besubjected to first article inspection in accordance with 4.2.3.3 Parts and materials . Parts and materials shall be as specif

21、iedherein and in the applicable specification sheets. Where a definite materialis not specified, a material shall be used which will enable the lightassembly or glassware to meet the requirements of this specification.3.3.1 Recycled, recovered, or environmentally preferable materials .Recycled, reco

22、vered, or environmentally preferable materials should be used tothe maximum extent possible provided that the material meets or exceeds theoperational and maintenance requirements, and promotes economicallyadvantageous life cycle costs.3.3.2 Metals . Metals shall be of the corrosion-resistant type a

23、sspecified in the applicable specification sheet, or they shall be treated toresist corrosion as specified in MIL-E-917. Dissimilar metals in contact witheach other shall be in accordance with MIL-E-917.3.3.2.1 Aluminum . Unless otherwise specified (see 3.1), aluminumalloys, except castings, shall c

24、onform to American Society for Testing andMaterials (ASTM) standards. Aluminum alloy castings shall be manufacturerschoice except sand castings and permanent mold castings shall conform to class4 of MIL-STD-2175; grade shall be manufacturers choice.Provided by IHSNot for ResaleNo reproduction or net

25、working permitted without license from IHS-,-,-MIL-DTL-24560A(SH)43.3.3 Nonmagnetic materials . Unless otherwise specified (see 3.1), allparts shall be of a nonferrous material or a material generally considerednonmagnetic. The magnetic permeability shall be 2.0 or less after fabrication(see 4.4.1.9

26、).3.3.4 Nonmetallic materials . Nonmetallic materials shall benonflammable, nontoxic and fungus-inert as specified in MIL-E-917.3.3.5 Plastics . Plastic materials shall conform to the requirements ofMIL-E-917 and as specified hereinafter.3.3. 6 Glassware . Glassware shall be high-impact, heat resist

27、ant withan extremely low-temperature coefficient of expansion. The glass shallwithstand exposure to atmospheric sea conditions, particularly that of saltwater, high humidity, and bright sunlight without etching, discoloration, orany change in the light transmittance.3.3.7 Commercial (hardware) parts

28、 . Where a definite material is notspecified for utility hardware (items such as screws, bolts , and nuts),commercial items may be used provided they meet the requirements specifiedherein (see 3.3.2, 3.3.3 , and 3.3.4).3.3.8 Caulking compound . Caulking compound shall be of a goodcommercial grade ma

29、terial compatible with the material of the basic lightassembly. Compound consistency shall be such that the light assembly can bedisassembled without requiring the use of special agents or tools.3.3.9 Antiseize coating . Aluminum and CRES fastening parts such asscrews and bolts in contact with threa

30、ded aluminum shall be coated with anantiseize compound in accordance with MIL-T-22361.3.3.10 Gaskets . Unless otherwise specified (see 3.1), gaskets shall becommercial type neoprene 6-75 Durometer hardness.3.3.11 Prohibited materials . The prohibited materials shall be thosespecified in MIL-E-917. U

31、nless otherwise specified (see 3.1), asbestos shallnot be used.3.4 Design and construction .3.4.1 Light assemblies . Light assemblies shall be of the design,construction , and physical dimensions specified (see 3.1). Unless otherwisespecified (see 6.2), lamps shall not be furnished.3.4.1.1 Dimension

32、al tolerances . Unless otherwise specified (see 3.1),the following tolerances shall apply to dimensions specified in the individualspecification sheets:(a) Fractional dimensions - plus or minus 1/64 inch.(b) Decimal dimensions - plus or minus 0.005 inch.(c) Angular dimensions - plus or minus 1/2 deg

33、ree.Unless otherwise specified (see 3.1), a tolerance of plus or minus 1/32 inchis acceptable on fractional dimensions that are controlled by welding orbrazing. The width tolerance shall not interfere with the interchangeabilityof assemblies or parts. A tolerance of plus or minus 1/32 inch with a dr

34、aftangle is acceptable for cast parts.3.4.1.2 Enclosures . Light assemblies shall be type I, splashproof ortype II, submersible as specified (see 1.2 and 3.1).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24560A(SH)53.4.1.3 Drilling, counte

35、rsinking, and tapping . Drilling,countersinking, and tapping shall be done before placing or finish is applied.All holes shall have burrs removed.3.4.1.4 Sharp edges . Sharp edges and corners shall be given a slightradius.3.4.1.5 Finishes . Surface finishes shall be in accordance with ANSIB46.l. Sco

36、re marks on side walls of all light assemblies in the way of nylonstuffing tubes shall be not greater than 123 microinches.3.4.1.6 Threaded parts and fastening devices . Screw threads in copper,aluminum and plastic and fastening of parts shall be in accordance with MIL-E-917 and as specified (see 3.

