FORD WSS-M1H1052-A-2011 FABRIC PROTECTION PATTERN WOVEN DOBBY UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《保护模式多臂提花机编织的非层压织物 与福特WSS-M99P1111-A 一起使用》.pdf

《FORD WSS-M1H1052-A-2011 FABRIC PROTECTION PATTERN WOVEN DOBBY UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《保护模式多臂提花机编织的非层压织物 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H1052-A-2011 FABRIC PROTECTION PATTERN WOVEN DOBBY UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《保护模式多臂提花机编织的非层压织物 与福特WSS-M99P1111-A 一起使用》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2011 06 17 Activated Mark Montgomery, FoE Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 1 of 2 FABRIC, PROTECTION PATTERN, WOVEN DOBBY, WSS-M1H1052-A UNLAMINATED 1. SCOPE The material defined by this speci

2、fication is a woven dobby polyester face fabric, with embossed protection pattern. 2. APPLICATION This specification was originally released for material used as an interior trim fabric for C346 ST 2012MY using a Tri-Laminate construction with no back coating. 3. REQUIREMENTS In addition to the requ

3、irements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4 as applicable. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 FABRIC CON

4、STRUCTION 3.2.1 Fabric Count, +/- 10 % tolerance (ASTM D 3775) Warp 270 ends/10 cm Weft 180 picks/10 cm 3.2.2 Fabric Weight, +/- 10% tolerance (FLTM BN 106-01) 315 g/m2 3.3 COMPOSITION (ASTM D 629) Fabric 100% polyester 3.4 YARN CONSTRUCTION (ASTM D 1244) Warp 600F144 dtex (air texturised, semi-dull

5、, round) Weft 600F144 dtex (air texturised, semi-dull, round) ENGINEERING MATERIAL SPECIFICATION WSS-M1H1052-A Printed copies are uncontrolled Copyright 2011, Ford Global Technologies, LLC Page 2 of 2 3.5 METHOD OF DYEING Solution Dye or as approved by Materials Engineering 3.6 FINISHED OPERATIONS w

6、ashing drying setting Laminating HF-panel embossing 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 Purchase departments will ensure that both materials defined in this specification and shipped to

7、 any one assembly plant will be produced by one supplier only. 4.2 Global C346ST strategy to use Tri-Laminate constructions in all regions. 4.3 If yarn is locally sourced it must meet the above fabric construction, composition and Yarn construction. The fabric must also meet the requirements of WSS-M8P18-A1/A2/A3/A4 4.4 Base fabric construction is Lux product (WSS-M1H913-A)