NAVY MIL-DTL-24552 B-2001 TERMINALS AND SEALS PLUGS AND SWITCH CASUALTY POWER SYSTEMS RECEPTACLE TYPE GENERAL SPECIFICATION FOR《插座类意外电能系统终端和密封插塞开关总说明书》.pdf

《NAVY MIL-DTL-24552 B-2001 TERMINALS AND SEALS PLUGS AND SWITCH CASUALTY POWER SYSTEMS RECEPTACLE TYPE GENERAL SPECIFICATION FOR《插座类意外电能系统终端和密封插塞开关总说明书》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24552 B-2001 TERMINALS AND SEALS PLUGS AND SWITCH CASUALTY POWER SYSTEMS RECEPTACLE TYPE GENERAL SPECIFICATION FOR《插座类意外电能系统终端和密封插塞开关总说明书》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments (recommendations, additions, deletions) and any pertinentdata which may be of use in improving this document should be addressed to: Commander, SEA 05Q, Naval Sea Systems Command, 1333 Isaac Hull Ave SE,Washington Navy Yard, Washington D.C. 20376, by using the StandardizationDocu

2、ment Improvement Proposal (DD form 1426) appearing at the end of thisdocument or by letter.AMSC N/A FSC 5940DISTRIBUTION STATEMENT A. Approved for public release; distribution isunlimited.INCH-POUNDMIL-DTL-24552B(SH)8 June 2001 SUPERSEDINGMIL-T-24552A(SH)3 November 1986DETAIL SPECIFICATIONTERMINALS

3、AND SEALS, PLUGS AND SWITCH,CASUALTY POWER SYSTEMS, RECEPTACLE TYPE,GENERAL SPECIFICATION FORThis specification is approved for use by the Naval Sea SystemsCommand, Department of the Navy, and is available for use by allDepartments and Agencies of the Department of Defense.1. SCOPE1.1 Scope. This sp

4、ecification covers terminals and seals, seals,plugs, and switches that provide emergency electric power connections forcasualty power systems. The capacity of these devices is 450-volt alternatingcurrent (Vac), 3-phase, 100- and 200-ampere for use on Naval ships, and othercharacteristics as specifie

5、d (see 6.2).2. APPLICABLE DOCUMENTS2.1 General. The documents listed in this section are specified insections 3 and 4 of this specification. This section does not includeddocuments cited in other sections of this specification or recommended foradditional information or as examples. While every effo

6、rt has been made toensure the completeness of this list, document users are cautioned that theymust meet all specified requirements documents cited in sections 3 and 4 ofthis specification, whether or not they are listed.2.2 Government documents.2.2.1 Specifications, standards, and handbooks. The fo

7、llowingspecifications, standards, and handbooks form a part of this document to theextent specified herein. Unless otherwise specified, the issues of thesedocuments are those listed in the issue of the Department of Defense Index ofSpecifications and Standards (DoDISS) and supplement thereto, cited

8、in thesolicitation (see 6.2).SPECIFICATIONSFEDERALQQ-B-654 - Brazing Alloys, Silver.QQ-S-365 - Silver Plating, Electrodeposited, GeneralRequirements for.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24552B(SH)2DEPARTMENT OF DEFENSEMIL-PRF-9

9、00 - Rubber Gasket Material, 45 DurometerHardness.MIL-S-901 - Shock Tests, H.I. (High-Impact) ShipboardMachinery, Equipment, and Systems,Requirements for.MIL-E-917 - Electric Power Equipment, BasicRequirements.MIL-PRF-5624 - Turbine Fuel, Aviation, Grades JP-4,JP-5, and JP-5/JP-85T.MIL-F-16884 - Fue

10、l, Naval Distillate.MIL-DTL-24552/1 - Terminals and Seals, Plugs and Switch,Casualty Power, Receptacle Type, BackConnected, 200-Ampere, 450-VoltAlternating Current, Three-Phase, SymbolNo. 1046.MIL-DTL-24552/2 - Terminals and Seals, Plugs and Switch,Casualty Power, Receptacle Type, Upperand Lower Ris