37、1).3.4.1.7 Wiring . Where required (see 3.1), internal wiring shall befurnished and installed. Connections at screw terminals shall be made withpressure grip ( solderless) connectors in accordance with UL 486A. Spliceconnections shall be kept to a minimum and shall be made with UL approvedinsulated

38、connectors, either crimp or screw type. There shall be no exposeduninsulated electrical terminal joints, junctions, wiring, or wiringaccessories.3.4.1.8 Castings and molded parts . Castings shall be free of coldshuts, blow holes, or any imperfections that may affect the strength orperformance. Flash

39、 shall be removed from molded parts.3.4.1.9 Stress relief .3.4.1.9.1 Metals . Metals used in fabrication and assemblies which aresusceptible to stress shall be stress relieved to prevent deterioration orfailure.3.4.1.9.2 Plastics . Measures shall be taken in molding or processingplastics to insure t

40、hat stress buildup does not occur or is treated to relievethese stresses when required to prevent deterioration of the part or assembly.3.4.1.10 Welding . Welding and allied processes used in fabricationshal1 be in accordance with MIL-STD-278 except welder qualification is notrequired.3.4.1.11 Paint

41、ing . Unless otherwise specified (see 3.1) painting,where required, shall be in accordance with MIL-E-9l7.3.4.1.12 Gaskets . Rubber gaskets shall be securely cemented at thescarf joint and shall completely fill the groove without stretching orbunching. The gasket shall be retained in its groove with

42、out the use ofcement.3.4.1.13 Lubrication . O - ring and tubular gaskets shall be coated witha compound in accordance with MIL-S-8660 before final assembly in the lightassembly.3.4.2 Glassware . Glassware shall consist of lenses, globes , androundels of the classes specified (see 1.2). The design, c

43、onstruction , andphysical dimensions shall be as specified (see 3.1) and hereinafter.3.4.2.1 Coloring . Colored glassware shall be of uniform coloringthroughout the entire thickness of the portions designed for lighttransmittance.Provided by IHSNot for ResaleNo reproduction or networking permitted w

44、ithout license from IHS-,-,-MIL-DTL-24560A(SH)63.4.2.2 Thickness tolerances . Glassware shall be of uniform thicknessthroughout. Where thickness tolerances are not specified (see 3.1), avariation of l2 percent above or below the nominal dimensions will bepermitted, except that these tolerances shall

45、 in no case exceed l/16 inch.3.4.2.3 Edges . Edges of all glassware shall be ground or molded to atrue surface.3.4.2.4 Fresnel type lens . The fresnel type lens of class l and 3glassware shall have a central bulls eye with the required number of zonesabove and below the central zone to meet the perf

46、ormance requirementsspecified herein. Actual design as to the surface curvature, spacing of thezones, width of the zones and so forth shall be at the option of themanufacturer.3.5 Performance characteristics .3.5.1 Light assemblies .3.5.1.1 Operation . Light assemblies, when operated as specified in

47、4.4.1.1, shall perform their specified function.3.5.1.2 Degree of enclosure . Type I and type II light assemblies shallconform to the splashproof and submersible (1600 foot) requirements,respectively, of MIL-STD-108 (see 4.4.1.2). Following the enclosure test, theassemblies shall satisfactorily pass

48、 the dielectric withstanding voltage andinsulation resistance tests (see 4.4.1.6 and 4.4.1.7).3.5.1.3 Shock . Light assemblies shall conform to the class I or classII (see 3.1), grade A shock requirements of MIL-S-901 (see 4.4.1.3).Following the shock test, the light assemblies shall satisfactorily

49、pass thedielectric withstanding voltage test (see 4.4.1.6). Lamp failure shall not beconsidered as an assembly failure.3.5.1.4 Vibration . Light assemblies shall conform to the type Ivibration requirement of MIL-STD-167-l and shall exhibit no signs of damage orloosening of parts during and after the vibration test (see 4.4.1.4).Following the vibration test, the light assemblies shall satisfactorily passthe dielectric withstanding voltage test (if applicable) (see 4.4.1.6).3.5.1.