FORD WSS-M1A374-A1-2013 STEEL SHEET HOT ROLLED BORON TREATED TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M1A374-A1-2013 STEEL SHEET HOT ROLLED BORON TREATED TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M1A374-A1-2013 STEEL SHEET HOT ROLLED BORON TREATED TO BE USED WITH FORD WSS-M99P1111-A .pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2013 12 16 Released A. Wedepohl therefore, there are no requirements for mechanical properties prior to heat treatment. Incoming mechanical properties can be developed and specified on the part print to facilitate production of a speci
2、fic component (see paragraph 3.6). Yield strength, tensile strength, and elongation are also likely to vary with material thickness and supplier. See paragraph 4.2 for typical incoming mechanical properties. 3.10 MECHANICAL PROPERTIES AFTER HEAT TREATMENT (ISO 6892/ASTM E8M/EN 10002, Longitudinal, 5
3、0 mm gage length, ASTM E10) Mechanical properties after heat treat must be listed and controlled on the Engineering Drawing. The type of heat treatment should also be listed. See paragraph 4.3 for an example. ENGINEERING MATERIAL SPECIFICATION WSS-M1A374-A1 Copyright 2013, Ford Global Technologies,
4、LLC Page 4 of 5 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 INITIAL SUPPLIER APPROVAL BY FORD For initial approval, the su
5、pplier should contact Product Development Materials Engineering to obtain the latest revision of the Sheet Metal Material Specification/Source Approval Process and test requirement checklist. Upon initial technical approval and completion of a functional prove-out (line trial), the material will be
6、added to the Engineering Material Approved Source List (ASL). 4.2 MECHANICAL PROPERTIES PRIOR TO HEAT TREATMENT Typical properties for steel 7 11 mm thick as delivered by the steel supplier are: Yield strength: 310 to 450 MPa. Tensile strength: 450 MPa Total Elongation: 22% 4.3 METHOD OF SPECIFYING
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM1A374A12013STEELSHEETHOTROLLEDBORONTREATEDTOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-751576.html