FORD WSS-M4P13-A-2014 ANODIZED ALUMINUM PERFORMANCE DECORATIVE EXTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M4P13-A-2014 ANODIZED ALUMINUM PERFORMANCE DECORATIVE EXTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M4P13-A-2014 ANODIZED ALUMINUM PERFORMANCE DECORATIVE EXTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A .pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 2 2014 06 12 Editorial Corrected suffix 2014 06 10 Updated See Summary of Revisions G. Eaton, NA 2011 10 10 Activated G. Eaton, FNA Controlled document at www.MATS Copyright 2014, Ford Global Technologies, LLC Page 1 of 6ANODIZED ALUMINU
2、M PERFORMANCE, DECORATIVE EXTERIOR TRIM WSS-M4P13-A 1. SCOPE This specification defines the minimum durability and performance requirements of anodized aluminum for bright decorative trim components. 2. APPLICATION This performance specification was released originally for anodized aluminum outer be
3、lt moldings. 2.1 LIMITATIONS Any cleaning agent containing a combination of ethoxylated C12-15 fatty acid and sodium metasillicate should not be used to clean this material (example: Motorcraft Multipurpose Cleaner). Surface attack will occur leaving a chalky substance on the surface. 3. REQUIREMENT
4、S 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 ANODIZED ALUMINUM PERFORMANCE MANAGEMENT All materials evaluated under this performance specification must have
5、 Supplement A completed and signed by Ford Materials Engineering, the material/coatings supplier, and the Tier One supplier. The Supplement A and specification data will be stored in the Ford Materials Database (FMD). If the aluminum is being applied to an outer belt molding, compatibility of the an
6、odized aluminum with seal material (s) is the responsibility of the Tier One supplier. The Tier One supplier shall have the seal tested against the applicable performance specification requirements. Table 2.0 describes the construction of the anodized aluminum, and must be submitted with Supplement
7、A. (Reference Supplement A). The Tier One supplier is responsible for including Table 2.0 and this performance specification on the part drawing. 3.3 FINISHED PARTS Testing must be conducted at Design Verification (DV) and Product Validation (PV) per Table 1.0 (including Supplement A), unless otherw
8、ise agreed to by Materials Engineering, and on actual production parts or a section of the part whenever possible. Where part dimensions limit testing equipment access, representative test samples may be substituted. PV Testing must be conducted on actual production processed parts. No change in mat
9、erial, facility, or processing is permitted without written approval from Ford Materials Engineering Activity, via SREA. ENGINEERING MATERIAL SPECIFICATION WSS-M4P13-A Copyright 2014, Ford Global Technologies, LLC Page 2 of 6 All test values are based on parts conditioned in a controlled atmosphere
10、of 23 +/- 2 C and 50% R.H. for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. 3.4 APPEARANCE: COLOR, FINISH, SURFACE (FLTM BI 109-01) The color, gloss, and finish of the anodized aluminum part shall be specified on the engineering drawing and be
11、uniform along the entire length of the assembly. The surface shall be free of blisters, voids and scratches. 3.5 RESISTANCE PROPERTIES Paragraph 3.5.1 Corrosion Resistance, shall be tested on whole parts or sections of assemblies and must include all materials and interfacing parts (i.e. mating part
12、s). Separate specimens are required for each test. The parts after being subjected to the tests listed below shall conform to the following requirements in addition to the ones listed: (a) No cracking, chalking, crazing, iridescence, bloom, milkiness, separation, loss of adhesion (coating), or loss
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM4P13A2014ANODIZEDALUMINUMPERFORMANCEDECORATIVEEXTERIORTRIMTOBEUSEDWITHFORDWSSM99P1111APDF
链接地址:http://www.mydoc123.com/p-753854.html