NAVY MIL-C-17415 F-1989 CLOTH COATED AND WEBBING INFLATABLE BOAT AND MISCELLANEOUS USE《带子膨胀船混合使用涂层布料》.pdf

《NAVY MIL-C-17415 F-1989 CLOTH COATED AND WEBBING INFLATABLE BOAT AND MISCELLANEOUS USE《带子膨胀船混合使用涂层布料》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-17415 F-1989 CLOTH COATED AND WEBBING INFLATABLE BOAT AND MISCELLANEOUS USE《带子膨胀船混合使用涂层布料》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、r MIL-C-17415F 3 7777906 03OLt57 7 MIM-17415F 31 May 1989 SUPERSEDING MIM-17 4 15E 16 April 1964 (See 6.5) MILIITARY smc1FICATIoN CLM“, CDATED, AND WEBBING, I“ABE BOAT AND MIScEL;LANMxJS USE This specification is approved for use by all Deprbnents and Agencies of the Department of Defense. 1. SOPE 1

2、.1 Scope. This specification establishes the requirmts for cured coat distribution is unlimited. -. I THIS DOCUMENT CONTAINS i8 PAGES; Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-IJ74LSF 83 m 7779706 O380458 O m MIM-17415F Type8 Class A Cla

3、ss B Type9 Class A Class B Type 10 Type 11 Type 12 Type 13 Type 14 Type 15 Type 16 Class A Class AA Class B Type 17 - - 6.5 ounces per square yard (natural rubber). - 6.5 ounces per square yard (synthetic rubber). - - 30.4 ounces per square yard (synthetic rubhr) . - 33.4 ou11ces per square yard (na

4、tural rubber). - 30.5 ounces per square yard. - 34.5 ounces per square yard. - 45.1 ounces per square yard. - 12.1 ounces per square yard. - 45.3 ounces per square yard. - Webbing, 3-inch width, dyed. - 22.8 ounces per square yard (synthetic rubber). - 16.8 ounces per square yard (synthetic rubber).

5、 - 22.8 ounces per square yard (natural rubber). - - 40.5 ounces per square yard. 2. APPUCmrn DOCUMENTS 2.1 GavernmentdocumentC. 2.1.1 spec ifications and staxlards. The follow-q specifications and standards form a part of this document to the extent specified herein. otherwise specified, -the issue

6、s of these documents are those listed in the issue of the Department of Defense 1nde.x of Specifications and %andards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Unless SPECIF“I0N MILJTARY MIGW-17337 - Webbing, Textile, Woven Nylon. MILIITARY MIGSIW105 - Sampling procedures

7、 ancl Tables for Inspection by Attributes. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Naval publications and Forms Center, (AT“: NPOIX;), 5801 Tabor Avenue, Philadelphia, PA 19120-5099. ) 2 ,_ - . -I Provided by IHSNot

8、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-LLIIJF 3 = 7779906 0380457 2 MIM-17415F 2.2 Non-Gavenmient Mzblications. The follahg documents fonn a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documente whi

9、ch are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, the issues D 297 - Standard Methds for FUbber products - Chemical Analysis.

10、 (DOD adoptai) D 412 - Standard Test Methods for -ber Properties in Tension. (DOD adopted) D 572 - Standard Test Method for Fubber - Deterioration by Heat and Oxygen. (DOD adopted) D 750 - Standard Test Method for Rubber Deterioration mn-Arc Weathering Apparatus. (DoD adopted) D 751 - Standard Metho

11、ds of Testing Coated Fabrics. (DOD adopted) D 815 - Standard Method for Testing Coated Fabricc - Hydrogen Penneable. D 1682 - Standard Test Methods for Breaking md and Elongtion of Textile Fabrics. D 2261 - Standard Tect Methcd for Tearing Strength of Woven Fabrics by the Tongue (Single Rip) Method

12、(Constant- Rate-of-Extension Tensile Testhg Machine). (DOD adopted) D 3776 - Standard Test Methods for Mass Per Unit Area (Weight) of Woven Fabric. (Application for copies should be addressed to the American Society for Test- and Materials, 1916 Race Street , Mladelphia, PA 19103. ) (Non-Goveniment

13、standm and other publications are normally available from the organizations that prepare or distribute the documents. documents also may be available in or through libraries or other informational services.) These 2.3 Order of precedence. in the event of a conflict between the text of this document

14、and the references cited herein, the text of this document takes precedence. Nothing in this docmnent, however, supersedec applicable laws and regulations unless a cpecific exemption has been obtained. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

15、,-flIL-C-LiLILSF 83 W 7777906 0380qb0 9 MIGC-17415F 3.1 Materials. 3.1.1 Cloth. The base material used in the construction (see table I) of coated cloth shall be cotton or nylon which shall meet the requirements established by this specification. Cotton cloth shall be unbleached, contain no more tha

16、n 3 percent maximum nonfibrous materials and be chemically neutral, having a pH between 6.5 and 7.6. Cotton cloth weighing up to and including 5 ounces per square yard shall be singed. unbleached, of high tenacity, kmproved heat and light resistant (nylon 6 or 6/6), heat set and scoured, contain no

17、more than 3 percent maximum nonfibrous materials and have a pH between 5.0 and 8.0. specified (see 4.3 and 6.2). Nylon cloth shall be bright, ength and width shall be as Asbestos is prohibited. TAl3LE I. Cloth and webbincl construction. used in type land8 2 3 4 5and9 6, 10, and 11 7 12 13 14 15 16 1

