FORD WSS-M99C125-A1-2009 ADDITIVE CERIUM BASED FOR USE WITH DIESEL PARTICULATE FILTERS TO BE USED WITH FORD WSS-M99P1111-A 《柴油机用颗粒过滤器用铈基添加剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSS-M99C125-A1-2009 ADDITIVE CERIUM BASED FOR USE WITH DIESEL PARTICULATE FILTERS TO BE USED WITH FORD WSS-M99P1111-A 《柴油机用颗粒过滤器用铈基添加剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M99C125-A1-2009 ADDITIVE CERIUM BASED FOR USE WITH DIESEL PARTICULATE FILTERS TO BE USED WITH FORD WSS-M99P1111-A 《柴油机用颗粒过滤器用铈基添加剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 11 18 N-STATUS No known use. No replacement named D. DiGregorio, NA 2003 11 20 Revised Updated format 2002 07 25 Activated J. Bennett Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, Inc. Page 1 of 3 ADDITIVE, CER

2、IUM BASED FOR USE WITH DIESEL WSS-M99C125-A1 PARTICULATE FILTERS NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a cerium based automotive diesel fuel additive to be used in association with the fitment of diesel particulate filter after treatment systems. 2. APP

3、LICATION This specification was released originally for materials used for initial fill. This material is also suitable for service use. The material is intended for on-board vehicle dosing systems. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part produc

4、ers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 PHYSICAL/CHEMICAL PROPERTIES 3.2.1 Density 1.11 kg/litre 3.2.2 Viscosity 2 10 MPa (Brookfield at 25 C) 3.2.3 Cerium Concentration 25.0 +/- 0.5 wt. % 3.2.4 Flash Point, min 70 C (ASTM D 93) 3.3 COLOR

5、 The material may be dyed in accordance with supplier standard practice to a color agreed with Ford Motor Company. ENGINEERING MATERIAL SPECIFICATIONWSS-M99C125-A1 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, Inc. Page 2 of 3 3.4 VERIFICATION The affected Materials Engin

6、eering activity reserves the right to conduct verification testing. If the test results do not support the originally submitted data, the supplier must re-test the product in coordination with the affected Materials Engineering activity. This re-test must be conducted and certified by a mutually agr

7、eed upon test facility. 3.5 CHEMICAL AND PHYSICAL PROPERTIES Supplier shall furnish appropriate chemical and physical properties as required on Supplement A along with the manufacturing limits that apply to the material upon which approval is requested. 4. GENERAL INFORMATION The information given b

8、elow is provided for clarification and assistance in meeting the requirements of this specification. 4.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing Engineering Department or other responsible activity shall notify both the Security and Safety Units of its presen

9、ce to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notifications. 4.2 SAMPLING AND SUBMISSION OF SAMPLES (ISO 3170/3171, ASTM D 4057/D 4177) Quality Control records must be made available to Fuels and Lubricants Engineering upo

10、n request. Where applicable, the required tests shall be conducted in accordance with the most recently approved procedures and the applicable ASTM Standards, Research Reports and Information. All tests under surveillance by ASTM must be conducted using test equipment monitored by and calibrated to

11、the requirements of the ASTM Test Monitoring Center. ENGINEERING MATERIAL SPECIFICATIONWSS-M99C125-A1 Printed copies are uncontrolled Copyright 2009, Ford Global Technologies, Inc. Page 3 of 3 (Supplement A, p. 1 of 1) Manufacturer_ Date_ Product Name_ Blend Location _ Product Code_ Specification Test Mfg. Physical/Chemical Properties Requirements Results Limits Viscosity at 40 C (Brookfield at 25 C), mPa.s 2.0 10.0 _ _ Density (ISO 3675 / ASTM D 1298), kg/L 1.11 _ _ Flash Point (ASTM D 93-99c), C min 70 _ _ Cerium (ISO 14596 / ISO 24260), wt.% 25.0 +/- 0.5 _ _ Signature_ Title_