MSS SP-102-1989 Multi-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance Characteristics《全回转阀门驱动器的连接法兰和驱动组件的尺寸和性能特点》.pdf

《MSS SP-102-1989 Multi-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance Characteristics《全回转阀门驱动器的连接法兰和驱动组件的尺寸和性能特点》.pdf》由会员分享，可在线阅读，更多相关《MSS SP-102-1989 Multi-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance Characteristics《全回转阀门驱动器的连接法兰和驱动组件的尺寸和性能特点》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、MSS SP-102-1989 Originally approved July 1989 Reaffirmed 2001 Multi-Turn Valve Actuator Attachment Flange and Driving Component Dimensions and Performance C haractenstics Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 12

2、7 Park Street, NE Vienna, Virginia 22180 (703) 281 -661 3 MSS STANDARD PRACTICE SP-102 1 An MSS Standard Practice is intended as a basis for common practice by the manufacturer, the user, and the general public. The existence of an MSS Standard Practice does not in itself preclude the manufacture, s

3、ale, or use of products not conforming to the Standard Practice. Mandatory conformance is established only by reference in a code, specification, sales contract, or public law, as applicable. Dimensions and performance characteristics are shown in both U.S. customary and SI units. American product d

4、imensions are shown in inches with the metric equivalent in purenthesis. The cnoersin fucters ure: Conversion Factor Inches to Millimetres 25.4 Pound Feet to Newton Metres 1.356 Pounds to Kilonewtons .O044 Psi to Newton/ mm2 .O06895 Other standards documents referred to herein are identified by thei

5、r-most recent date of issue that was applicable to this standard at the date of issue of this standard:See Section 2. Any part of this standard may be quoted. Credit lines should read Extracted from MSS SP-102, 1989, with permission of the publisher, the Manufacturers Standardization Society. Reprod

6、uction prohibited under copyright convention unless written permission is granted by the Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. Copyright , 1989 by Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. Printed in U.S.A. 1 MSS STANDARD

7、PRACTICE SP-102 FOREWORD This MSS Standard Practice is based, in part, on IS0 International Standard 5210, Multi-turn Valve Actuator Attachment. It also reflects the common practice of the valve and valve actuator industries in North America today. Therefore, the ratings, sizes, and/or number of fla

8、nge types in the MSS Standard Practice for the North American market may differ from those of ISO. The MSS flange types use the IS0 designation, with the addition of an “A”, to distinguish them as American product. When assembling an actuator to a valve, a user is concerned with performance and mech

9、anical interface. In regards to performance, he needs in part: Adequate output torque for valve breakaway and seating loads, and for dynamic loads at rated flow. A specified speed so closing and opening can be accomplished in a prescribed time. Sufficient power rating of the actuator so the valve ma

10、y be cycled as required. Input power requirements. For mechanical interface, he is concerned in part with: The dimensional mating of the actuators mounting surface to the “valve” mounting flange. The dimensional compatibility of the actuators driving components to the valve stem. 0 Size and location

11、 of electrical and/or pressure connections. 0 Sufficient-space and capability to install and service the actuator This Standard Practice will only concern itself with flange and driving component dimensions and performance characteristics. 11 MSS STANDARD PRACTICE SP-102 CONTENTS SECTION PAGE 1 . SC

12、OPE 1 2 . REFERENCES . i 3 . DEFINITIONS . 1 4 . FLA?!GE SEE I?ES!GNAT:GN . 1 5 . ACTUATOR/VALVE INTERFACE REQUIREMENTS . 1 6 . FLANGE SIZE AND PERFORMANCE . 1 7 . BASIS OF FLANGE PERFORMANCE SELECTION 2 8 . ACTUATOR DRIVING COMPONENTS 3 TABLE 1 . FA MOUNTING FLANGE TORQUE VALUES AND FLANGE DIMENSIO

13、NS . 2 2 . GROUP A . DRIVING COMPONENT DIMENSIONS . 4 3 . GROUP B . DRIVING COMPONENT DIMENSIONS 5 FIGURE 1 . ACTUATOR FLANGE . 1 2 . GROUP A . DRIVING COMPONENTS 3 3 . GROUP A . COMPONENTS . RISING VS . NON-RISING STEMS 3 4 . GROUP B . DRIVING COMPONENTS 5 0 . 111 MSS STANDARD PRACTICE SP-102 O 1.