18、7 Fiber Nylon Nylon Cotton Cotton Nylon Nylon (pile c10th)I Cotton Nylon (pile 10th) Nylon Nylon Nylon webbirg Nylon Nylon Breaking strength, minimum pounds per inch of width warp 40 150 40 80 300 150 NREQT 19 5 600 ! 3000 N mQT 4 NREQT 400 Filling 40 14 O 40 80 3 O0 NlWX 145 N REQT 195 600 NREQT NR

19、EQT 400 fleight, maximum ounces per square Yard 1. o 2.5 2.1 4.5 5.4 8.5 7.5 8.2 3.1 13.3 2.2 linear yard 4.8 8.5 I Types 6, 10, and 11 cloth shall be compsed of two nylon fabrics joined by a minimum of 30 pile yarns per square inch so that the fabrics are spaced a rninh of 2-1/4 inches apart or a m

20、aximum of 3 inches apart after heat setting. The warp yarn shall be 2 ply, 70 denier yarn, and the filling shall be a single, 210 denier yarn before heat setting. The pile warp yarn shall be either 2 ply, 70 denier yarn or a single, 210 denier yarn before heat setting. 4 Provided by IHSNot for Resal

21、eNo reproduction or networking permitted without license from IHS-,-,-P Footnotes - Continued g/ The pile cloth of type 12 shall be composed of two nylon fabrics joined by a minhum of 30 pile yarns per square inch so that the fabrics are spa4 Iivdrostatic resistance. The hydpstatic resistance of typ

22、es 2, 3, and 5 cloth shall be not less than 100 lb/h (see table V) . 3.5 Roll lensthc . There shall be not mre than two pieces in any roll of coated fabric, and neither piece shall be less than 10 yards long. 3.6 Worlaanchip. The finished cloth and webbing shall conform to the quality and grade of p

23、roduct-established by this specification. not excee the level specified. Defects shall 10 ,- a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I Characteristic Total weight oz also lot avg for caprison with avg after aging axi after weathering Pass o

24、r fail (evidence of cracking) Avg of all determinatiors in each direction carpared with avg of all determiraticm before expsure, reported in percent loss for warp ad fittiw Pass or fail AWJ of all determinatims in each direction separately, capred to nearest 1.0 lb with avg of all determinatiors bef

25、ore -re, reported in percent lbss Pass or fail (evidence of cracking) Avg of the five determimtias to the minimm (typxi 2, 3, nearest 1.0 ib/in2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIM-17415F 1 To be reported separately for each determina

26、tion in the unit of product. ? Except that hydrostatic determination is not required and that speck shall be subjecta3 to minus 20 _+ 2 degrees Fahrenheit (OF) for 94 _+ 1/2 hours before testing. 4. QUUTY ASSURANCE PROVISIONS 4.1 Responsibility for inspsction. Unless otherwise specified in the contr

27、act or purchase order, of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contrac- tor my use his own or any other facilities suitable for the performance of the inspection requirements specified herein, u

28、nless disapproved by the Government. tions set forth in the specification where such inspctions are deemed necessary to encure supplies and services conform to prescribed requirements. the contractor is responsible for the performance The Government reserves the right to perform any of the inspec- 4

29、.1.1 Responsibility for compliance. All items shall meet all require- The absence of any inspection requirements in the specification ments of sections 3 and 5. shall become a part of the contractors overall inspection system or quality shall not relieve the contractor of the responsibility of ensur

30、ing that all: products or supplies submitted to the Government for acceptance comply with all requirements of the contract (see 6.3). the manufacturm operations, is an acceptable practice to ascertain confom- ance to requirements, however, this does not authorize submission of known defective materi

31、al, either indicated or actual, nor does it conmit the The inspection set forth in this specification _I program, Sampling inspection, as part of .Government to accept defective material. 4.2 Oualitv conformance inspection. Quality conformance inspection shall be in accordance with 4.2.1 through 4.3

32、. 4.2.1 Base cloth. The base fabric shall be tested as specified in table VI. apply to the average of the determinations made on a unit of product for the test purposes specified in the applicable test method. shall be 1 yard, full width, of the uncoated base fabric. shall be in accordance with tabl

33、e VII. The lot shall be unacceptable if any unit fails to meet any of the requirements specified. The physical and chemical values specified in 3.1.1 and table I The unit of product The sample size 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c

34、 MIL-C-17415F 83 m 9999906 0380469 5 W MIX-17415F TABLF: Vi. Test methodc. Characteristic Cottm cloth: color Ncnf ibas mterials, percent muOD FAR Supplement 27.475-1 exempts the requirement for a DD Form 1423. Reference suggested Paraqraph DID Nunhr DID Title Tailorbq 4.1.1 DI-E-2121 Certificate of

35、Compliance The above DIDS were those cleared as of the date of this specification. The current issue of DoD 5010.12-L, Acquisition Management Systems and Data Requirements Control List (AMSDL), must be researched to ensure that only current, cleared DIDS are cited on the DD Form 1423. 6.4 Subi& term

36、 (key word) list-. Cotton Nylon Rubber synthetic 6.5 Chmes from previous issue. Marginal notations are not.& in this revision to identify charges with respect to the previous issue due to the extensiveness of the changes. Custodians: . Amsi-m Navy - SH Review activities: my-ME DIA - CI Preparing activity: Navy - SH (Project 8305-0198) User activities: Amsi-ME,cE Navy - MC, OG +?US. GOVERNMENT PRINI1NC OFFICE: 1989 - 6W-33/t3386 18 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-