NAVY MIL-A-48027 A-1975 ADAPTER-BOOSTER BOMB NOSE THERMALLY PROTECTED M148E1 LOADING ASSEMBLING AND PACKING《M148E1热保护弹头炸弹助推器适配器装载组装和包装》.pdf

《NAVY MIL-A-48027 A-1975 ADAPTER-BOOSTER BOMB NOSE THERMALLY PROTECTED M148E1 LOADING ASSEMBLING AND PACKING《M148E1热保护弹头炸弹助推器适配器装载组装和包装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-A-48027 A-1975 ADAPTER-BOOSTER BOMB NOSE THERMALLY PROTECTED M148E1 LOADING ASSEMBLING AND PACKING《M148E1热保护弹头炸弹助推器适配器装载组装和包装》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、5-37-07 MIL-A-48027A L3 W 777770b 03L550 5 W MIL-A-48027A (PA) 30 June 1975 Sup ers e ding MIL-A- 4 8 O 2 7 14 January i9 72 (MU) MILITARY SPECIFICATION. ADAPTER-BOOSTER, BOMB, NOSE, THERMALLY PROTECTED, M148E1, LOADING, ASSEMBLING AND PACKING This specification is approved for use by all department

2、s and agencies of the Department of Defense. i. SCOPE 1.1 This specification covers the loading, assembling and packing of one type of booster designated as Adapter- Booster, Bomb, Nose, M148E1. 2. APPLICABLE DOCUMENTS 2.1 The following documents OF the issue in effect on date of invitation for bids

3、, or request for proposals form a part of this specification to the extent specified herein. %SPECIFICATIONS MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification for. MIL-P-46464 - Pellets, Tetryl. %STANDARDS MILITARY MIL-STD-105 - Sampling Procedures and T

4、ables for Inspection by Attributes (ABC-STD-105). %P UB LI CATI ONS ASTM-I31692 - Flammability of Plastic Sheeting and Cellular Plastics. 1 FSC: 1325 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-48027A (PA) ASTM-D2044 - Moisture Content in P

5、aper and Paper- ASTM-D792-66-Specific Gravity and Density of Plastics board by Toluene Distillation. by Displacement *DRAWINGS U.S, ARMY PICATINNY ARSENAL 9270711 - Box, Packing, Ammunition for Adapter Boosters Mi47, M148, M148E1, M149 or XM150 9270710 - Support, Packing, Ammunition for Adapter Boos

6、ter Mi48 or Adapter Booster M148E1 9272263 - Adapter-Booster, Bomb, Nose, Thermally Protected, M148E1, Loading Assembly (Copies of specifications, standards, drawings and publications required by suppliers in connection with specific procurement functions should be obtained from the procuring activi

7、ty or as directed by the contracting officer.) %For meaning of asterisk see 6.7. 3. REQUIREMENTS 3.1 Material. - Materials shall be in accordance with applicable drawings and specifications. %3.2 Adapter-Booser assemblies. - The assemblies shall comply with all requirements specified on Drawing (dwg

8、. ) 9272263 and associated drawings and with all requirements specified in applicable specifications and standards. 3.3 Sealing of .barrier bag. - When the barrier bag is required, . all included air shall be removed prior to sealing. 83.4 Packing supports. - The packing supports when made of molded

9、 polystyrene foam, shall not contain moisture in excess of 0.4 percent, shall not exhibit an electrical potential in excess of 600 volts when rubbed with a rayon or silk cloth, and shall Be self extingui8hing (2lanimab.ility) in accordance with Standard ASTM-Pl692, 3.5 Workmanship. - All parts and a

10、ssemblies shall be fabricated and finished in a thorough workmanlike manner and all manufacturing, processing, and assembly operations shall be correctly performed. They shall be free of burrs, chips, sharp edges, cracks, crazes, unblended radii, porosity, 2 Provided by IHSNot for ResaleNo reproduct

11、ion or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I I rl b ri I- W W 8 m c O a u a G o 3 a, h ri P m m 4 ci a, rn O O ci a, -!J a - 2 2: O W u ;r o 3 NNN a33 Cu MMM MMM M . . O00 LnLnLn O ridri d

