FORD WSS-M99P14-A5-2011 PAD PRINTING PLASTIC or PAINTED PLASTIC PROTECTED EXTERIOR or UNDERHOOD TO BE USED WITH FORD WSS-M99P1111-A 《垫料印刷 塑料或涂装塑料 受保护的外部或发动机舱 与福特WSS-M99P1111-A .pdf
《FORD WSS-M99P14-A5-2011 PAD PRINTING PLASTIC or PAINTED PLASTIC PROTECTED EXTERIOR or UNDERHOOD TO BE USED WITH FORD WSS-M99P1111-A 《垫料印刷 塑料或涂装塑料 受保护的外部或发动机舱 与福特WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M99P14-A5-2011 PAD PRINTING PLASTIC or PAINTED PLASTIC PROTECTED EXTERIOR or UNDERHOOD TO BE USED WITH FORD WSS-M99P1111-A 《垫料印刷 塑料或涂装塑料 受保护的外部或发动机舱 与福特WSS-M99P1111-A .pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 12011 05 26 Revised Corrected para number ref. in 3.3.9 A. Reaume, FNA2009 03 05 Activated A. Reaume, FNAPrinted copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 1 of 5 PAD PRINTING, PLASTIC or PAINTED PLASTIC, W
2、SS-M99P14-A5 PROTECTED EXTERIOR or UNDERHOOD 1. SCOPE This specification defines the performance requirements for pad printing on all Ford Motor Company non class A surfaces located underhood or in protected exterior. Protected exterior is defined as an area where there is very low or no UV exposure
3、. 2. APPLICATION This specification was released originally for pad printing using ink for graphics on globally designed radiator caps. The pad printing process is an ink system which is transferred onto the surface of the part. 2.1 Engineering Drawing Ink supplier and corresponding product codes, c
4、olor codes, and number of hits must be documented on the engineering drawing following the performance specification number. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. All parts must also meet the appropriate DVP & R and Subsystem Desig
5、n Specification requirements. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 SYSTEM COMPONENTS 3.2.1 Substrates Plastic and painted plastic as specified on Engi
6、neering Documents. 3.2.2 Substrate Condition The surface to be pad printed must be cleaned by an automated process to ensure the absence of oil or alkaline residues, fingerprints, corrosion, mold release agents, dirt, moisture, and other foreign materials. 3.2.3 Finished Parts Testing must be conduc
7、ted on actual production parts. Where part dimensions limit equipment access, representative panels run through the production processes may be substituted for production parts. If regrind is used, testing at the maximum loading level is required and must meet the specification requirement. These pa
8、nels shall be processed together with parts and shall be representative of the parts with respect to substrate, paint, and processing. ENGINEERING MATERIAL SPECIFICATIONWSS-M99P14-A5Copyright 2011, Ford Global Technologies, LLC Page 2 of 5 Printed copies are uncontrolled When panels are used as a su
9、bstitute, this must be clearly reported on the PSW or the laboratory test report. 3.2.4 Ageing Test specimens prepared for investigations according to this specification must be aged at least 72 hours at 23 +/- 2 C prior to testing. 3.2.5 Process/Product Validation Test Requirements as listed in Tab
10、le 1. This table is for only Approved paint technologies as shown on Ford Approved Source List otherwise full WSS-M99P14-A5 specification testing is required. Design Verification Testing (DV) is done on plaques by the ink supplier. Product/Process Validation Testing (PV) is done on production painte
11、d parts. 3.2.6 GENERAL ACCEPTANCE CRITERIA Initial The graphic ink shall be legible and free of blisters, wrinkles, ragged edges, and any other surface imperfections that will make them unsuitable for the intended usage. The color shall be as specified on the engineering drawing. After Exposure Afte
12、r each of the exposure conditions described in the requirements the ink graphics must not show visual evidence of peeling, loss of printing or legibility, loss of adhesion, staining, blistering, checking, cracking, excessive shrinkage, or any other effect which would detract from its proper function
13、 or appearance. 3.2.7 PRINT ADHESION Place a strip of 25 mm wide 3M #898 or current equivalent tape on the ink. Apply the tape with moderate thumb pressure to the ink and substrate. Remove the tape by pulling one end at a 90 angle with a quick snap. There shall be no effect on legibility and no grap
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM99P14A52011PADPRINTINGPLASTICORPAINTEDPLASTICPROTECTEDEXTERIORORUNDERHOODTOBEUSEDWITHFORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-754326.html