NAVY MIL-B-19107 A-1957 BOX METAL TOTE NESTING TYPE《嵌套型手提金属箱》.pdf

《NAVY MIL-B-19107 A-1957 BOX METAL TOTE NESTING TYPE《嵌套型手提金属箱》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-B-19107 A-1957 BOX METAL TOTE NESTING TYPE《嵌套型手提金属箱》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、1 Aumst 1957 SUPERSEDING MIL-B-19107 (SU) 22 July 1955 MILITARY SPECIFICATION BOX, METAL, TO-, NESTING TYPE; 1. SCOPE 1.1 Scope.- This specification covers nesting type, metal, tote, boxes for use in the storage of small items in stable stacked tiers. 1.2 Classification.- Nesting type, metal,tate bo

2、xes shall be of the following specified types and sizes: Type I - Heavy duty, nesting, metal, tote box with bottom runners and spun handles, having 9c20 pounds load bearing capacity across the handles (Figs. 1 and 3) Type II- General purpose, nesting, metal, tote box without bottom runners and spun

3、handles, having 600 pounds load bearing capacity across the handles (Figs. 2 and 4) long by 12 3/16 inches wide by 7 3/8 inches high (Figs. 1 and 2) long by 9 5/16 inches wide by 6 i/ wood, wirebound. PPP-8-591 - Boxes; fiberboard, wood-cleated. PPP-Bo601 7 Boxes; wood, cleated-plywood. PPP-3-621 -

4、Boxes; -061, nailed and lock-corner, PPP-B-636 -. Boxes, fiber . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-19107A (S wood-cleated, veneer, paper overlaid. MIL-L-10547 - Liners, case, waterproof. STANDARDS Federal Federal Standard No. 595

5、- Colors. Military MIL-STD-105 - Sampling Procedures and Tables for Inspection MILSID-129 - Marking for Shipment and Storage. (Copies of, specifications and standards required by contractors should be obtained from the procuring activity or as directed by the Contracting Officer. ) by Attributes. 2.

6、2 shall govern where there is a conflict between any referenced specifi- cation( s) and this specification. Specification precedence.- The requirements of this specification 3.1 General.- Nesting, metal, tote boxes covered by this specification shall be complete and ready for use when delivered. be

7、in accordance with the classification specified in 1.2 and figures Type and size shall 1, 2, 3, and 4. 3.1.1 Preproduction Model.-Unless otherwise specified in the schedule of either the Invitation for Bid or the contract, a preproduction model shall be submitted for examrination, test, and inspecti

8、on in accordance with section 4, and such other tests as are necessary to determine com- pliance with the provisions of this specification and the contract. In all respects not specifically covered by this specification the pre- production model shall be representative of and identical in quality, m

9、aterials, workmanship, and design with the production line unit(s) to be delivered in fulfillment of contract requirements. Delivery of the preproduction model shall be scheduled to allow at least 15 days for evaluation and notification of acceptance, as well as com- pl.etion of the contract by the

10、established date. be automatically extended by the number of days in excess of i5 days that are required for evaluation and notification. based on an evaluation of the design, structural, and operational characteristics relative to safety, operational efficiency, and standard design practice. / -7 2

11、 Completion date will Acceptability shall be Prior to fabrication of the contract requirement, c- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-E19107A( S smooth; free from pits, holes, fissures, and rough projecting edges; and shall be thoroug

12、hly fused. 3.5.1;3 Handles.-Handles shall operate freely without interference from the sides of boxes and shallsnot deform the sides during operation. Welded joints -_ _f 7 I a * * 5 +. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-17107A 51

13、m 7797706 0369117 7 m #IL-B-l%O?A (S however, the Government reserves the Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-19107A (SU) right to obtain any additional information or use any methods deemed necessary to determine compliance with th

14、e requirements of the specification. 4.3.2 Nesting.-With handles h the nesting position, sufficient tote boxes shall be nes.ted to form a stack at least 5 feet high. shall remain upright for a period of.at least 1 hour. then shall be removed separately from the stack. damage to the finish of any tot

15、e box, or difficulty in removing any individual tote box from the stack shall be sufficient evidence of failure to comply with this specification, The stack Each tote box Tipping of the stack, 4.3.3 Maximum load. 4.3.3.1 2iaximum load. tme I (Fim. 1 and 3) box.-Wth handles in the stacking position,

16、each tote box shall support a stack of loaded tote boxes, the gross weight of which is 1,200 pounds, for a period of at least 1 hour. Permanent deformation of the box or handles shall be sufficient evidence of failure to comply with this specification. 4.3.3.2 b?aximum load, tme II (Fips. 2 and 4) b