12、 m o a, k Q m a, u a, ho Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-/-. 4 pi u 2 Cu O co * I 4 H x Jl E Id4 c dl c s n 0 Y W Z O F k 4 3 rn U 1 ! r

13、i 2 m a u ?! K W I z I- x u z % - c, ri w i3 w k O h ri P m 2 O - ci O .ri 7-l Pi h P A :9 4= hoho cc .ri .ri am cdo Ori MIL-A-48027A 33 m 9777706 0335533.7 m ri cd 3 m z Cu Cum Ln M MM M k? O * O k?k? O0 *=I- O0 k? O O ri am O0 cdri E cio mo ci ; O2 k a w 2 b Provided by IHSNot for ResaleNo reprodu

14、ction or networking permitted without license from IHS-,-,-MIL-A-48027A 13 777770b 0315514 O i- I rl 5 rl I- ! .r v) N =3- =3- 8 6 8 W I- z L- 0 a E a x W * (3 8 E U - “(UN Ln MMMM M . k-%RlR-R ER O000 O *=i-* O O000 ri a a, Llr 5 c) o ri o a k O O Dl k O ri cdl rnl 3 i : L P J Y 4 ? i k 8 C Provide

15、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 ri ho c *ri m O d U O .P k O .ri ci pi h rl P Q, m m 4 ho c *rl a cd O 4 - NIL-A-48027A 33 W 7797706 0335535 2 I ri cd 3 m .ri 3 (u M MMM . . Ln M e wwe w o o00 O * *a* O o 000 ri . . d cd c ci a, -ci, z O v

16、) M u- a Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-4B027A 13 7777706 0315516 4 W ri I- W W 2 V) I ! .=I- . ;Cu =I- :. 1 * rl ri ri rlrl d d cd cdd 5 5 55 2 m m mm $ 2 3 5% Cu Cu Cu Cum M M M MM . = N O O =a- =$ = tRtR m mo D wo . O O o or

17、l Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-8 H E- u w pi u1 t .z E fr! c C P 2 C c 3. E t U c + 0 n 4 Pi 4 c- Cu O co 3 I 4 I 4 H z v v Y k I= oll I- rn 2 ta 8 U W Z O F k 4 rn rn 4 U ri I& O rl ki W I Lo MIL-A-4027A 13 777770b 0315517 b ri cd

18、 ? Ln M 69XXW X w O000 o O =l-=I-=l-=r =I- O . O000 o ri k a, .ri ci k cd P cd E 4: k k O O A k O a, 0 a d P w 2 ri cdl ai 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-qB027A 33 777770b 0335538 ri 0 6 ? Ll L . o U E 2 $ c 11 Provided by I

19、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-,- 4 Pi L cc N O co =r I 4 I d H x 12 I ri Li O ri k a, .P v) O O a rn .P a, ri ri a, Pi MIL-A-48027A 13 MFF70b 0315519 T M cucucucu Ln M MMMM ke O O rl NkeMke O000 =t=T=t=t O000 a .ri k a, a a, c O z 2 A .ri m ci O

20、 O A k O a, o a .ri w $ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I flIL-A-LI8027A 13 W 7977706 0315521 B E MIL-A-48O27A (PA) this specification

21、is identified in the Paragraph Reference/ Inspection Method column in the tables stapting with paragraph 4.4.2.1, and the test method paragraphs (see 4.5). The contractor shall submit for approval, inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-4807

22、8, and 603 herein. 84e 5.1 Moisture content of packing support s4.5.1.1 Preparation of specimen. - The total weight of the specimen shall weigh approximately one hundred (100) grams . The specimen shall consist of pieces or sections that are removed sequentially from the sample to yield the maximum

23、specimen weight and size that the test flask can accommodate. The cutting of the support to obtain the specimen shall not be accomplished by use of heat such as hot wires, heated knives, etc. A knife with a serrated edge has been found to be adequate for this purpose. The specimen shall be weighed t

24、o the nearest 0.1 gram. tion, and techniques apparatus prescribed in ASTI4 D2044 shall be observed. Place 1,200 milliliters of dry (suitably distilled) toluene into the test flask. Add the specimen to the flask and assemble the cover as soon as the specimen is in place. A maximum of five (5) minutes