11、er, 200-Ampere, 450-Volt,Alternating Current, Three-Phase, SymbolNo. 1047.MIL-DTL-24552/3 - Terminals and Seals, Plugs and Switch,Casualty Power, Seal, Symbol No. 1048.MIL-DTL-24552/4 - Terminals and Seals, Plugs and Switch,Casualty Power, Plug, 100-Ampere, 450-Volt, Alternating Current, Three-Phase

12、,Symbol No. 1049.MIL-DTL-24552/5 - Terminals and Seals, Plugs and Switch,Casualty Power, Switch, Portable 100-Ampere, 450-Volt, Alternating Current,Three-Phase, Symbol No. 1041.1.MIL-C-39029 - Contacts, Electrical Connector, GeneralSpecification for.STANDARDSFEDERALFED-STD-H28 - Screw-Thread Standar

13、ds for Federal Services.FED-STD-H28/2 - Screw-Thread Standards for Federal Services,Section 2, Unified Inch Screw Threads - UNand UNR Thread Forms.FED-STD-595 - Colors Used in Government Procurement.DEPARTMENT OF DEFENSEMIL-STD-108 - Definitions of and Basic Requirements forEnclosures for Electric a

14、nd ElectronicEquipment.MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment(Type I - Environmental and Type II -Internally Excited).MIL-STD-202 - Test Methods for Electronic and ElectricalComponent Parts.MIL-STD-810 - Environmental Test Methods and EngineeringGuidelines.MIL-STD-889 - Dissimi

15、lar Metals.MIL-STD-1344 - Test Methods for Electrical Connectors.(Unless otherwise indicated, copies of the above specifications,standards, and handbooks are available from the Defense Automated PrintingService, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)2.3 Non-Government publica

16、tions. The following document(s) form a partof this document to the extent specified herein. Unless otherwise specified,the issues of the documents which are DoD adopted are those listed in theissue of the DoDISS cited in the solicitation. Unless otherwise specified, theProvided by IHSNot for Resale

17、No reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24552B(SH)3issues of documents not listed in the DoDISS are the issues of the documentscited in the solicitation (see 6.2).AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)ASTM A 313 - Standard Specification for Stainless S

18、teelSpring Wire. (DoD adopted)ASTM B 187 - Standard Specification for Copper Bar, BusBar, Rod and Shapes.ASTM B 633 - Standard Specification for ElectrodepositedCoatings of Zinc on Iron and Steel.(DoD adopted)ASTM B 695 - Standard Specification for Coatings of ZincMechanically Deposited on Iron and

19、Steel.ASTM D 2240 - Standard Test Method for Rubber Property -Durometer Hardness. (DoD adopted)ASTM D 5948 - Standard Specification for Molding Compounds,Thermosetting.ASTM F 1836M - Standard Specification for Stuffing Tubes,Nylon, and Packing Assemblies.(Application for copies should be addressed t

20、o the American Society forTesting and Materials, 100 Barr Drive, West Conshohocken, PA 19428-2959.)SOCIETY OF AUTOMOTIVE ENGINEERS (SAE)AMS R 6855 Elastomer, Synthetic, Sheets, Strips, Moldedor Extruded Shapes, General Specification.(Application for copies should be directed to the Society of Automo

21、tiveEngineers, 400 Commonwealth Drive, Warrendale, PA 15096-0001.)AMERICAN WELDING SOCIETY (AWS)AWS A5.8 - Specification for Filler Metals for Brazing.DoD adopted)(Application for copies should be addressed to the American WeldingSociety, 550 NW LeJeune Road, Miami, FL 33126.)2.4 Order of precedence

22、. In the event of a conflict between the textof this document and the references cited herein (except for relatedassociated specifications or specification sheets), the text of this documenttakes precedence. Nothing in this document, however, supersedes applicablelaws and regulations unless a specif

