FORD ESB-M2F67-B-2003 FABRIC VINYL COATED TO BE USED WITH FORD WSS-M99P1111-A 《乙烯树脂涂层织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf
《FORD ESB-M2F67-B-2003 FABRIC VINYL COATED TO BE USED WITH FORD WSS-M99P1111-A 《乙烯树脂涂层织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享,可在线阅读,更多相关《FORD ESB-M2F67-B-2003 FABRIC VINYL COATED TO BE USED WITH FORD WSS-M99P1111-A 《乙烯树脂涂层织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2003 08 26 Revised Para 3.0 inserted; Para 3.1, 3.30, 4 deleted 1979 10 12 Activated Metricated and Retyped CAHI-RD572066-255 1971 08 20 Released 4B1-302-16 Printed copies are uncontrolled Copyright 2003, Ford Global Technologies, Inc. Page 1
2、of 5 FABRIC, VINYL COATED ESB-M2F67-B 1. SCOPE The material defined by this specification is vinyl copolymer or vinyl chloride, coated knit fabric of good quality and uniform composition. 2. APPLICATION This specification was released originally for material used in applications specified on Enginee
3、ring Chart 534. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 APPEARANCE (FLTM BI 109-01) The color, pattern, and finish shall match the approved Design Center
4、 master sample, or shall be as specified on the engineering drawing. 3.3 BACKING ESB-M9H1-A 3.4 WEIGHT, min (FLTM BN 106-01) Coating 9.5 oz/yd2 (0.322 kg/m2) Total 14.0 oz/yd2(0.475 kg/m2) 3.5 WIDTH Specified on Chart 534 3.6 TENSILE STRENGTH, 10% Tolerance (ASTM D 1682, Grab Method) Warp 100 lb (44
5、5 N) Fill 65 lb (289 N) 3.7 STRETCH AND SET (SAE J 855) Stretch Set Warp 1-5% 0-2% Fill 7-13% 0-4% ENGINEERING MATERIAL SPECIFICATION ESB-M2F67-BPrinted copies are uncontrolled Copyright 2003, Ford Global Technologies, Inc. Page 2 of 5 3.8 STIFFNESS (ASTM D 747, direct reading at 60 angle with 0.1 i
6、n-lb (0.01 N-m) load) Non-metallic Metallic Warp 15 18 Fill 13 13 The test specimen shall be 2 in (50 mm) x 1 in (25 mm) with 1 in (25 mm) of the 2 in (50 mm) dimension clamped in jaw, 1/2 in (13 mm) span from clamp to bending plate, fabric side up. 3.9 TEAR STRENGTH (trapezoid), min (ASTM D 5733) W
7、arp and Fill 3.5 lb (15.6 N) 3.10 SHRINKAGE, max (FLTM BN 105-01) Warp 3.0% Fill 1.5% 3.11 ADHESION OF COATING 4 lb/in (701 N/m) width TO BACKING FABRIC, min (ASTM D 413, Machine Method; the coating of the test specimen shall be separated from the backing fabric, by hand and without the use of solve
8、nts, prior to pulling. The movable jaw of the testing machine shall move at the rate of 12 in (305 mm)/min.) 3.12 SEAM STRENGTH, min (FLTM BN 119-01) Warp 85 lb (378 N) Fill 50 lb (222 N) Note: The above values apply to fabric breaks only. Thread breaks which exceed the above requirements shall be a
9、ccepted. However, results below the above requirements which are due to thread breaks shall be disregarded and the tests repeated. 3.13 COLD FLEXIBILITY No failure (FLTM BN 102-01, -34 C) 3.14 CROCKING Rating 5 (FLTM BN 107-01) 3.15 MIGRATION STAINING (FLTM BN 103-01) The coated surfaces shall show
10、no evidence of injurious exudation, adhesion (tackiness), separation, color transfer, or flattening of embossing, when placed face to face with itself, or materials of the 2F4-9-62-67 etc., series. ENGINEERING MATERIAL SPECIFICATION ESB-M2F67-BPrinted copies are uncontrolled Copyright 2003, Ford Glo
11、bal Technologies, Inc. Page 3 of 5 3.16 H2S STAINING Rating 5 (FLTM AN 102-01) Production materials shall exhibit H2S staining qualities equal to or better than the master sample (as approved for production and filed by the Textile Engineering Section, BEPE Materials Engineering Department.) 3.17 FA
12、DE (SAE J 1885, 120 SFH) The vinyl coating shall not stain, exhibit color tone change or change in hue, in accordance with rating 5 of the AATCC Gray Scale for Measuring Change in Color. Production materials shall exhibit light fastness qualities equal to or better than the master sample (as approve
13、d for production and filed by the Textile Engineering Section, BEPE Materials Engineering Department. 3.18 AGING When the specimens used for the resistance to fade test (Para 3.17) are folded 180 upon themselves (coating side out), the coating shall not crack. 3.19 ABRASION (FLTM BN 108-02) After th
14、e wear test, the materials color and pattern in the wear area shall be compatible in appearance with the adjacent unabraded areas of the wear test specimen. Printed, metallic, and other vinyl surface coatings shall withstand 500 cycles, using CS #10 wheels, and 1000 g load. The color of the base vin
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDESBM2F67B2003FABRICVINYLCOATEDTOBEUSEDWITHFORDWSSM99P1111A 乙烯 树脂 涂层 织物 标准 FORDWSSM99P1111A 一起 使用

链接地址:http://www.mydoc123.com/p-745298.html