FORD SK-M99G9517-A-2006 DEADENER SHEETING LOW TEMPERATURE FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《低温可熔的隔音材料毡 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD SK-M99G9517-A-2006 DEADENER SHEETING LOW TEMPERATURE FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《低温可熔的隔音材料毡 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD SK-M99G9517-A-2006 DEADENER SHEETING LOW TEMPERATURE FUSIBLE TO BE USED WITH FORD WSS-M99P1111-A 《低温可熔的隔音材料毡 与标准FORD WSS-M99P1111-A一起使用 》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions 2006 10 25 Revised Inserted 3.0; Deleted 3.18 & 4 1994 12 16 Revised and Retyped Was 11 pages 1976 12 17 Released SM/EQ8198MP Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 5 DEADENER SHEETING, LOW TEM
2、PERATURE FUSIBLE SK-M99G9517-A DEADENER SHEETING, LOW TEMPERATURE FUSIBLE SK-M99G9517-B 1. SCOPE The material defined by these specifications is a bitumen synthetic resin and/or synthetic rubber based self adhesive heat fusible sheeting with an anti-blocking surface finish on one side. The adhesive
3、side of sheeting is to be protected by a release paper. 2. APPLICATION This material was originally released for bonding under heat to vertically EC primed respectively spray primed door inner panels in the paint oven. 3. REQUIREMENTS Material specification requirements are to be used for initial qu
4、alification of materials. The material shall be conditioned for a minimum of 24 hours at 23 +/- 2 C and 50 +/- 5% relative humidity prior to test. 3.1 COLOR Black or as specified on Engineering drawing. 3.2 SOLIDS, min 99% (FLTM BV 150-10) 3.3 ASH, max 60% (FLTM BV 150-10) 3.4 THICKNESS (Slide gauge
5、) As specified on Engineering drawing in accordance with Figure 1. 3.5 WEIGHT/m2, max 2.2 kg (Based on 1 mm thickness) 3.6 HEAT STABILITY The material shall fuse properly to the substrate without evidence of flow-off, blistering, cracking or shrinkage. Test Method: 1) Apply 280 x 300 mm pieces of te
6、st material to 300 x 300 x 1.5 mm test panels prepared according FLTM BI 120-01 with the tacky side facing to the panel and press together the whole area evenly using a roller according to ASTM D 1000. ENGINEERING MATERIAL SPECIFICATION SK-M99G9517-A SK-M99G9517-B Printed copies are uncontrolled Cop
7、yright 2006, Ford Global Technologies, LLC Page 2 of 5 2) Expose test specimens to heat according to FLTM BV 150-05, Table 3 (use separate specimens for each curing cycle) a) Minimum Curing Cycle b) Maximum Curing Cycle in vertical position. 3) Examine after cooling to room temperature. 3.7 COLD ADH
8、ESION No chipping, no loss of adhesion (FLTM BV 151-02, Method B, Load A, -30 +/- 2 C specimen preparation according to 3.6 of Test Method, section 1 and 2, test panel thickness 1.5 +/- 0.1 mm) 3.8 ADHESION AFTER HEAT AGEING No chipping, no loss of adhesion (FLTM BV 155-02, Method B, Load A, specime
9、n preparation according to 3.6 of Test Method, section 1 and 2, heat ageing 14 d at 80 +/- 2 C, test panel thickness 1.5 +/- 0.1 mm) 3.9 SALT FOG RESISTANCE No corrosion Test Method: 1) Specimen preparation according to 3.6 except specimen size of 280 x 280 mm, distance from panel edges 20 mm. 2) Co
10、ndition test specimens for 24 hours at room temperature and subject to a salt fog according to ASTM B 117 for 240 hours. 3) Remove a 30 x 280 mm strip of material from test specimens and examine for evidence of corrosion. 3.10 TEMPERATURE CYCLING TEST No chipping, no shrinkage, no blistering or loss
11、 of adhesion. Test Method: 1) Specimen preparation according to 3.9, Test Method, section 1. ENGINEERING MATERIAL SPECIFICATION SK-M99G9517-A SK-M99G9517-B Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 5 2) Condition test specimens for 24 hours at room tempe
12、rature and subject three times to the following cycle: 3 h at 80 +/- 2 C 1 h at 23 +/- 2 C 3 h at -30 +/- 2 C 1 h at 23 +/- 2 C 16 h at 38 +/- 2 C and 98 +/- 2% relative humidity 3) After conditioning at room temperature for 24 hours, test specimens according to FLTM BV 055-02, Method A, test panel
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDSKM99G9517A2006DEADENERSHEETINGLOWTEMPERATUREFUSIBLETOBEUSEDWITHFORDWSSM99P1111A 低温 隔音材料 标准 FORDWSSM99P1111A

链接地址:http://www.mydoc123.com/p-748173.html