FORD M2C183-A-2009 LUBRICANT MULTIPURPOSE POLYMER《多用聚合物润滑油》.pdf

《FORD M2C183-A-2009 LUBRICANT MULTIPURPOSE POLYMER《多用聚合物润滑油》.pdf》由会员分享，可在线阅读，更多相关《FORD M2C183-A-2009 LUBRICANT MULTIPURPOSE POLYMER《多用聚合物润滑油》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 15 N-STATUS No Replacement Named L. Sinclair, FNA 1985 11 01 Page 1 of 2 LUBRICANT, MULTIPURPOSE, POLYMER M2C183-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material defined by this standard is a

2、multiviscosity, extreme pressure lubricant consisting of refined mineral oil with suitable additives. 2. APPLICATION: This material shall be suitable for use as a transmission gear lubricant and/or where specified. 3. REQUIREMENTS: 3.1 VISCOSITY: (ASTM D 455 & D 2161) AGMA Grade 6EP (SAE 85W 140) cS

3、t at 38.0 C 384-394 cSt at 98.9 C 27.5-30.1 SUS at 38.0 C 1780-1825 SUS at 98.9 C 130-143 3.2 VISCOSITY INDEX: (ASTM D 2270) 110 min 3.3 FLASH POINT: C (ASTM D 92) 216 min 3.4 FIRE POINT: C (ASTM D 92) 224 min 3.5 POUR POINT: C (ASTM D 97) -25 max 3.6 SULFUR: % wt (ASTM D 129) 1.5 min 3.7 POLYMERS:

4、% wt 15 min (TGA Method) 3.8 EXTREME PRESSURE TEST: Timken Lever Load 45 lbs (20 Kg) min (FLTM BJ1-2) 3.9 COPPER STRIP TEST: (ASTM D 130) 1a max NON-PRODUCTION MATERIAL SPECIFICATION M2C183-A Page 2 of 2 3.10 INHIBITORS: These lubricants shall contain suitable additives to inhibit oxidation, rust an

5、d foaming. 3.11 TOXICITY: This material shall not contain any skin sensitizers, primary irritants or other ingredients considered harmful to employee health under normal use conditions. 3.12 COMPOSITION: The material supplied must be of uniform texture and consistency and must not become rancid or s

6、how component separation. 3.13 COMPATIBILITY: All material to this Standard shall be compatible in all proportions with other materials currently approved under these “M“ numbers. Separation, precipitation or flocculation of solids or gels shall not be permitted. 3.14 SUPPLIER RESPONSIBILITY: All ma

7、terials supplied to this standard must be equivalent in all characteristics to the material upon which approval was originally granted and shall be suitable for the intended application. Changes in composition shall not be made without approval of the responsible Staff Office in accordance with Manu

8、facturing Procedure IId1. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this Standard must have Regulatory Clearance, Laboratory and Shop Trial approvals. Suppliers are required to complete and submit the Material Health, Safety and Environmental Data Sheet (Form 1291A) p

9、rior to shop trial. Recommendations for the addition of new manufacturers to the Manufacturing Approved Source List (ASL) must be made in writing to the responsible Staff Office by the appropriate divisional standards activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONTROL

10、: Use of any material approved to this standard must comply with the guidelines as established in the environmental review of the material, as they appear in the Materials and Toxicology (MATS) System. 6. HEALTH AND SAFETY: Use of any material approved to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS System.