FORD WSS-M3H195-A1-2017 CARPET POLYESTER 195 PATTERN NON WOVEN RANDOM VELOUR NEEDLED LATEX BACKING 475 g m2 (14 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M3H195-A1-2017 CARPET POLYESTER 195 PATTERN NON WOVEN RANDOM VELOUR NEEDLED LATEX BACKING 475 g m2 (14 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M3H195-A1-2017 CARPET POLYESTER 195 PATTERN NON WOVEN RANDOM VELOUR NEEDLED LATEX BACKING 475 g m2 (14 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 00 2017 07 17 Released L. Wu, AP Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 4 CARPET, POLYESTER, 195 PATTERN, NON WOVEN, RANDOM VELOUR, WSS-M3H195-A1 NEEDLED, LATEX BACKING, 475 g/m2(14 oz) NOM

2、INAL FACE 1. SCOPE The materials defined by this specification are random velour, non-woven carpets of good quality and uniform composition. The face fiber is virgin polyester and it is back coated with the appropriate weight of Latex. 2. APPLICATION This specification was originally released for 20

3、18 MY Ford Everest Load Floor. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of appr

4、oved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity.

5、 Testing of the material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 In addition to the requirements listed herein, the end-item carpet shall be tested to WSS-M8P16-B and any additional SDS requirements. The details for each of the supplier spec

6、ific constructions shall be documented in the supplement attached and uploaded into the scanned data package. 3.3.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1. Data m

7、ust be provided at the appropriate program milestone. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods (including substrate layers) prior to any subsequent operations, such as molding. 3.5 APPEARANCE The color, pattern, and gloss shall match th

8、e approved Corporate Design master sample. ENGINEERING MATERIAL SPECIFICATIONWSS-M3H195-A1Copyright 2017, Ford Global Technologies, LLC Page 2 of 4 3.6 COMPOSITION 3.6.1 Face Fiber 95% Polyester (ASTM D276) 3.6.2 Binder Fiber 5% Low Melt Polyester (ASTM D276) 3.6.2 Primary Backing Latex (ASTM D276)

9、3.7 METHOD OF DYEING Solution dyed 3.8 CONSTRUCTION 3.8.1 Face Fiber 12 Denier (ASTM D 1244) 3.8.2 Binder Fiber 4.5 Denier (ASTM D 1244) 3.9 THICKNESS 3.9.1 Face Fiber Thickness 4 +/- 0.5 mm (ISO 1765) 3.9.2 Secondary Thickness Report mm (ISO 1765) 3.10 WEIGHT 3.10.1 Face Fiber 406 - 496 g/m2(ASTM D

10、5848) (12.0 14.6) oz 3.10.2 Binder Fiber 22 26 g/m2 (ASTM D5848) (0.7 0.8) oz 3.10.3 Secondary Backing Report g/m2 (ASTM D5848) (Report) oz Weight tolerances approved for each suppliers construction can be found in the scanned data package. 4. GENERAL INFORMATION This information given below is prov

11、ided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRAWING CALL OUT The following shall be called out on the Engineering drawing to correctly designate the approved material. WSS-M3H195-A

12、1 Supplier Name and Product Code (As it appears on the Approved Source Listing) WSS-M8P16-B ENGINEERING MATERIAL SPECIFICATIONWSS-M3H195-A1Copyright 2017, Ford Global Technologies, LLC Page 3 of 4 4.2 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expressi

13、on of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of

14、the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with For

15、d. 4.3 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specificat

16、ion requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Eng

17、ineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.4 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulati

18、ons or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS an

19、d or GMAP reporting. 5. SUMMARY OF REVISIONS ENGINEERING MATERIAL SPECIFICATIONWSS-M3H195-A1Copyright 2017, Ford Global Technologies, LLC Page 4 of 4 Non Woven Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product/ Style Name _ Material Specification _ Performance Specific

20、ation _ Supplier Product Code _ Manufacturing Location _ Supplier Lab Number _ Supplier Lab Date _ Composition Type Supplier Face Fiber ASTM D276 _ _ Binder Fiber ASTM D276 _ _ Fabric Backing ASTM D276 _ _ Pre Coat ASTM D276 _ _ Primary Backing ASTM D276 _ _ Secondary Backing ASTM D276 _ _ Construct

21、ion Solution or piece dyed (circle one) % Recycled (PIR/PCR) _ Denier _ Filament Count _ Face Fiber Thickness ISO 1765 _+/- _ mm Binder Fiber Thickness ISO 1765 _+/- _ mm Pre Coating Thickness ISO 1765 _+/- _ mm Primary Thickness ISO 1765 _+/- _ mm Secondary Thickness ISO 1765 _+/- _ mm Mass per Unit Area WeightFace Fiber ASTM D5848 _+/- _ g/m2Binder Fiber ASTM D5848 _+/- _ g/m2Pre Coating ASTM D5848 _+/- _ g/m2Primary Backing ASTM D5848 _+/- _ g/m2Secondary Backing ASTM D5848 _+/- _ g/m2Materials Engineering Signature _Date _ Comments _ Rolled Goods _ Molded Product _