GMKOREA EDS-T-3502-2008 DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES (VERSION 4 Replaced by GMW3136).pdf

《GMKOREA EDS-T-3502-2008 DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES (VERSION 4 Replaced by GMW3136).pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-3502-2008 DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES (VERSION 4 Replaced by GMW3136).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、GM DAEWOO Auto & Technology EDS Engineering, GM DAEWOO Auto & Technology Standards DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES Do Not Use on New Programs. Being Replaced by GMW3136 EDS-T-3502 ISSUED DATE: 1993. 07. 13 REVISED DATE: 2008. 10. 23 VERSION: 4 (Superceded) EDS-T-3502DOUB

2、LE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES PAGE: 1/3 ISSUED DATE: 1993. 07. 13 REVISED DATE: 2008. 10. 23 VERSION: 4 GM DAEWOO Auto & Technology Note: This standard may be applied only for current project. It is Superceded for all future projects and replaced by GMW3136. 1. PURPOSE Thi

3、s standard aims at specifying measure double image condition of the front windscreen glass (hereinafter called safety glass) for automobiles to check conformance to requirements of the standard. 2. SCOPE Apply to the safety glass (laminated glass with a high molecular film) for automobiles 3. TEST P

4、IECE(specimen) This test shall be conducted with three samples (products). For all three samples, no portion of the double image of the spot shall go beyond inside diameter line of the ring 4. EQUIPMENT 4.1. Light Box The light box shall be approximately 300300150mm in size and its front face shall

5、be coated with matted black paint. The ring slit and spot on its front shall be equipped with the orange colour filter and illuminated by a suitable light source (see Fig. 1). Fig 1 4.2. Support Fixture The supporting fixture shall be capable of mounting a specimen at the rake angle of a real car, a

6、nd also of rotating or shifting it in horizontal direction and shifting it in vertical direction. 4.3. Dark Room or Dark Place EDS-T-3502DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES PAGE: 2/3 ISSUED DATE: 1993. 07. 13 REVISED DATE: 2008. 10. 23 VERSION: 4 GM DAEWOO Auto & Technology

7、The apparatus shall be set in semi-dark or dark place to enable the tester to find easily the presence of secondary image. 5. TEST PROCEDURE 5.1. Mount the specimen as shown in Fig. 2. Fig 2 5.1.1. Set point G, a point on the sample surface and on the horizontal line OS which passes through spot cen

8、ter “S“, so that distance between S and G is 7.6mm. G“ is a point which, when the sample is installed in the vehicle condition, passes through the drivers visual field, and where a straight horizontal line that is parallel with the vertical center side in the vehicle longitudinal direction intersect

9、s with the sample. 5.1.2. Mount the specimen at the same angle as to the vehicle on the supporting fixture. 5.2. Set the observers eyes around point “E“ on the horizontal line OS. 5.3. Examine whether the secondary image of the spot that passes through the sample and lies at the center of the illumi

10、nating box goes beyond the inside diameter line of the ring. 5.4. Rotate the sample horizontally around “E“, drivers visual field, and move it vertically to examine the secondary image condition in the test area. (See Fig 3.) EDS-T-3502DOUBLE IMAGE SEPARATION TEST OF SAFETY GLASS FOR AUTOMOBILES PAG

11、E: 3/3 ISSUED DATE: 1993. 07. 13 REVISED DATE: 2008. 10. 23 VERSION: 4 GM DAEWOO Auto & Technology Fig 3 6. TEST CONDITIONS The test area shall be the rectangular defined by the following lines from G: 100mm both upwards and downwards, 250mm towards the drivers side and 500mm towards the front passe

12、nger side. However, the entire portion within 150mm from all edge of the glass shall be excluded from test area. 7. EVALUATION OF TEST RESULT All three test samples shall meet the requirements in Table 1. Those for laminated glass A and B, however, do not apply to the front windscreen glass. Table 1

13、 Type Movement of secondary image Laminated glass A Laminated glass B Partial tempered glass No portion of the double image of the spot shall go beyond inside diameter line of the ring. 8. REFERENCES KS L 2007 Test of safety glass for automobiles ISO 3538 Secondary image separation test MVSS 205 Double image method (test No.15)