17、ox.-Wth handles in the stacking position, each tote box shall. support a stack of loaded tote boxes, the gross weight of which is 800 pounds, for a period of at least 1 hour. Permanent deformation of the box or handles shall be sufficient evidence of failure to comply with this specification. 4.4 Mo

18、del approval and unit acceptance.- Approval of models or acceptance of units of equipment for military us,is, in all cases, secondary to satisfactory operation under service conditions. or acceptance of units for a particular contract or order, the duly authorized agent assumes responsibility to the

19、 Government for procurement of items as delivered, but in no war assumes any part of the contractors responsibility for design and satisfactory performance. the equipment fails to meet service requirements of the intended appli- cation, although approved by the duly authorized agent, the contractor

20、is not relieved of responsibility to correct defects and make such changes as may be necessary to meet service requirements, without additional cost to the Government. By approval of models If for any reason 5. PTZEPARATION FOR DELIVERY 5.1 Packing.- Metal tote boxes shall be packed level A, B or C

21、as speci- fied. (See 6,2) 5.1.1 Leval A.-Eetaltote boxes, nested and separated by fiberboard or other suitable material, shall be packed in wirebound wood boxes, wood- cleated fiberboard boxes, d-cleated plywood boxes, nailed wood boxes, fiberboard boxes or paper overlaid veneer boxes conforming to

22、Specifi- cation PPP-B-585 (class 3) , PPP-B-591 (overseas type) , PPP-B-601 (overseas type) , PPP-B-621 (class 2) , JAN-P-108, and NILB-10377 (overseas type) , respectively. liner conforming to Sbecification ML-LlO547 and sealed in accordance with.the appendix thereto. Shipping containers shall be-f

23、itted with a waterproof case Adequate cushioning shall be provided to Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-39307A 51 i 399990b 0369339 O a- MIL-B-lq107A (S of fiberboard boxes, 70 pounds. appendix of the applicable box specification.

24、 5.1.2 Level B,-Metal tote boxes, nested and separated by fiberboard or other suitable material, shall be packed in fiber boxes, wirebound wood boxes, wood-cleated fiberboard boxes, wood-cleated plywood boxes, nailed wood boxes, or paper overlaid veneer boxes conforming to Specification PPP-B-636 (t

25、ype I or II, class i), PPP-B-585 (class 1 or 2), PPP-B-591 (domestic type), PPP-B-601 (domestic type), PPP-B-621 (class i), and MIL-E10377 (domestic type), respec- tively. item within the shipping container. The gross weight of wood and wood-cleated boxes shall not exceed 200 pounds. The gross weigh

26、t of fiberboard boxes shall not exceed the weight limits of the specification. strength of fiberboard boxes shall be 275 pounds, accordance with the applicable specification or appendix thereto. 5.1.3 Level ensure acqtance and safe delivery at destination, shall conform to the carrier rules anil reg

27、ulations applicable to the mode of transportation. 5.2 Marking,- In addition to any special marking required by the contract or order, shipping containers shall be marked in accordance with rfilitary Standard MIL-STD-129. The gross weight Boxes shall be closed and strapped in accordance with the Ade

28、quate cushioning shall be provided to prevent movement of the The minimum bursting Boxes shall be closed in C.-Metal tote boxes shall be packed in a manner which will ShiPPhg containers 6. NOTES 6.1 Intended use.- Tote boxes described herein are intended for storing, picking, and transporting small

29、lots of small parts within activities. When parts are delicate or easily marred, fiberboard liners are provided to protect against damage. are inserted in.tote boxes to allow plac ng more than one item in a tote box. large number in a Limited space. 6.2 Ordering data.- Procurement documents should s

30、pecify the following: When lots are small enough, fiberboard separators Fmpty tote boxes are nestable, to permit palletbed storage of a (a) Title, number,and date of this specification. (b) Tjpe and size of nesting, metal tote box. (1.2) (c) When fiberboard liners are required. (3.3.1) (d When fiber

31、board liners with separators are required* (3.3.2) (e 1 SDecial markings reauired. (3.5.3) (fj Gvel of packing re and the fact that the Government may have formulated, furnished, or in any way supplied the said drawings, specifications, or other data is not to be regarded by: implication or otherwis

32、e a8 in any manner licensing the holder or any other person or corporation, or conveying any rights or permission to manufacture, use, or seil any patented invention that may in any way be related thereto. When Government drawings, specifications, or other data are Preparing activity: Navy - Bureau

33、of Supplies and B;ccounts 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-7 D al - T L 11 rn II I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-E-39307A 53 W 9779706 0367322 O W 1 n 3. 1 I I 1

34、 n I+- - 31 -2 I . .- &-i. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-III 1 I-* I _Cu I I n * I - I ii ? O z J Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-LSL07A 51 = 9999906 0367324 4 ! s : !2 P E * il i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-