FORD WSS-M2C936-A-2010 FLUID WET DOUBLE CLUTCH TRANSMISSION FULL-SYNTHETIC TO BE USED WITH FORD WSS-M99P1111-A 《全合成湿双离合器传动液 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD WSS-M2C936-A-2010 FLUID WET DOUBLE CLUTCH TRANSMISSION FULL-SYNTHETIC TO BE USED WITH FORD WSS-M99P1111-A 《全合成湿双离合器传动液 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M2C936-A-2010 FLUID WET DOUBLE CLUTCH TRANSMISSION FULL-SYNTHETIC TO BE USED WITH FORD WSS-M99P1111-A 《全合成湿双离合器传动液 与标准FORD WSS-M99P1111-A一起使用 》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Ver 3 2010 03 11 Revised See Summary of Revisions M. V. Swain 2008 05 28 Revised Inserted 3.17.1, 3.17.2, 4, 3.22 Revised the Title, 1, 2, 3.4.2, 3.4.4, 3.8, 3.10.1, 3.10.2, 3.14, 3.15, 3.17 Deleted 3.9 Added 3.21 Printed copies are uncontroll
2、ed Copyright 2010, Ford Global Technologies, LLC Page 1 of 4 FLUID, WET DOUBLE CLUTCH TRANSMISSION, FULL-SYNTHETIC WSS-M2C936-A 1. SCOPE The material defined by this specification is a wet double clutch transmission fluid composed of a synthetic base fluid and performance enhancing additives. 2. APP
3、LICATION This specification was originally released for fluid used to provide general lubrication for automatically operated manual transmissions comprising a wet double clutch system. It provides specific frictional characteristics for hydraulic control, and heat transfer. 3. REQUIREMENTS 3.1 STAND
4、ARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 COLOR Dyed Green (Visual) Subsequent batches must be visually consistent with the original sample color. 3.3 MISCIBILITY T
5、EST Material approved to this specification must be miscible with all other approved materials in all proportions. These blends must also meet all requirements of this specification. Miscibility is checked by mixing the material 50:50 and 10:90 by volume with all other approved materials. Heat all m
6、ixtures to 150 +/- 2 C for one hour and then cool to -40 +/- 2 C. No visible deposits or separation shall occur (visual check only). Contamination with any other material not meeting this specification is prohibited. 3.4 VISCOSITY 3.4.1 At 100 C, min 6.4 mm2/s (ISO 3104, ASTM D 445) 3.4.2 At -26 C,
7、max 2,000 mPa.s (DIN 51398, ASTM D 2983) 3.4.3 At -40 C, max 7,500 mPa.s (DIN 51398, ASTM D 2983) ENGINEERING MATERIAL SPECIFICATIONWSS-M2C936-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 4 3.4.4 Shear Stability (Kinematic Viscosity) (CEC L-45-A-99) Visco
8、sity loss at 20h, 100 C, max 3% Used bearing shear loss after run-in period 9 - 13% with reference oil RL 181/6 Viscosity index, min 150 Viscosity loss at 192h, 100 C, max 5% 3.5 POUR POINT, max -60 C (ISO 3016) 3.6 FLASH POINT, min 200 C(ISO 2592) 3.7 COPPER CORROSION, max (ISO 2160) 3 hours room t
9、emperature, max 1a 3 hours 150 +/- 2 C, max 1b 3.8 RUST PROTECTION, 24 hours No rust (ISO 7120, ASTM D 665 Procedure A) 3.10 ANTI-FOAMING PROPERTIES (ASTM D 892/6082) 3.10.1 New oil Foam Tendency Foam Stability at end of 5 min at end of 1 min blowing period settling period Sequence 1, max 20 mL 0 mL
10、 Sequence 2, max 30 mL 0 mL Sequence 3, max 20 mL 0 mL Sequence 4, max 100 mL 0 mL (For Sequence 4 use ASTM D 6082, static foam, 150 C +/- 3 C; 200 ml air/min) 3.10.2 Used Oil (CEC-L48-A-00(B), 140C / 24 hours / 5 liters air per hour) Foam Tendency Foam Stability at end of 5 min at end of 1 min blow
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM2C936A2010FLUIDWETDOUBLECLUTCHTRANSMISSIONFULLSYNTHETICTOBEUSEDWITHFORDWSSM99P1111A 合成 离合器 传动

链接地址:http://www.mydoc123.com/p-752753.html