25、 is allowed from the time when the insert is removed from the polyethylene bag to the time when the cover is assembled to the test flask. If this time period is exceeded, discard the contents of the test flask, the test shall not be completed, and a replacement insert and a specimen shall be selecte

26、d and prepared, adhering to all of the requirements for selecting and preparing the original sample and specimen. The toluene solution contain- ing water from the specimen shall be refluxed by the appli- cation of heat to the test flask until the water level in the distillation trap maintains a cons

27、tant level for i5 minutes minimum. The system shall then be allowed to cool to ambient temperature. Then, 40 to 50 milliliters of toluene, in 10 milliliter increments, shall be poured down the condenser to rinse any water droplets from the surface. The distillation trap shall then be removed from th

28、e system, its contents stirred to assure conlplete separation of the toluene and water. The volume of the water shall be observed and recorded 4.5.1.2 Test procedure. - In general, the precautions, calibra- 14 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

29、IHS-,-,-MIL-A-48027A 13 9999906 0335522 T 9 MIL-A-48027A (PA) as V, estimated to the nearest 0.05 milliliter, The total percentage of moisture content shall be calculated as follows: Percentage of moisture content = 100 V W where : V = Volume of water, in miliiliters. W = Weight of the specimen, in

30、grams. “4*5.2 Static potential charge, - The support shall be .removed from the polyethylene bag, placed on an ungrounded surface, in an environment of nab more than 55 percent reliative humidity, and briskly rubbed with a rayon or silk cloth, not less than 25 strokes for a distance of 8 inches mini

31、mum, each stroke superimposed upon the preceeding stroke, The cloth used in this test shall be of a size and so arranged that there is no possibility of Ghe operators hand touching the support during the te&. The support shall not be touched in any manner during this induction period or during the m

32、easurement which shall follow immediately after the last stroke of holding the detecting head of a Keithley Static Meter No. OOB, with detecting head No, 2501 (or substantial equals) not more than 3/8 inch from the approx- imate center of the support surface where 6he rubbing was accomplis he d. NOT

33、E: adherence to manufacturers recommended procedures, including calibration and heat standoff distances, Special atten-bion should be given to preventing disturbance of the coaxial cable between the detector head and the electrometer during test when using the Keithley equfpment . as prescribed -E i

34、n ASTM D1 92 from each of the supports on the sample and tested as specified therein. conditioning an testing shall be as prescribed In ASTM D1692. Static potential charge measurements require sixingent a4.5.3 FPammabiiit . - One specimen shall be prepared The specimen size, “4.5.4 gravfty shall be

35、determined in accordance with ASTM Method D-792 Method A-1, Specific Gravity - Boaster Pellek. - The specific Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-A-48027A 13 W 7779906 0335523 1 W MIL-A- 4 8 O 2 713 (PA) 5o PREPARATION FOR DELIVERY.

36、 5.1 Preservation and Packaging W5.l.l Level A. - Preservacion and packing shall be as specified on dwg. 9270711. 6, NOTES 36.1 Intended use. - The Adapter-booster covered by this specification is intended for use in the m80 series bombs. 86.2 Ordering data. - Procurement documents shall specify the

37、 following : I a. Title, number and date of this specification. b. Provisions for submission of first article samples. e. Provisions of MIL-A-48078. s6.3 Submission of Inspection Equipment Designs for Approval, (See MIL-A-48078). Submit equipment designs as required, to Commander: Picatinny Arsenal,

38、 ATTN: SARPA- &A-T-T, Dover, New Jersey 07801. s6.4 Distribution of ammunition data cards. - Distribution of data cards shall include the following: Comma.nder, Picatinny Arsenal, ATTN: SARPA-&A-A-M, Dover, New Jersey 07801. Asterisks - 6.7 The margins of this specification are marked with as asteri

39、sk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was hone as a convenience only and the Government assumesno liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requ

40、ire- ments of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Cus t odian : Army-PA Project Number: 1325-A-463 Preparing Activity: Army-PA *US. GOVERNMENT PRINTING OFFICE: 1976-603-767/320 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-