GSA RR-F-00625 A-1965 FRAME FILE DRAWER《文档制图框架》.pdf

《GSA RR-F-00625 A-1965 FRAME FILE DRAWER《文档制图框架》.pdf》由会员分享，可在线阅读，更多相关《GSA RR-F-00625 A-1965 FRAME FILE DRAWER《文档制图框架》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、RR-F-00625a (MA-FSS ) June 15, 1965 Revision of Int . Fed. Spec. m-F-00625( MA-FSS) December 18, 1964 INTERIM FEDERAL SPECIFICATION FRAhE, FILE DRAWER This Interim Federal Specification was developed by the Standardization Division, Federal Supply Service, General Services Administration, Washington

2、, D. C. 20406, based upon currently available technical infor- mation. and forward recommendations for changes to the preparing activity at the address shown above, It is recommended that Federal agencies use it in procurement 1. SCOPE AND CLASSIFICATION 1.1 Scope. and desk file drawers. This specif

3、ication covers metal file drawer frames to be used in file cabinets 1.2 Classification. 1.2.1 Type and grade. 1.2.2 Sizes. (See 3.3 and 6.2). 2. APPLICABLE SPECLFICATIONS AND STANDARDS 2.1 The following specifications and standards, of the issues in effect on date of The file drawer frames shall be

4、of one type and one grade. invitation for bids, form a part of this specification. Federal Specifications: PPP-B-566 - Boxes, Folding, Paperboard. PPP-B-585 - Boxes, Wood, Wirebound. PPP-B-591 - Boxes, Fiberboard, Wood-Cleated. PPP-B-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, Naile

5、d and Lock-Corner. PPP-B-636 - Box, Fiberboard. PPP-B-640. - Boxes, Fiberboard, Corrugated, Triple Wall, PPP-B-665 - Boxes, Paperboard, Eletal Stayed (Including Stay Material PPP-B-676 - Boxes, Set-up, Paperboard. UU-P-121 - Paper, Bond and Writing, white and Colored. Federal Standards: Fea. Std. No

6、. 102 - Preservation. Packaging and Packing Levels. I Fed. Std. No. 123 - Marking for Domestic Shipment (Civilian Agencies) THIS DOCUMENT CONTAINS 5 - PAGES. FSC 7520 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RR-F-00625A 75 m 7797774 004023 7 m

7、 m-F-O0625a( GSA-FSF) Military Standards: MIL-STD-lo5 - Sampling Procedures and Tables for Inspection by Attributes. MIL-STD-129 - Marking for Shipment and Storage. 3. REQUIREMENTS 3.1 Material. The frame shall be of steel with a corrosion resistant coating or plating and shall be of sufficient rigi

8、dity to meet the requirements of this specification. The frame shall show no rust when tested as described in 4.5.2. The coating or plating shall not crack or flake off when tested in accordance with 4.5.3. 3.2 Construction and design. The construction shall be such as to assure compliance with the

9、requirements specified herein when examined in accordance with 4.3 and tested in accordance with 4.5. than i14 inch. screwdriver and pliers or by toolless assembly. The frame shall be designed to hold the side rails in a parallel position in a manner that they will not separate from the end supports

10、 when tested in accordance with 4.5.4. wide. for a distance of not less than 2-718 inches on one end, to permit break-off for use of the frame in drawers of various depths. may be from 318 to 314 inch. the notched side rails are not required. When tested in accordance with 4.5.1 the midpoint of the

11、side rails shall not sag more The frame shall be designed for easy assembly, either with the use of a common The side rails shall be 118 2 1/32 inch thick and not less than 112 inch They shall be rounded on the edges to promote sliding of the file folders and shall be notched The notching shall be a

12、t 112 inch intervals, except that the end notch If the frame is designed to telescope for a minimum of 2-718 inches, 3.3 Dimensions. Dimensions of the frames shall be as specified in table I. TABLE I.- Dimensions Height I Width Depth Between Inside I To TOD I aximum I Overa 1 Overall I Between End e

13、dges of side - Size of siae Overall at Bottom at Top Supports. Rails. Adjacent Rails 2 i18 - + 114 Maximum Fully extended to Supports. Inches Inches Inches Inches Inches Inches Minimum L 1/16 Letter 9-318 10 11-718 12-314 26 12 Legal I 9-318 10 I 14-718 I 15-3/h I 26 I 15 3.4 Identification marking.

