FORD WSL-M96D35-A-2010 ENERGY ABSORBING COMPOSITE HOLLOW CERAMIC SPHERES WITH BINDER TO BE USED WITH FORD WSS-M99P1111-A 《空心陶瓷球与胶粘剂组成的能量吸收复合材料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSL-M96D35-A-2010 ENERGY ABSORBING COMPOSITE HOLLOW CERAMIC SPHERES WITH BINDER TO BE USED WITH FORD WSS-M99P1111-A 《空心陶瓷球与胶粘剂组成的能量吸收复合材料 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSL-M96D35-A-2010 ENERGY ABSORBING COMPOSITE HOLLOW CERAMIC SPHERES WITH BINDER TO BE USED WITH FORD WSS-M99P1111-A 《空心陶瓷球与胶粘剂组成的能量吸收复合材料 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 06 24 N-STATUS No replacement named C. Mracna, NA 2006 09 13 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.7, 3.8 & 4 1991 09 10 Released NL00 E10150047 L.R. Gullen Printed copies are uncontrolled Copyright 2010, Ford Global Technologies

2、, LLC Page 1 of 2 ENERGY ABSORBING COMPOSITE, HOLLOW CERAMIC SPHERES WSL-M96D35-A WITH BINDER NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is an energy absorbing composite consisting of hollow ceramic spheres of nearly constant diameter bonded together by a polyu

3、rethane type monolithic polymer. 2. APPLICATION This specification was originally released as an impact absorbing material for light truck steering columns. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

4、Requirements For Production Materials (WSS-M99P1111-A). 3.4 CERAMIC SPHERES 3.4.1 Bulk Density 0.448 +/- .02 g/cm3(ASTM D 4180, except 250 mL volumetric flask) 3.4.2 Sieve Analysis, min 96% (ASTM E 276, amount retained on a #7 screen) 3.4.3 Crushing Strength 206 +/- 35 kPa Test Method: Fill a 76 x 7

5、6 x 76 mm punch and die set with 250 mL of spheres, tapping to ensure maximum packing of spheres. Place the top punch gently on the bed of spheres, making sure that it is parallel with the lower punch. Assemble the punch and die set with spheres in a mechanical tester. Load the assembly at a rate of

6、 15 mm per minute. At 9 kg begin reading the load every 0.5 seconds, adding the weight of the upper die punch. Continue measurements through crosshead travel of 9 mm. The packed bed crushing strength is the average load over 9 mm crosshead travel divided by the punch area. Calculate the average valu

7、e of the packed bed crushing strength as follows: C avg. = Average Crush Strength = Sum of Ci/n Where Ci = crush strength of individual samples, kPa N = number of crush tests performed ENGINEERING MATERIAL SPECIFICATIONWSL-M96D35-APrinted copies are uncontrolled Copyright 2010, Ford Global Technolog

8、ies, LLC Page 2 of 2 Calculate the standard deviation of the crush strength as follows: C std. dev. = Square Root (Sum of (Ci -C avg.)2/(n -1) 3.5 BINDER 3.5.1 Density 96.2 +/- 9.62 kg/m3(ASTM D 3574, Test A) 3.5.2 Tensile Strength, min 310 kPa (ASTM D 3574, Test E) 3.5.3 Elongation, min 190% (ASTM

9、D 3574, Test E) 3.5.4 Block Tear Strength, min 790 N/m (ASTM D 3574, Test F) 3.6 COMPOSITE 3.6.1 Composition Binder 33 +/- 5% Spheres 67 +/- 5% Test Method: Place samples in weighted crucibles and reweigh. Place crucibles in muffle furnace at 540 +/- 5 C for 1 h. Cool to 23 +/- 2 C and reweigh crucibles. Compute the % of weight loss (binder) and % of retained weight (spheres). 3.6.2 Flammability (ISO 3795) Burn Rate, max 100 mm/minute