FORD WSK-M99J366-A-2006 ACID CATALYST POLYESTER SYSTEM BAKING EXTERIOR TOP COAT TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部面漆用烘烤型聚酯系统用酸性催化剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD WSK-M99J366-A-2006 ACID CATALYST POLYESTER SYSTEM BAKING EXTERIOR TOP COAT TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部面漆用烘烤型聚酯系统用酸性催化剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD WSK-M99J366-A-2006 ACID CATALYST POLYESTER SYSTEM BAKING EXTERIOR TOP COAT TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部面漆用烘烤型聚酯系统用酸性催化剂 与标准FORD WSS-M99P1111-A一起使用 》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 03 23 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.4, 3.11, 4 2000 11 28 Revised Updated & Revised para 3.3 A. Cockman 1990 02 01 Released C01031532 C. E. Herriott, concurred: J. Schult Printed copies are uncontrolled Copyright 2006, Ford Gl
2、obal Technologies, LLC Page 1 of 3 ACID CATALYST, POLYESTER SYSTEM, BAKING, WSK-M99J366-A EXTERIOR TOP COAT 1. SCOPE The material defined by this specification is a solution of acid catalyst in organic solvents. It is to be used in a polyester top coat system required to provide the best exterior qu
3、ality finish. It shall be suitable for spray application. 2. APPLICATION This specification was released originally for a material to be used as an acid catalyst to make polyester top coats suitable to use with relatively low baking temperatures. The catalyst shall only be used for top coats from th
4、e same source as required by the vendor. The amount of addition may vary depending on the quality of the top coats specified. It is permitted to use acid catalysts from a source different to that of the top coat if approved by Materials Laboratory of Product Engineering and agreed by the respective
5、vendors. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3
6、.3 ULTRA VIOLET SPECTROGRAPHIC ANALYSIS All approved materials shall contain with Initial Sample Report an UV-spectroscopic analysis. The equipment used for this measurement is a Lambda 6 Integrating Sphere spectrophotometer or equivalent. This shall be recorded and filed by Quality Control or relev
7、ant Testing Laboratories of the Ford Motor Company. Subsequent material UV-spectroscopic analysis shall correspond to the data of the Initial Sample. 3.4 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 5
8、0 +/- 5% relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. All panels shall be aged for 72 h at 23 +/- 2 C or 16 h at 43 +/- 2 C before testing for resistance properties unless otherwise specified. In the event of differences b
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSKM99J366A2006ACIDCATALYSTPOLYESTERSYSTEMBAKINGEXTERIORTOPCOATTOBEUSEDWITHFORDWSSM99P1111A 汽车 外部

链接地址:http://www.mydoc123.com/p-751075.html