14、2. O 3. MULTI-TURN VALVE ACTUATOR ATTACHMENT FLANGE AND DRIVING COMPONENT DIMENSIONS AND PERFORMANCE CHARACTERISTICS SCOPE This standard practice is intended to provide a basis for the standardization of multi-turn actua- tor mounting dimensions and performance characteristics necessary for their at

15、tachment to general purpose industrial valves. It covers only those actuators supplied by manufacturers as separate components. 4. REFERENCES ANSI B4.1-1979, American National Standard for Preferred Limits and Fits for Cylindrical Parts. ANSI B17.1-1973, American National Standard for Keys and Keyse

16、ats. IS0 5210-1977, Multi-turn Valve Actuator Attachment. DEFINITIONS 5. Actuator: Any device designed for attachment to general purpose industrial valves in order to provide for the operation of the valve. Motive energy to the actuator can be electrical, pneu- matic, manual, etc., or a combination

17、of these. The movement is limited by travel, torque, thrust, or a combination of these. Multi-Turn Actuator: An actuator which trans- mits a torque to the valve for at least one revolution. Torque: A turning moment transmitted through the mounting flanges and driving components, 6. expressed in Poun

18、ds Foot or Newton Metres. Thrust: An axial force transmitted through the mounting flanges and driving components, ex- pressed in Pounds or Kilonewtons. FLANGE SIZE DESIGNATION Flange sizes are designated by the letters “FA”. The next two digits in the classification represent the bolt circle diamete

19、r, expressed in millimetres, appropriately rounded and divided by ten. As an example, a flange designated “FA30” represents: A) One intended for the American market. B) One with a bolt circle diameter (BCD) (D3) of approximately 300mm (exactly 298.5mm or 11.75 in.). ACTUATORIVALVE INTERFACE REQUIREM

20、ENTS When mating an actuator with a valve flange, the primary features of concern are the bolt pattern, type of bolt, the pilot, the performance (both thrust and torque), and driving component dimensions. Care must be taken in defining the driving components as there are numerous configurations. FLA

21、NGE SIZE AND PERFORMANCE 6.1 bolting) are shown in Figure 1. Typical actuator flanges (tapped or through VALVE FLANG GAP SHOWN FOR PURPOSES ONLY D,(REFER TO 6.2.2 AND 6.2.3) FIGURE 1 - ACTUATOR FLANGE *Refer to 6.2.4. 1 MSS STANDARD PRACTICE SP-102 6.2 The torque, thrust, and flange dimensions for F

22、A mounting flanges can be found in Table 1. 6.2.1 The torque and thrust values listed in Table 1 represent the maximum values which can be transmitted through the mounting flanges and driving components. 6.2.2 The mounting holes (D4) shall be equi- spaced and the hole pattern must straddle the threa

23、ded holes shall be consistent with the strength limitations of actuator material. renter!ine nf the uctuatcr ur?:! the .u!-:e. Depth uf 6.2.3 For cases where the actuator flange design incorporates through bolting (refer to mounting holes (Dq), the diameter of the clearance holes shall provide clear

24、ance consistent with ANSI or IS0 requirements for the bolt sizes listed as D4. 6.2.4 The counterbore in the mounting surface of the valve, corresponding to D2 is mandatory; however, the pilot on the actuator (D2 and H) is optional on IS0 and is required on American products. Dimension D2 refers to b

25、oth the actua- tor and valve flange. Clearance shall conform to ANSI B4.1, Class F7. Flange Type - FA07 FA10 FA14 FA16 FA25 FA30 FA35 FA40 a 6.2.5 Dimension Di provides minimum land area for nuts and bolt heads. The shape of the actuator and valve outside of these areas is optional. 7. BASIS OF FLAN

26、GE PERFORMANCE SELECTION 7.1 In determination of the torque values, shown in Table 1, the following design considerations *c.c. ,Ia?e: IPI-P m A) The stress limits for flange bolting is as follows: Material: ASTM A 449 (equal to or better than) Yield Strength: 92,000 psi min. (less than 1”) 8 1,000

27、psi min. ( 1 ” and larger) Working Stress: 30,000 psi B) Coefficient of friction between mounting flanges is assumed to be 0.3. C) Bolts in tension only; no allowance is made for stresses induced by bolt tightening. O TABLE 1 - FA MOUNTING FLANGE TORQUE VALUES AND FLANGE DIMENSIONS (See Figure 1) Th

