FORD WSG-M1C247-A-2004 GREASE SYNTHETIC HYDROCARBON OIL INORGANICALLY GELLED HIGH VISCOSITY NLGI 0 5 TO BE USED WITH FORD WSS-M99P1111-A 《NLGI 0 5高粘度无机凝胶状合成烃油润滑脂 与标准FORD WSS-M99.pdf
《FORD WSG-M1C247-A-2004 GREASE SYNTHETIC HYDROCARBON OIL INORGANICALLY GELLED HIGH VISCOSITY NLGI 0 5 TO BE USED WITH FORD WSS-M99P1111-A 《NLGI 0 5高粘度无机凝胶状合成烃油润滑脂 与标准FORD WSS-M99.pdf》由会员分享,可在线阅读,更多相关《FORD WSG-M1C247-A-2004 GREASE SYNTHETIC HYDROCARBON OIL INORGANICALLY GELLED HIGH VISCOSITY NLGI 0 5 TO BE USED WITH FORD WSS-M99P1111-A 《NLGI 0 5高粘度无机凝胶状合成烃油润滑脂 与标准FORD WSS-M99.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2004 04 30 Revised Para 3.0 inserted; para 3.1, 3.2, 3.3, 3.6 & 4 deleted 1994 06 30 NGA1E10370437006 Released A.Vallabhanath Printed copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 1 of 5 GREASE, SYNTHETIC HYDROCARB
2、ON OIL, WSG-M1C247-A INORGANICALLY GELLED, HIGH VISCOSITY, NLGI 0.5 1. SCOPE The material defined by this specification is a NLGI 0.5 grease based on synthetic hydrocarbon fluids and inorganic gelling agents. This grease has thixotropic properties. The lubricant operating temperature range is -40 to
3、 150 C. 2. APPLICATION The material defined by this specification was released originally to lubricate electrical switches used in windshield wiper assemblies. It is also for use on windshield wiper assembly gear trains. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material sup
4、pliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.1.1 Initial Qualifications The supplier must furnish to the affected Materials Engineering activity a completed and certified copy of the attached Supplement A and test reports d
5、emonstrating the capability of the process for the listed critical properties. 3.1.2 Ongoing verification Plan In addition to the control plan, the supplier and affected Materials Engineering activity shall establish a mutually agreed upon ongoing product verification plan which will be listed on Su
6、pplement B. 3.4 CONSISTENCY Material shall be a smooth homogenous product free from abrasive particles, it shall be consistent in color and texture, and free from objectionable odors during normal storage. It shall be suitable for the intended application. 3.5 FUNCTIONAL APPROVAL Materials being eva
7、luated for approval to this specification shall be subjected to a production trial. Functional trial results must be approved by the affected assembly operation and Design Engineering. Results shall be made available to Materials Engineering prior to material approval and release. ENGINEERING MATERI
8、AL SPECIFICATIONWSG-M1C247-APrinted copies are uncontrolled Copyright 2004, Ford Global Technologies, LLC Page 2 of 5 5. GENERAL INFORMATION The information below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 TYPICAL PROPERTIES The information sh
9、own is to provide data on products which have been qualified to this specification. The values shown do not constitute part of the requirements for initial qualification. 5.1.1 Color Translucent white 5.1.2 Appearance Smooth 5.1.3 Oil Separation 4.8 wt % (ASTM D 1742, 24 h) 5.1.4 Penetration (ASTM D
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSGM1C247A2004GREASESYNTHETICHYDROCARBONOILINORGANICALLYGELLEDHIGHVISCOSITYNLGI05TOBEUSEDWITHFORDWSSM99P1111ANLGI05

链接地址:http://www.mydoc123.com/p-750247.html