FORD WSD-M1C227-A-2010 GREASE LONG LIFE NLGI 2 TO BE USED WITH FORD WSS-M99P1111-A 《使用寿命长的润滑脂 美国润滑脂协会2 与福特WSS-M99P1111-A 一起使用》.pdf

《FORD WSD-M1C227-A-2010 GREASE LONG LIFE NLGI 2 TO BE USED WITH FORD WSS-M99P1111-A 《使用寿命长的润滑脂 美国润滑脂协会2 与福特WSS-M99P1111-A 一起使用》.pdf》由会员分享，可在线阅读，更多相关《FORD WSD-M1C227-A-2010 GREASE LONG LIFE NLGI 2 TO BE USED WITH FORD WSS-M99P1111-A 《使用寿命长的润滑脂 美国润滑脂协会2 与福特WSS-M99P1111-A 一起使用》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 12 02 Revised See Summary of Revisions C. Mracna, NA 2005 02 14 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.6 & 4 1990 02 04 Released C10057353 P. A. Osman Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC P

2、age 1 of 2 GREASE, LONG LIFE, NLGI 2 WSD-M1C227-A 1. SCOPE The material defined by this specification is a grease consisting of a mineral oil and thickener, with polyethylene and molybdenum disulphide and other additives to give the desired characteristics. 2. APPLICATION This specification was rele

3、ased originally for grease used as a long life chassis lubricant for steering linkage joints and wheel bearings. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M

4、99P1111-A). 3.2 WORKED PENETRATION, tenths of a millimeter 265-295 (ASTM D 217, DIN ISO 2137, 60 strokes) 3.3 DROPPING POINT 178 C min (ASTM D 566) 3.4 SOLIDS CONTENT 2.8 - 3.2% (Fed Std. 791, Method 3720) 3.5 FLOW 800-1200 mm (DIN 5L805, 20C) 4. GENERAL INFORMATION The information given below is pr

5、ovided for clarification and assistance in meeting the requirements of this specification. Grease approved to these specifications should have the following typical properties. 4.1 LITHIUM SOAP (12 hydroxystearate) 6.4% (FLTM AJ 106-02) 4.2 POLYETHYLENE 4.6% (FLTM AJ 106-02, Density 0.956 at 20 C) 4

6、.3 MOLYBDENUM DISULPHIDE 1.1% (FLTM AJ 106-02, 2 - 5 micron size) 4.4 VISCOSITY 15.3 mm2/s (ASTM D 445, DIN 51562, ISO 3164, at 100 C) 4.5 FLASH POINT 232 C min (ASTM D 93) ENGINEERING MATERIAL SPECIFICATIONWSD-M1C227-APrinted copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Pag

7、e 2 of 2 4.6 POUR POINT -15 C (ASTM D 97, DIN ISO 3016) 4.7 PROLONGED WORKED PENETRATION (ASTM D 217, DIN ISO 2137, change after 100,000 strokes) 10% 4.8 OXIDATION STABILITY 152 Kpa (ASTM D 942 or DIN 51808) Pressure drop after 1000 h 4.9 OIL SEPARATION 1.1% (ASTM D 1742, DIN 51817, FTMS 791 C 321.3

8、, 7 days at 40 C) 4.10 FILM STRENGTH DURABILITY No score (ASTM D 2509, 4.54 kgf load, 8 h, min) 4.11 CORROSION PREVENTION Pass (ASTM D 1743) 4.12 INTERFACE COMPATIBILITY Production representative materials specific to the application should be used for the following tests. 4.12.1 Chemical Attack to

9、Painted Surfaces (FLTM BJ 126-01) Note: Not tested for initial application of this grease. Grease must be tested for chemical attack to painted surfaces for applications that come in contact with paint surfaces, ex. E-coat and powder coat. 4.12.2 Resistance to Stress Cracking (FLTM BO 127-03) Note:

10、Not tested for initial application of this grease. Grease must be tested for resistance to stress cracking when used for additional applications that come in contact with polymers such as PC, ABS, PC+ABS, ASA or acrylic. 4.12.3 Elastomer Compatibility (ASTM D 4289, 70 h, 100 C, DIN 53505, DIN 53504)

11、 Volume change Hardness change, max Tensile Strength change Note: Not tested for initial application of this grease. Grease must be tested for elastomer compatibility when used for additional applications that come in contact with elastomers. Application specific elastomer should be used for testing instead of a reference elastomer. 5. SUMMARY OF REVISIONS 2010 12 02 Lot certification tests moved to requirements. Added information on interface compatibility which are requirements in WSS-M13P13-A.