23、ic exemption has been obtained.3. REQUIREMENTS3.1 Specification sheets. The individual item requirements shall be asspecified herein and in accordance with the applicable specification sheet. Inthe event of any conflict between the requirements of this specification andthe specification sheet, the l

24、atter shall govern.3.2 Qualification. Unless otherwise specified (see 3.1), the casualtypower terminals, plugs, and seals furnished under this specification shall beproducts that are authorized by the qualifying activity for listing on theapplicable qualified products list before contract award (see

25、 4.2 and 6.3).3.3 Materials and processes. Materials and processes shall be asspecified herein and in 3.1.3.3.1 Metals. Metals shall be in accordance with MIL-E-917 to providecorrosion resistance. Metals that are not inherently corrosion-resistant shallbe processed (treated, plated, or painted) to p

26、rovide corrosion resistance.Cadmium treatments shall not be used.3.3.1.1 Selection of metals in direct contact. In order to minimizecorrosion attack due to electrolytic action between dissimilar metals inProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

27、,-MIL-DTL-24552B(SH)4contact with each other, metal-to-metal contact shall be limited to thosemetals which, when coupled, are in accordance with MIL-STD-889.3.3.2 Nonmetallic materials. Nonmetallic materials shall benonflammable and nontoxic in accordance with MIL-E-917. Materials containingasbestos

28、 shall not be used. PVC materials shall not be used.3.3.2.1 Thermosetting insulating material. Thermosetting moldedinsulating parts shall be type MAI-60 in accordance with ASTM D 5948, or oneof the following: Fiberite No. 5064, ARMC No. 446 or equal.3.3.2.2 Gaskets and seals. Material for gaskets an

29、d seals shall bein accordance with SAE-AMS-R-6855, class 2, type B or in accordance withMIL-PRF-900.3.3.3 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used tothe maximum extent possible provided that the material

30、 meets or exceeds theoperational and maintenance requirements, and promotes economicallyadvantageous life cycle costs.3.4 Parts. 3.4.1 Contacts. The contact pins and contact sockets shall be of acopper or copper-alloy material that will provide the required electricalcharacteristics. The contacts sh

31、all be silver-plated with not less than 0.0002inch of silver in accordance with QQ-S-365.3.4.1.1 Contact pins. Plug-mounted pins shall meet the physical,electrical, and performance requirements as specified in 3.1 and 3.6. Thecontact-pin and end lugs shall be crimp style and insulated. Lugs shall be

32、appropriately sized to accept American Wire Gauge (AWG) size no. 4 copperconductors applied with standard crimping tools.3.4.1.2 Contact sockets. The terminal contact sockets shall be sizedto accept the contact pins and meet the physical, electrical, and performancerequirements as specified in 3.1 a

33、nd 3.6. Socket contact springs, if requiredfor mechanical strength, shall be corrosion-resistant steel wire in accordancewith ASTM A 313. The spring shall not form a part of the electrical circuit.3.4.2 Terminal lugs. Terminal assembly lugs shall be of a copper orcopper-alloy material, crimp style,

34、and insulated. Lugs shall be sized forattachment to 0.250-inch diameter studs and to accept conductors size no. 2wire. Lugs shall be formed to a 45-degree angle to aid in installation ofconductors.3.4.3 Hardware. Hardware (bolts, nuts, screws, washers, andmiscellaneous hardware) shall be of a good c

35、ommercial grade materialcompatible with that of the basic unit. Steel (corrosion-resisting steelexcepted) hardware shall be zinc-plated in accordance with ASTM B 633 orASTM B 695.3.5 Design and construction. Terminal, plugs, seals, and switchesshall be of the design, construction, and physical dimen

36、sions specified(see 3.1).3.5.1 Mounting. The size and location of mounting holes shall be asspecified (see 3.1).3.5.2 Housings. Housings for terminals, plugs, covers, and switchenclosure shall be of a glass-fiber, reinforced molded thermosettinginsulating material. The color shall be red (color no.

