NAVY A-A-50386-1991 GLOVES MEN-S AND WOMEN-S《男女式手套》.pdf

《NAVY A-A-50386-1991 GLOVES MEN-S AND WOMEN-S《男女式手套》.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-50386-1991 GLOVES MEN-S AND WOMEN-S《男女式手套》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-503b 4 = 9999974 0060354 T 1ss COMMERCIA INCH-POUND A-A-50386 13 March 1991 ITEM DESCRIPTION GLOVES, MENS AND WOMENS This Commercial Item Description is authorized for use in preference to MIL-G-24909. Description - The gloves shall be slip on style with sewn in bolton thumb and shall have one p

2、iece fourchettes, top opening with turned under hem and a cut and sewn fabric liner. The thread used for stitching shall be of any commercial type suitable for the purpose intended. The color of the thread used for stitching the leather shall be black, approximating the color of the leather and the

3、color of thread used for stitching the liner shall be natural. When stitching the liner finger tips to the shell finger tips, the stitching shall go over or into the existing stitches at the finger tips. The chain portion of the stitching shall be on the inside of the glove. The stitch type for seam

4、ing, the seam type, stitch gauge and stitch length shall produce adequately durable seams throughout the gloves. Material - The tranks shall be cut from leather conforming to type A, class 2, sub-class b, of KK-L-254. The minimum wet and dry colorfastness shall be Munsell 7.5 (wet) and Munsell 8.5 (

5、dry). The leather shall have a thickness of 1-1/2 to 2-1/4 ounces. Folds or wrinkles more than 1/16 inch wide in the flat are not acceptable. The requirements for total ash, chromic oxide, and pH are not applicable. The leather shall not discolor the water in the shrinkage temperature test. The leat

6、her shall be developed dyed black and shall approximately match shade number 27038 of FED-STD-595. The Color shall be uniform throughout, and shall completely penetrate the leather from the grain side to the flesh side. NOTE: A developed dye is a skin whose color is obtained by the application of a

7、dye, subsequent application of a suitable nitrite, followed by a developer. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Reasearch Facility, P.O.

8、Box 59, Natick, MA 01760-0001 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the .end of this document or AMSC N/A FSC 8440 DISTRIBUTION STATEMENT A. Approved for public release, distribution is / unlimited. Provided by IHSNot for ResaleNo repro

9、duction or networking permitted without license from IHS-,-,- A-A-503b 4 9999974 0060355 II A-A-50386 Fabric liner - The liner shall be made from a plain knit 50% polyester/50% wool (+ 5% for each fiber) fabric. The fabric shall have a minimum weight of 6.0 ounces per square yard and shall have 13-1

10、5 wales per inch and 13-15 courses per inch of a single yarn. The face side of the fabric shall be lightly napped. The color shall be natural or light beige. Recycled, reprocessed, or reused wool or polyester fibers are permitted. Sizes. The gloves shall be of one type only in the following sizes as

11、 specified. 1 - IC - 2 - 2C - 3 - 3C - 4 - 4C - 5 - 5C - 6 - 6C - 7 - 7C - 8 - 9 - 10 NOTE: Cadet sizes have shorter fingers. All sizes are “Unisex“, however, sizes 1 through 3C are graded to accommodate the greatest percentile of women and sizes 4 through 10 are graded to accommodate the greatest p

12、ercentile of men. Label - A commercial type label is acceptable provided that additional printed cloth labels containing the contractors name, contract number and NSN is caught in the stitching of the commercial label. The commercial label may include care instructions and fiber content. Sizes and m

13、easurements - The finished gloves shall conform to the dimensions specified below. All measurements and tolerances are expressed in inches. All measurements shall be taken without distorting the finished glove. Overall Thumb Width Size Length (A) Length (B) (Cl 1 9-3/4 2-3/8 3-318 1c 9-1/2 2-1/8 3-3

14、/8 2 9-7/8 2-1/2 3-1/2 2c 9-5/8 2-1/4 3-1/2 3 10-1/4 2-5/8 3-3/4 3c 10 2-3/8 3-3/4 4 9-5/8 2-3/8 4 4c 9-3/8 2-1/8 4 5 10 2-1/2 4-1/8 5c 9-3/4 2-1/4 4-1/8 6 10-1/4 2-5/8 4-1/4 6C 10 2-3/8 4-1/4 7c 10-1/4 2-1/2 4-1/2 8 10-3/4 2-7/8 4-5/8 9 11 3 4-3/4 10 11-1/4 3-118 4-7/8 7 10-1/2 2-3/4 4-1/2 + 3/16 -

15、 + 1/8 - + 1/4 Tolerance: - NOTE: Refer to Figure 1 for A, B, and C measurements. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5038b 84 = 9999974 0060356 3 W i I A- A- 50 3 8 6 Pairing - The gloves shall be matched, paired,placed palm to pal

