NAVISTAR MPAPS A-2-2018 Cold Finished Steel Bars.pdf

《NAVISTAR MPAPS A-2-2018 Cold Finished Steel Bars.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS A-2-2018 Cold Finished Steel Bars.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2018 by Navistar, Inc. JANUARY 2018 Page 1 of 14 NAVISTAR, INC. Material, Parts, and Process Specificati

2、ons (MPAPS) NUMBER: MPAPS A-2 Former Designation: CEMS A-2 TITLE: Cold Finished Steel Bars CURRENT REV No.: 1801 DATE: Jan. 2018 WRITTEN/EDITED BY: W. Cook APPROVED BY: R. Goluch SUPERSEDES: 1706 June 2017 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may i

3、nvolve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. 1.0

4、 APPLICATION Cold finished bars are free from scale, have closer dimensional tolerances, better machinability, and offer improved mechanical properties. They are also more expensive than hot rolled bar products. 2.0 SCOPE 2.1 This specification covers requirements for general applications of carbon

5、and alloy cold finished steel bars. Whenever applicable the specification should be used in conjunction with MPAPS A-0, Part II, Navistar System of Steel Classification. Unless otherwise specified, the appropriate ASTM Specifications shall apply to this specification. 2.2 Requirements for cold finis

6、hed steel bars not included in this specification are in the following Corporate Engineering Materials Specifications: Wrought Corrosion and Heat Resisting Steel MPAPS A-37 HSLA Grade 50 or similar Materials MPAPS A-43 2.3 Restricted Chemical Substances Effective January 1, 2007, all product supplie

7、d to the requirements of this specification must comply with the requirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this

8、specification. ISO 9001/TS 16949 Quality Management Systems- Requirements CFR Title 29, Part 1910 Occupational Health and Safety Standards NAVISTAR ISQ-001-QM Integrated Suppler Quality Requirements NAVISTAR D-13 Supplier Packing and Shipping Standard. NAVISTAR EDS-A16 Key Control Characteristics (K

9、CC) NAVISTAR MPAPS B-50 Restricted Chemical Substances NAVISTAR MPAPS A-0, Part I: Chemical Composition of Standard Steels NAVISTAR MPAPS A-0, Part II: System of Steel Classification for Standard Steels NAVISTAR MPAPS A-43: High Strength Low Alloy (HSLA) Steel Plate/Bar ASTM A29: Standard Specificat

10、ion for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought ASTM A370: Standard Test Methods and Definitions for Mechanical Testing of Steel Products NUMBER: MPAPS A-2 TITLE Cold Finished Steel Bars REVISION: 1801 This document is restricted and may not be sent outside Navistar, Inc.

11、or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2018 by Navistar, Inc. JANUARY 2018 Page 2 of 14 ASTM A108: Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished ASTM A311: Standard Specification for Cold-Dra

12、wn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Property Requirements ASTM A322: Standard Specification for Steel Bars, Alloy, Standard GradesASTM A400: Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical Properties ASTM A434: Standard Specification for Steel B

13、ars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered 4.0 REQUIREMENTS Cold finished bars are classified by chemistry and identified by SAE/ASTM steel grade designation Material supplied shall meet the applicable requirements of ASTM A29, ASTM A108, ASTM A311 and ASTM A322. 4.1 Chemical Co

14、mposition 4.1.1 Bars purchased to this specification shall conform to the required analysis for the appropriate steel in MPAPS A-0, Part I, Chemical Composition of Standard Steels. 4.1.2 Steels with an “SR”, “SS” or “SSA” suffix shall have the same chemical composition as those without a suffix. 414

15、5 SS and 4145 SSA shall meet the chemical composition requirements for SAE 4145, except the carbon content shall be 0.40-0.50 percent with lead, tin, or tellurium additions permissible. 4.1.3 The most readily available cold drawn steels are 1018 and 1045. Effort should be made to standardize on thes

16、e grades. 4.2 Mechanical Properties Mechanical properties for as cold drawn bars are not guaranteed, nor are those for turned and polished or turned, ground, and polished bars which have properties of hot rolled bars. See “Appendix - General Information.”. A useful guide for selecting appropriate ba

17、r stock and processing methods to achieve required properties is found in ASTM A400. Required tensile properties for cold drawn, stress relieved steel bars are shown in Table I. See “Methods of Test,” page 5, and “Appendix - General Information.” NUMBER: MPAPS A-2 TITLE Cold Finished Steel Bars REVI

18、SION: 1801 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2018 by Navistar, Inc. JANUARY 2018 Page 3 of 14 TABLE I MECHANICAL PROPERTY REQUIREMENTS - CO

