FORD ESB-M36J1-A3-2012 ENAMEL CATALKYZED 2- COMPONENT CLEARCOAT HIGH SOLIDS WET-ON-WET LOW BAKE REPAIR PROCESS - EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD ESB-M36J1-A3-2012 ENAMEL CATALKYZED 2- COMPONENT CLEARCOAT HIGH SOLIDS WET-ON-WET LOW BAKE REPAIR PROCESS - EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M36J1-A3-2012 ENAMEL CATALKYZED 2- COMPONENT CLEARCOAT HIGH SOLIDS WET-ON-WET LOW BAKE REPAIR PROCESS - EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Release/Revision890602 NB00I10023641 ReleasedWP 3948-a Page 1 of 2 ENAMEL, CATALYZED 2-COMPONENT CLEARCOAT, HIGH ESB-M36J1-A3SOLIDS, WET-ON-WET LOW BAKE REPAIR PROCESS- EXTERIOR1. SCOPEThe material defined by this

2、sp ecification is a catalyzed exterior qualitytwo-component urethane clearcoat utilized for low bake repair, and whichyields a durable glossy appeara nce when sprayed over ESB-M36J1-A1 basecoatwet-on-wet and monobaked.2. APPLICATIONThis specification was released originally for material used as the

3、topcoatfinish on automobile bodies, hoods, fenders and other exterior parts, andshall be satisfactory for use over specified primers, or electrocoats, orover previously baked enamel, as in paint repair or two-tone operations.3. REQUIREMENTS3.1 STATISTICAL PROCESSSupplie rs must conform to the requir

4、ements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for material/source approval. Appropriatestatist ical tools must be used to analyze process/product data sothat variation in the final product is continuously reduced.3.2 COMPATIBILITYThe

5、re shall be compatibility between all topcoats, primers, sealersand a dhesives utilized in the assembly plant. This will allow fornormal production processing of these materials. Refer to the SealerApplication Manual for the description of specif ic sealers/adhesives.3.3 COMPOSITIONVehicle: The vehi

6、cle s ystem consists of two thermosetting, urethaneresins which combine to yield a clear film of high gloss, excellentdistinctness of image, and superior weatherability.Ultrav iolet Light Absorber and Stabilizer: The clearcoat shallcont ain UV-absorber and/or hindered amine in sufficient amount topr

7、ovide good long-term durability.ENGINEERING MATERIAL SPECIFICATIONESB-M36J1-A3WP 3948-b Page 2 of 2 3.4 PERFORMANCEThis material shall meet all requirements of ESB -M36J1-A2 high solids2-component urethane clearcoat.3.4.1 Bake ScheduleThis system shall cure at the catalyzed repair bake scheduleof 20

8、 min at 99 C ambient (which must provide a minimum of 10min at 99 C metal temperature).3.5 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon which approval wasoriginally granted.Pri or to making any change in the prope

9、rties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the Supplier shall notify Purchasing, Toxicology andthe affected Materials En

10、gineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions imposed by law, regulations or Ford, apply tothe materials addressed by th

11、is document. The restrictions aredefined in Engineering Material Specification WS S-M99P9999-A1, unlessa different suffix (e.g., A2 or A3) is specified on the engineeringdocument for the application.4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by therespo

12、nsible Materials Engineeri ng activity. Suppliers desiring approval ofthe ir materials shall first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity its own laboratory rep ort to the specification (test results, notnominal values), the material designation and code number, and testspecim ens for Ford evaluation. Upon approval, the material will be addedto the Engineering Material Approved Source List.