16、m and tacked. Tacking shall be done with no less than two stitches, using a suitable ply cotton thread which will permit the gloves to be separated without tearing the leather. Patterns - The government shall furnish a single size pattern. The contractor is responsible for grading patterns for addit

17、ional sizes. The pattern generally provides for a seam allowance of 1/16 to 3/32 for leather to leather seaming operations and 3/32 to 3/16 for liner seaming operations, except to top opening, which allows for a 3/8 to 1/2 inch hem. Commercial patterns may be used in lieu of government patterns prov

18、ided they conform to the cited design and finished measurements. Workmanship - After completion, the gloves shall be thoroughly cleaned and all foreign matter removed. Product demonstration model - Offerers are required to submit two (2) pairs of gloves of their intended production and style. Produc

19、t demonstration models will be analyzed and evaluated by the Government. Evaluation criteria and basis for award are contained in the solicitation. Product demonstration models will be retained by the Government. One (1) product demonstration model approved by DPSC under the resultant contract will

20、serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the product demonstration model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description speclfied abov

21、e. Responsiblity for inspection - The supplier is responsible for assuring the e- product conforms to the requirements. Glove lots will be inspected to determine conformance with the Commercial Item Description and the successful offerers technical proposal negotiated. Acceptability of glove lots wi

22、ll be determined by the use of “Sampling Procedures and Tables for Inspection by Attributes“, ANSI 21.4, published by the American Society for Quality Control. Sampling procedures will be designated by the Government at the time of award. The sample unit is one glove and the selection done in pairs.

23、 The gloves will be examined for commercial type defects. Defect - The gloves shall be examined for the following defects: any hole, cut, tear, needle chew, abraded surface, weak or thin spot, hard scars, brittle or bony area, or deep grain damage; leather shaded throughout the glove; color not as s

24、pecified; any spot or stain (outside); thread ends not removed; stitching of liner finger tips to shell finger tips not as specified; not cut or fabricated in accordance with the product demonstration model; mispaired, i.e., two lefts or two rights; label missing, incorrect, or illegible; measuremen

25、t of item not as specified; and any variation not otherwise classified herein but at variance with the product demonstration model. Preservation - Ten (10) pairs of properly mated gloves of one size only, shall be neatly stacked in a bundle with every .other pair reversed fingertip to cuff. Each bun

26、dle shall be loosely bound around the center with any suitable commercial grade kraft paper. The ends of the paper wrapper shall be either pinned, pasted, or secured with gummed paper tape (1 inch minimum width), or pressure sensitive tape. 3 Provided by IHSNot for ResaleNo reproduction or networkin

27、g permitted without license from IHS-,-,- A-A-50386 84 M 9999974 0060357 5 A-A-50386 Packing - Thirty (30) pairs of gloves, of one size only, preserved as specified above, shall be packed in a fiberboard shipping container assembled, closed and reinforced conforming to type CF, class domestic, grade

28、 200, variety DW, size 1A of MIL-B-17757. The fiberboard for the box liner shall conform to type CF, class domestic of MIL-B-17757. Each package shall be packed flat, three in length, one in width, and one in depth within the shipping container. Two ounces of flaked naphthalene conforming to class B

29、 of R-N-91 shall be evenly distributed throughout the pack. Each container shall have the contents completely covered on top and bottom with a sheet of 30 pound minimum basis weight kraft paper, of any suitable commercial grade. Marking - In addition to any special marking required by the contract o

30、r order, unit packs, intermediate or exterior containers, and palletized unit loads shall be marked in accordance with MIL-STD-129. Palletization - When specified in the contract, gloves packed as specified above, shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD

31、-147. Each prepared load shall be bonded with primary and secondary straps in accordance with the bonding methods C and D or Film bonding F or G. Pallet patterns shall be in accordance with the appendix of MIL-STD-147. The pallet shall be 4-way, type IV; type V, class 1, size 2; or type VIII, fabric

32、ated from wood groups I, II, III or IV, grade A of NN-P-71, or 4-way, style 1, size A, type I, class 1 fabricated from groups specified of MIL-P-15011. Interlocking of loads shall be effected by reversing the pattern of each course. If the container is of a size which does not conform to any of the

33、patterns specified in MIL-STD-147, the pallet pattern used shall first be approved by the contracting officer. Custodians: Navy - NU Army - GL Air Force - 11 Preparing activity: Navy - NU Project 8440-0194 Review activities: Navy - MC Air Force - 82, 99 DLA - CT User activities: Navy - CG Air Force - 45 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-503Bb 84 74 0060358 7 M A-A-5 O 3 8 6 FRONT BACK FIGURE 1 GLOVES, MENS AND WOMENS 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-