28、rust LB 4,500 9,000 25,000 35,000 50,000 75,000 I40.000 230,000 KN Torque LB FT 30 1 O0 400 800 1,200 2,000 4,500 8,500 D, Min. 1N 3.54 4.92 6.89 8.25 11.38 13.50 16.00 18.70 MM (90.0) (125.0) (1 75.0) (209.6) (289.1) (342.9) (406.4) (475.0) IN 2. I66 2.312 3.750 5.000 6.000 7.000 8.500 9.000 (58.7)

29、 (1 27.0) -. - H Max. IN MM .12 (3) .I2 (3) .I6 (4) .I9 (5) .I9 (5) .I9 (5) .I9 (5) .32 (8) No. of q *Refer to text for clarification of alternate clearance hole dimensions. 2 MSS STANDARD PRACTICE SP-102 8: ACTUATOR DRIVING COMPONENTS ,/ 8.1 Some valves require torque and thrust, while others requi

30、re torque only. The geometry of the specific connection design will vary in diameter, thread detail, key size, etc. Care must be taken to properly define the interface details. To simplify the identification of the connection, the driving components are categorized as follows: A) Group A Actuators -

31、 Multi-turn actuators which produce torque and thrust. B) Group B Actuators - Multi-turn actuators which produce torque only. 8.2 Group A Actuators 8.2.1 and torque. Figure 2 illustrates a typical driving component configuration for an actuator which delivers both thrust ACTU ATOR X. I I r FIGURE 2

32、- GROUP A - DRIVING COMPONENTS 8.2.2 Group A actuators can be defined more completely by separating them between applications with non- rising stems and rising stems (See Figure 3). NON-RISING STEM ACTUATOf VALVE FLANGE RISING STEM FIGURE 3 - GROUP A - COMPONENTS - RISING VS. NON-RISING STEMS 3 MSS

33、STANDARD PRACTICE SP-102 Flange FA07 FA10 FA14 FA16 FA25 Type IN .O79 1.10 1.42 1.73 2.35 Dg (MM) (20) (28) (36) (44) (60) (MM) (26) (40) (55) (75) (85) (MM) (25) (40) (55) (70) (90) DX IN 1.02 1.57 2.17 2.95 3.35 L IN 0.98 1.57 2.17 2.76 3.54 8.2.3 The dimensions for Group A driving components can

34、be found in Table 2. FA30 FA35 , FA40 - 3.15 3.94 4.72 (80) ( 100) ( 120) ( 100) ( 150) (175) (1 10) ( 150) ( 1 80) 3.94 5.91 6.89 4.33 5.91 7.09 8.2.3.1 The actuator driving component shall accept a diameter up to and including D6. Even though not a requirement of this standard practice, the drivin

35、g component may accept larger diameters up to Dx. Note that D6 and D, are derived from IS0 5210, while Dx reflects the present American Practice. (235) (264) (175) 6.89 IN 2.36 4.04 6.2 7.1 8.00 For top- entry stem nut For bottom- entry stem nut (MM) (60) (103) (1 57) (179) (203) (MW (60) (80) (1 10

36、) (135) ( 1 50) IN 2.36 3.15 4.33 5.3 1 5.91 8.2.3.2 Dimension D5, Figure 3, shall equal or exceed 1.05 times either valve stem diameter or largest stem attachment. Diameter D5, allows for clearance between rising and non-rotating valve stems and any device intended to restrict the downward travel o

37、f the valve stem. Also, it permits clearance for locking and thrust absorbing devices used with non-rising and rotating stems. 13.0 (330) 12.80 (325) TABLE 2 - GROUP A - DRIVING COMPONENT DIMENSIONS (See Figures 2 and 3) 8.3 Group B Actuators 8.3.1 Multi-turn actuators, which produce torque only, ar

38、e categorized as Group B type. In this application, the valve absorbs thrust (typically through thrust bearings) prior to the actuator. The actuator driving component is normally a keyed bore. 8.3.2 ISO-5210 further classifies the Group B actuators into four types (i.e. Bl-Bq). Since Bi and B3 types