19、LD DRAWN, STRESS RELIEVED STEEL BARS (Special Cold Drawn, High Tensile) Size, incl Steel Designation International Code MPAPS Part II Rounds, Squares Inches mm Yield strength, elongation 2 in (50.8 mm) psi MPa percent, min 0.375 to 2.000 9.52 to 50.80 1040 SR 2-421 90 000 621 10 1045 SR 100 000 689

20、10 1137 SR 90 000 621 11 1141 SR 100 000 689 11 1144 SR 100 000 689 10 1144 SS * no code 125 000 862 10(1) 1541 SS * 130 000 896 12(1) 4145 SS * 130 000 896 10(1) 4145 SSA * 165 000 1138 9(1) 1.000 to 2.500 25.40 to 63.50 International 50” SR no code 80 000(1) 552(1) 18(1) 2.001 to 2.500 50.82 to 63

21、.50 1137 SR no code 90 000 621 11 1045 SR 2-422 100 000 689 10 1141 SR 100 000 689 11 1144 SR 100 000 689 10 1144 SS* no code 125 000 862 10(1) 4145 SS* 130 000 896 10(1) 4145 SSA* 65 000 1138 9(1) 2.501 to 3.000 63.52 to 76.20 1137 SR no code 90 000 621 10 1045 SR 2-422 100 000 689 10 1141 SR 100 0

22、00 689 10 1144 SR 100 000 689 10 4145 SS* no code 130 000 896 10(1) 4145 SSA* 165 000 1138 9(1) 3.001 to 3.500 76.22 to 88.90 4145 SS* no code 130 000 896 10(1) 4145 SSA* 165 000 1138 9(1) 3.001 to 4.000 76.22 to 101.60 1045 SR 2-422 90 000 621 9 1141 SR 90 000 621 9 1144 SR 90 000 621 9 * If cold d

23、rawn, stress relieved steel bars are ordered in 40 000 lb (18 Mg) minimum quantities, the yield strength shall be held to a maximum of 20 000 psi (138 MPa) over the specified minimum yield strength. * Special Steels. Additional minimum requirements. Steel Tensile Strength Hardness RC Psi MPa 1144 SS

24、 140 000 965 30 1541 SS 150 000 1034 33 4145 SS 150 000 1034 32 4145 SSA 180 000 1241 38 In event of disagreement between hardness and tensile strength, the tensile strength shall govern. (1) Typical value; not a requirement. NUMBER: MPAPS A-2 TITLE Cold Finished Steel Bars REVISION: 1801 This docum

25、ent is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2018 by Navistar, Inc. JANUARY 2018 Page 4 of 14 4.3 Dimensional Tolerances Material purchased to this specificatio

26、n shall conform to the dimensional tolerances in ASTM A108 The diameter tolerances for round bars shown in Table II below and Table IV, page 5, are extracted for convenience. Tolerances for 1144 SS, 4145 SS, and 4145 SSA cold drawn round bars shall be as shown in Table III. See “Appendix - General I

27、nformation” for square, hexagon, and flat bar tolerances. TABLE II - ROUNDS COLD DRAWN AND TURNED AND POLISHED, DIAMETER TOLERANCES, MINUS Heat Treatments and Bar Diameter Carbon Steel Maximum of Carbon Range, Percent, Incl 0.28 and under 0.29 to 0.55 over 0.55 to 0.55 over 0.55 all carbon ranges Al

28、loy Steel Applicable Heat Treatments before cold finishing no heat treatment or anneal, spheroidize anneal, normalize no heat treatment or anneal, spheroidize anneal, normalize quench and temper or normalize and temper For alloy bar tolerances, increase the carbon bar tolerances of similar size, car

29、bon range and heat treatment by 0.001 inch (0.03 mm) after cold finishing None stress relieve or anneal None Bar Diameter, inches, incl Cold Drawn or Turned and Polished, inch to 1.500 0.002 0.003 0.005 0.004 0.005 0.005 1.501 to 2.500 0.003 0.004 0.006 0.005 0.006 0.006 2.501 to 4.000 0.004 0.005 0

30、.007 0.006 0.007 0.007 Turned and Polished Only, inch 4.001 to 6.000 0.005 0.006 0.008 0.007 0.008 0.008 6.001 to 8.000 0.006 0.007 0.009 0.008 0.009 0.009 8.001 to 9.000 0.007 0.008 0.010 0.009 0.010 0.010 9.001 and over 0.008 0.009 0.011 0.010 0.011 0.011 Bar Diameter, mm, incl Cold Drawn or Turne