37、11105 or 11136 inaccordance with FED-STD-595).3.5.2.1 Housing - Terminal. The terminal housing shall have aProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24552B(SH)5removable access cover and a cavity of sufficient size to enable ease ofmaki

38、ng internal electrical connections and shall have 3-phase outletscontaining bus, assembled socket contacts, and protective covers. The socketcontacts shall be removable, rigidly mounted, and shall allow for a radialmisalignment of plus or minus 0.020 inch. The outlets shall be polarized toprevent cr

39、oss-phasing and shall contain threaded inserts for retaining plugsand covers. Removal of plugs and protective covers shall not cause the socketcontacts, connecting bus, or wire to become loose.3.5.2.2 Housing - Plug. The plug housing shall protrude beyond andafford protection for the contacts. The p

40、lugs shall have male contact pins,retaining devices that mate with the terminal housing threaded inserts, andshall be polarized to prevent cross-phase engagement. To facilitate self-alignment of mating contacts, the contact pins shall be retained so that theindividual contact shall have an overall s

41、ideplay of 0.002 to 0.006 inch. Toprevent accumulation of condensation or moisture while connected to theterminals, vent holes shall be utilized.3.5.2.3 Protective covers. A protective cover shall provide a spray-tight seal at the terminal or switch interface when fully engaged and retainedwith devi

42、ces specified in 3.5.3. Vent holes shall be incorporated into thecover to allow condensation and moisture to drain. The protective cover shallbe held captive to the terminal housing or switch enclosure by means of aflexible, plastic-coated, stainless steel cable. Phase identification (A, B,and C) sh

43、all not be marked on the protective covers.3.5.3 Retaining devices. The protective cover shall contain captiveretaining devices. The retaining devices shall provide positive closure andrelease without the use of tools. The retaining devices shall not be used asan aid for mating or separating plugs o

44、r covers to and from terminals.3.5.4 Plug engaging and separating. Lubricants, tools, retaining, orcoupling devices shall not be required for engaging or separating a plug fromthe receptacle.3.5.5 Cable entry boot - Plug. A removable flame-retardant,polyetherurethane cable entry boot shall be provid

45、ed with each plug. The shoreA hardness change of the boot shall be not greater than 10 after beingsubjected to the humidity test of 4.7.8. The boot shall be held in place witha stiffener plate to prevent water leakage into the cable end of the plughousing.3.5.6 Cable entry seal - Upper and lower ter

46、minal riser. Whenspecified (see 3.1), a nylon stuffing tube shall be furnished with each upperand lower terminal riser.3.5.7 Screw threads for fastening devices. Screw threads for allthreaded fastening devices shall be in accordance with FED-STD-H28. Unlessotherwise specified (see 3.1), the threads

47、shall be right-hand, coarse-threadseries, unified form, class 2A or 2B in accordance with FED-STD-H28/2. Unlessotherwise specified (see 3.1), when a screw mates with a plastic part, athreaded metal insert, bushing type or helical type, shall be molded therein.The bushing type is the preferred type.3

48、.5.7.1 Thread locking. Nuts, bolts, studs, and screws used forelectrical connections shall be secured by lockwashers. Bolts, nuts, andscrews used for mechanical connections shall be secured by locking devices, asrequired, to ensure compliance with the requirements specified (see 3.1).3.5.8 Brazing.

49、Brazing alloys for electrical connections shall be inaccordance with AWS A5.8 or QQ-B-654.3.5.9 Electrical rating. The electrical rating of the terminals shallbe 200-ampere per phase, 450-Vac, 3-phase. Rating of plugs and switches shallbe 100-ampere per phase, 450-Vac, 3-phase.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24552B(SH)63.5.10 Phase identification. Phase identification (A, B, and C) shallbe p