39、 do not represent current practice in America, they are not included in this standard practice. For details on Bi and B3 type, refer to IS0 5210. 8.3.3 applicable to non-rising stem valves. Refer to Figure 4. Further, Group B actuators are defined as Type B2, applicable to rising stem valves, and Ty

40、pe B4, 4 MSS STANDARD PRACTICE SP-102 MIN. GROUP BI TYPE 82 RISING STEM VALVES GROUP B TYPE 04 NON-RI SING STEM VALVES FIGURE 4 - GROUP B - DRIVING COMPONENTS 8.3.4 8.3.4.1 8.3.4.2 products have bore diameters up to Dy. 8.3.4.3 The dimensions for Type B2 and B4 driving components are found in Table

41、3. The driving component for Type B4, Figure 4, shall have a bore diameter up to and including Dy. For Type B2, the driving component may accept larger diameters up to D7. It is intended that new The length of L2 shall be limited so there is no interference between the driving and driven components.

42、 TABLE 3 - GROUP B - DRIVING COMPONENT DIMENSIONS (See Figure 4) 5 Number SP-62001 SP-92001 SP-25-1998 SP-42-1999 SP-43-1991 SP-44-1996 SP-45-1998 SP-51-2000 SP-53-1999 SP-54-1999 S P-55-200 1 SP-58-1993 SP-60-1999 SP-61-1999 SP-65-1999 SP-67-1995 p-fie-! 447 SP-69-1996 SP-70-1998 SP-71-1997 SP-72-1

43、999 SP-73-1991 SP-75-1998 SP-77- 1995 SP-78-1998 SP-79-1999a SP-80-1997 SP-81-2001 SP-82-1992 SP-83-2001 SP-86-1997 SP-87-1991 SP-88-1993 SP-89-1998 SP-90-2000 SP-91-1992 SP-92-1999 SP-93-1999 SP-94-1999 SP-85-1994 SP-95-2000 SP-96-2001 SP-97-2001 S P-98-200 1 SP-99-1994 SP-100-1997 SP-101-1989 SP-1

44、02-1989 SP-103-1995 SP-104-1995 SP-105-1996 SP-106-1990 SP-107-1991 SP-108-1996 SP-109-1997 SP-110-1996 sP-111-2001 SP-112-1999 SP-113-2001 SP-114-2001 SP-115-1999 SP-116-1996 SP-117-1996 SP-118-1996 SP-119-1996 SP-I 20-1997 SP-121-1997 SP-122-1997 SP-123-1998 SP-124-2001 SP-125-2000 S P-126-2000 SP

45、-127-2001 List of MSS Standard Practices (Price List Available Upon Request) Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings Spot Facing for Bronze, Iron and Steel Flanges Standard Marking System For Valves, Fittings, Flanges and Unions Class 150

46、 Corrosion Resistant Gate, Globe, Angle and Check Valves with Flanged and Butt Weld Ends (R 01) Wrought Stainless Steel Butt-welding Fittings (R 01) Steel Pipeline Flanges Bypass and Drain Connections Class 15OLW Corrosion Resistant Cast Flanges and Flanged Fittings Quality Standard for Steel Castin

47、gs and Forgings for Valves. Flanges and Fittings and Other Piping Componets - Magnetic Particle Examination Method Quality Standard for Steel Castings for Valves, Flanges, and Fittings and Other Piping Components - Radiographic Examination Method Quality Standard for Steel Castings for Valves, Flang

48、es, Fittings, and Other Piping Components - Visual Method for Evaluation of Surface Irregularities Pipe Hangers and Supports - Materials, Design and Manufacture Connecting Flange Joint Between Tapping Sleeves and Tapping Valves Pressure Testing of Steel Valves High Pressure Chemical Industry Flanges

49、 and Threaded Stubs for Use with Lens Gaskets Butterfly Valves Pipe Hangers and Supports - Selection and Application Cast Iron Gate Valves, Flanged and Threaded Ends Gray Iron Swing Check Valves, Flanged and Threaded Ends Ball Valves with Flanged or Butt Welding Ends for General Service (R 96) Brazing Joints for Wrought and Cast Copper Alloy Solder Joint Pressure Fittings Specification for High Test Wrought Butt Welding Fittings (R 00) Guidelines for Pipe Support Contractual Relationships Cast Iron Plug Valves, Flanged and Threaded Ends Socket-Welding Reducer Inserts Bronze Gate