31、d and Polished, mm to 38.10 0.05 0.08 0.13 0.10 0.13 0.13 38.12 to 63.50 0.08 0.10 0.15 0.13 0.15 0.15 63.52 to 101.60 0.10 0.13 0.18 0.5 0.18 0.18 Turned and Polished Only, inch 101.62 to 152.40 0.13 0.15 0.20 0.18 0.20 0.20 152.42 to 203.20 0.15 0.18 0.23 0.20 0.23 0.23 203.22 to 228.60 0.18 0.20

32、0.25 0.23 0.25 0.25 228.62 and over 0.20 0.23 0.28 0.25 0.28 0.28 TABLE III - ROUNDS COLD DRAWN, 1144, 4145 SS AND 4145 SSA, DIAMETER TOLERANCES, MINUS Bar Diameter, incl 1144 SS 4145 SS TURNED, GROUND, AND POLISHED, DIAMETER TOLERANCES, MINUS Bar Diameter incl Resulfurized Carbon Grades Unheat Trea

33、ted Carbon and Alloy Grades Nonresulfurized Carbon Grades, Heat Treated Carbon and Alloy Grades* inches mm Inch mm Inch mm to 1.500 to 38.10 0.001 0.03 0.001 0.03 1.501 to 2.499 38.12 to 63.47 0.0015 0.04 0.0015 0.04 2.500 to 3.000 63.50 to 76.20 0.002 0.05 0.002 0.05 3.001 to 4.000 76.22 to 101.60

34、0.003 0.08 0.003 0.08 Turned, Ground and Polished Only 4.001 to 6.000 101.62 to 152.40 0.004 0.10 0.005 0.13 6.001 and over 152.42 and over 0.005 0.13 0.006 0.15 * For alloy grades, applies only to quench and tempered, normalized and tempered or any similar double treatment prior to turning. 5.0 QUA

35、LITY Material purchased to this specification shall be manufactured from special quality hot rolled bars, unless otherwise specified. The bars shall be commercially free from injurious defects and shall have a smooth bright surface consistent with the method of cold finishing. 5.1 Methods of Test Pe

36、rform the tensile test according to ASTM A 370. 6.0 QUALIFICATION Engineering qualification of sources is required in advance of production shipments. Samples shall be accompanied by test data certifying that all requirements of the specification have been met. 6.1 Quality Control Plan A Quality Con

37、trol Plan for products supplied to the requirements of this specification will be established by mutual agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as features for management by stati

38、stical process control.* * Other characteristics for inclusion in the control plan may be specified on the engineering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are subjec

39、t to the requirements defined in ISQ-001-QM- NAVISTAR Integrated Supplier Quality Requirements. Suppliers must be compliant with ISO 9001 or TS 16949 and fulfill all AIAG PPAP (Production Part Approval Process) documentation and all approval requirements as indicated in NAVISTAR ISQ-001-QM. 7.2 Appr

40、oval NUMBER: MPAPS A-2 TITLE Cold Finished Steel Bars REVISION: 1801 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2018 by Navistar, Inc. JANUARY 2018

41、Page 6 of 14 Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in materia

42、l, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify NAVISTAR Integrated Supplier Quality (ISQ) of the proposed change(s) by contacting their Navistar Supplier Quality representative or sending an email to ISQ. Test data indicat

43、ing conformance to all requirements of this specification, test samples, and new or amended or updated SDS Safety Data Sheet(s) (formerly MSDS) in accordance with CFR Title 29, Part 1910, shall be submitted with the request for change7.3 Process Control The supplier shall either perform and report r

44、esults of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the quality control manag

45、er of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 8.0 SHIPPING AND HANDLING Shipping and identification shall be in accordance with NAVISTAR Supplier Packing and Shipping Standard D-13. Parts shall be packaged so as to avoid any damage in shipment

46、detrimental to the appearance of the part. 9.0 DESIGNATION ON DRAWINGS 9.1 Drawings In specifying cold finished steels on engineering drawings, it is desirable to allow as many options as possible at the manufacturing level and still insure proper engineering performance. A system of coding steels t

47、o accomplish these objectives was established and is covered in MPAPS A-0, Part II, International system of Steel Classification. It is recommended that this coding system be used whenever possible. See “Choice of Tables” in MPAPS A-0, Part II. for critical parts where the freedom of a code cannot b

48、e permitted, a specific steel grade should be used. Ordinarily, no reference to A-2 is made on the drawing except for steels with special properties. Examples of drawing specifications for cold finished steels are as follows: 2-421, MPAPS A-0, Pt II 1045 SR, MPAPS A-2 2-400, MPAPS A-0, Pt II 1144 SS, MPAPS A-2 9.2 Purchase Orders Material designation on purchase orders should consist of one of the appropriate grades and any special requirements necessary for proper fabrication