14、 Each frame shall be marked with the manufacturers name or trademark of such known character that the source of manufacture may be readily determined. 3.5 Workmanship. The frames shall be free from foreign matter, scratches, scuffs, dents, burrs, pits, or any other defects that may affect serviceabi

15、lity. 4. 4.1 Responsibility for inspection. SAXLING, INSPECTION, AND TEST PRWEDURES Unless otherwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. laboratory acceptable to the Government. inspections s

16、et forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified, the supplier may utilize his own facilities or any commercial The Government reserves the right to perform any of the 4.2 Sampl

17、ing. -2- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- RR-F-00625A 75 m 7777774 0040824 7 m RR-F-00625 illegible; improper size, location, sequence, or method of application. Materials Workmanship Any component missing, or damaged. Inadequate appi

18、cation of components such as incomplete closure of container flaps, loose strapping, inadequate stapling. Bulging or distortion of container. -3 - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RR-F-00625A 75 7777774 0040825 O 0 RR-F-O0625a( GA-FSS

19、4.5 Tests. Samples taken in accordance with 4.2.4 shall be tested in accordance with 4.5.1, 4.5.2,4.5.3 and 4.5.4. If the number of defective units in the sample exceeds the acceptance number for tha2 sample, the entire lot represented by the sam le shall be reje,cted. laboratory temperature of 70 F

20、. 2 10 F. and a relative humidity of 50 percent 2 10 percent. An assembled file frame, adjusted to its maximum depth, shall be Place in each folder 500 sheets of bond paper, 8xio+ inches, conforming Any frame in the sample having one or more defects shall be reJ%-Led. Tests shall be performed at a 8

21、 4.5.1 Rigidity test. placed on a hard, flat surface. front to back of the frame. to W-P-121, type III, l7x22-lOOOY 32 pound weight. Eleven hanging file folders shall be equally distributed from Examine for compliance with 3.2. 4.5.2 Corrosion resistance test. All components of a frame shall be lace

22、d in a humidity 8 exposure chamber which is maintained at an ambient temperature of 73 F. 2 2 F. and a relative humidity of 93 percent 3 percent. to test. The chamber shall be constructed so that droplets shall not run or drop on the samples from the moisture accumulated on the ceiling of the chambe

23、r. The samples shall be positioned at an angle of 30 degrees to the floor of the chamber to prevent accumulation of standing moisture on the flat surfaces. The samples shall remain in the chamber for 100 hours. At the end of this time the samples shall be removed fromthe chamber and examined for com

24、pliance vith 3.1. The samples shall not be cleaned or handled excessively prior 4.5.3 Flexure test. A side rail shall be placed in a vise and tightened in a vertical position. The side rail shall be flexed from the initial vertical position to one side through an angle of 90 degrees and then to the

25、other side through an angle of i80 degrees. The internal bend radius shall be 1/2 inch. The side rail shaU then be examined for compliance with 3.1. 4.5.4 Assembly test. a hard, flat surface. conforming to W-P-121, type III, 17x22-1000,32 pound weight, shall be placed on each end of the frame. twent

26、y times allowing the file folders to swing freely. An assembled frame, adjusted to its maximum depth, shall be placed on Three hanging file folders each with 500 sheets of bond paper, 810$ inches, The side rails shall be held near the center and rocked 1/2 to 3/4 inch toward each end Examine the fra

