FORD FLTM BV 001-05-2000 BOND ADHESION OF ACOUSTICAL DEADENERS《隔音材料的粘附性》.pdf

《FORD FLTM BV 001-05-2000 BOND ADHESION OF ACOUSTICAL DEADENERS《隔音材料的粘附性》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BV 001-05-2000 BOND ADHESION OF ACOUSTICAL DEADENERS《隔音材料的粘附性》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BV 001-05 Date Action Revisions 2000 08 10 Editorial no technical change A. Cockman 1992 08 11 Printed copies are uncontrolled Page 1 of 5 Copyright 2000, Ford Global Technologies, Inc. BOND ADHESION OF ACOUSTICAL DEADENERS Application This test method is used to determi

2、ne the adhesive bond strength of pressure sensitive and heat bondable mastics. Apparatus Required Universal Tester Instron Model TM or equivalent with strip chart re corder. Special Fixture to Replace Upper Jaw Grip See Figures 1 and 2. Steel Panel CRLC 0.90 x 100 x 250 mm, primed with currently rel

3、eased primer system per ESB - M2P22 - A (prime only). Razor Blade or Knife Conditioning and Test Conditions All test val ues indicated herein are based on material conditioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h prior to testing and test

4、ed under the same conditions unless otherwise specified. Procedure 1. Bond a 125 x 25 mm test strip of mastic along the length of the steel panel. Heat bondable or other mastics will be bonded per the applicable engineering material specification. Pressure sensitive mastics will be bonded by rolling

5、 a 4.5 kg weight twice over the length of the test strip. 2. Condition bonded test strips for 24 h at 23 +/ - 2 C and 50 +/ - 5 % relative humidity prior to testing. Using a razor blade or knife, cut the test strip into 25 x 25 mm sections. FORD LABORATORY TEST METHOD BV 001-05 Page 2 of 5 Copyright

6、 2000, Ford Global Technologies, Inc. 3. Position the steel panel in the lower jaw of the test machine such that the test strip is perpendicular to, and inside the arms of, the special fixture (refer to Figure 1 and 3). The fixture roller arm must be on the back side of the steel panel. Center the 2

7、5 x 25 mm section of the te st strip to be evaluated directly above the peel edge of the special fixture arm (Figure 3). 4. Tighten the lower jaws to insure that the steel panel does not slip during the test. 5. Tighten the special fixture arms with the adjustment screw so that the arms are in conta

8、ct with the steel panel but the panel is able to move freely as the panel is pulled through the fixture arms. 6. Set the cross head and recording chart to run at 300 mm/minute. Apply load to the test specimen until load indicator return s to zero (i.e., until individual section of mastic is removed)

9、. 7. Record the maximum load obtained for five sections of the test strip. The average of these shall be reported as the bond adhesive strength. Chemicals, materials, parts, and equipment r eferenced in this document must be used and handled properly. Each party is responsible for determining proper

10、 use and handling in its facilities. FORD LABORATORY TEST METHOD BV 001-05 Page 3 of 5 Copyright 2000, Ford Global Technologies, Inc. BOND ADHESION OF ACOUSTICAL DEADENERS Dimensions are in inches. Figure 1 FORD LABORATORY TEST METHOD BV 001-05 Page 4 of 5 Copyright 2000, Ford Global Technologies, Inc. BOND ADHESION OF ACOUSTICAL DEADENERS FORD LABORATORY TEST METHOD BV 001-05 Page 5 of 5 Copyright 2000, Ford Global Technologies, Inc. BOND ADHESION OF ACOUSTICAL DEADENERS Figure 3