FORD WSS-M3H135-B-2011 CARPET POLYESTER NON WOVEN RANDOM VELOUR NEEDLED FUSED BACK 475 g m2 (14 oz) TO BE USED WITH FORD WSS-M99P1111-A 《无纺随机丝绒针刺有融化衬背的475 g m2(14 oz)聚酯地毯 与福特WSS.pdf

《FORD WSS-M3H135-B-2011 CARPET POLYESTER NON WOVEN RANDOM VELOUR NEEDLED FUSED BACK 475 g m2 (14 oz) TO BE USED WITH FORD WSS-M99P1111-A 《无纺随机丝绒针刺有融化衬背的475 g m2(14 oz)聚酯地毯 与福特WSS.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M3H135-B-2011 CARPET POLYESTER NON WOVEN RANDOM VELOUR NEEDLED FUSED BACK 475 g m2 (14 oz) TO BE USED WITH FORD WSS-M99P1111-A 《无纺随机丝绒针刺有融化衬背的475 g m2(14 oz)聚酯地毯 与福特WSS.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 00 2011 10 17 Activated L. Sinclair, NA Controlled document at www.MATS Copyright 2011, Ford Global Technologies, Inc. Page 1 of 3 CARPET, POLYESTER, NON WOVEN, RANDOM VELOUR, WSS-M3H135-B NEEDLED, FUSED BACK 475 g/m2 (14 oz) 1. SCOPE The

2、 material defined by this specification is a needled random velour non woven carpet of good quality and uniform composition. The carpet back is fused for improved abrasion resistance. 2. APPLICATION This specification was released for load floor covering requiring higher heat face goods due to in mo

3、ld application of carpet using a 100 ton press. This material would be utilized when molding temperatures reach 225 F or greater. 3. REQUIREMENTS In addition to the requirements listed herein, the end-item assembly shall be tested to WSS-M8P16-B/latest and any additional SDS requirements. The detail

4、s for each of the suppliers specific construction shall be documented in the supplement attached and uploaded into the FMD (Ford Materials Database) or scanned data package. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

5、 Requirements For Production Materials (WSS-M99P1111-A). 3.1.1 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-C1. Data must be included in material submission package. 3.2 S

6、AMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished assemblies. 3.3 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. ENGINEERING MATERIAL SPECIFIC

7、ATION WSS-M3H135-B Controlled document at www.MATS Copyright 2011, Ford Global Technologies, Inc. Page 2 of 3 3.4 COMPOSITION 3.4.1 Face Fiber 90% Polyester (ASTM D276) UV Resistant 3.4.2 Binder Fiber 10% Low Melt Polyester (ASTM D276) 3.5 METHOD OF DYEING Solution dyed 3.6 CONSTRUCTION 3.6.1 Face F

8、iber 9 Denier Nominal (ASTM D 1244) 3.6.2 Binder Fiber 3.6 Denier Nominal (ASTM D 1244) Denier range approved for each suppliers construction can be found in the FMD (Ford Material Database) or scanned data package. 3.7 THICKNESS 5.5 +/- 1.0 mm (ISO 1765) 3.8 WEIGHT 3.8.1 Face Fiber 428 g/m2 (ASTM D

9、5848) 12.6 (oz) 3.8.2 Binder Fiber 47 g/m2 (ASTM D5848) 1.4 (oz) 3.8.3 Total Fiber 475 g/m2 (ASTM D5848) 14 (oz) Weight tolerances approved for each suppliers construction can be found in the FMD (Ford Material Database) or scanned data package. 4. GENERAL INFORMATION This information given below is

10、 provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 DRAWING CALL OUT The following shall be called out on the Engineering drawing to correctly designate the approved material. WSS-M3H

11、135-B Supplier Name and Product Code WSS-M8P16-B ENGINEERING MATERIAL SPECIFICATION WSS-M3H135-B Controlled document at www.MATS Copyright 2011, Ford Global Technologies, Inc. Page 3 of 3 Non Woven Carpet Construction Supplement Supplier _Supplier Contact Name_ Number _ Product/ Style Name _ Materia

12、l Specification _ Performance Specification _ Supplier Product Code _ Manufacturing Location _ Supplier Lab Number _ Supplier Lab Date _ Composition Type Supplier Face Fiber ASTM D276 _ _ Binder Fiber ASTM D276 _ _ Minimum Recycled Content _ % PIR _ % PCR Construction Solution or piece dyed (circle one) Denier (s) _ Face Fiber Thickness ISO 1765 _+/- _ mm Binder Fiber Thickness ISO 1765 _+/- _ mm Mass per Unit Area Weight Face Fiber ASTM D5848 _+/- _ g/m2 Binder Fiber ASTM D5848 _+/- _ g/m2 Materials Engineering Signature _Date _ Comments _ Rolled Goods _ Molded Product _