27、me for compliance with 3.2. 5. PREPARATION FOR DELIVERY (For civil agency procurement the definitions and application of levels of packaging and packing shall be in accordance with Fed. Std. 102.) 5.1 Packaging. 5.J.i Level A. 5.1.1.1 Disassembly. The frames shall be disassembled to reduce cubage. T

28、he applicable bolts Packaging shall be level A, B or C as specified (see 6.2). and nuts shall be provided with the frames. 5.1.1.2 Unit packaging. Four complete frames of like description shall be packaged together in a close-fitting box conforming to PPP-B-566, PPP-B-665 or PPP-B-676, 5.1.2 Level B

29、. The frames shall be packaged as specified in 5.1.1. 5.1.3 Level C. The frames shall be packaged in accordance with the suppliers commercial practice. 5.2 Packing. Packing shall be level A, B or C as specified (see 6.2). 5.2.1 Level A. Six unit packages of frames of like description shall be packed

30、 in a close- The box shall be closed and strapped in accordance with fitting box conforming to PPP-B-636, V3c. the appendix to the box specification. packed in close-fitting boxes conforming to PPP-B-585, class 3 , PPP-B-591, class II, PPP-B-601, type III, PPP-B-621, class 2, or PPP-B-640, class 2,

31、grade A. strapped in accordance with the applicable specification or appendix thereto. The gross weight shall not exceed 200 pounds. are overpacked. 5.2.1.1 Additional acking. When specified (see 6.2) the fiberboard boxes shall be over- The boxes shall be closed and Strapping of the fiberboard boxes

32、 will not be required when they -4- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-RR-F-00625A 75 = 7777774 0040826 2 - - RR-F-G0625a( GSA-FSS) 5.2.2 Level B. SLY unit packages of frames of like description shall be packed in a close- fitting box co

33、nforming to PPP-B-636, class-domestic. the appendix to the box specification. The box shall be closed in accordance with 5.2.3 Level C. The frames shall be packed to insure carrier acceptance and safe delivery to destination in containers complying with the rules and regulations applicable to the mo

34、de of transportation, 5.3 Marking. 5.3.1 Civil agencies. In addition to markings required by the contract or order, the gackages and shipping containers shall be marked in accordance with Fed. Std. No. 123. 5.3.2 Military activities. In addition to markings required by the contract or order, the pac

35、kages and shipping containers shall be marked in accordance with MIL-STD-129. 6. NOTES 6.1 Intended use. cabinets and desk file drawers. The drawer frames are intended to be used for hanging folders in file 6.2 Ordering data. Purchasers should exercise any desired options offered herein and procurem

36、ent documents should specify the follovring: (a) Title, number, and date of this specification. (b) (c) Size of frame required (see 1.2 and 3-3). Levels of packaging, packing, and any special marking required (see 5.1, 5.2 and 5.3). (d) Additional packing if required (see 5.2.1.1). 6.3 Transportatio

37、n Description 6.3.1 Wansportation descriptions and minimum weights applicable to this commodity are: Ra il : - Furniture parts, not otherwise indexed by name. Carload minimum weight 20,000 pounds, subject to Rule 34, Uniform Freight Class- ification. B: Furniture parts, not otherwise indexed. Truckl

38、oad minimum weight 20,000 pounds, subject to Rule 115, National Motor Freight Classification. 6.4 Federal specifications do not include all types, grades, .etc., of the commodities indicated by the titles of the specifications, or which are commercially available, but are intended to cover the types

39、, etc., which are suitable to Federal Government requirements. 6.5 It is believed that this specification adequately describes the characteristics necessary to secure the desired material, and that normally no samples will be neeessary prior to award to determine compliance with this specification.

40、If, for any particular purpose samples with bids are necessary, they should be specifically asked for in the invitation for bids and the particular purpose to be served by bid sample should be definitely stated, the specification to apply in all other respects. -5- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-