ETSI TS 102 936-2-2011 eCall Network Access Device (NAD) conformance specification Part 2 Test Suites (V1 1 1 Includes Diskette)《eCall网络接入设备(NAD)一致性规范 第2部分 测试套件(版本1 1 1) 包括磁盘》.pdf

《ETSI TS 102 936-2-2011 eCall Network Access Device (NAD) conformance specification Part 2 Test Suites (V1 1 1 Includes Diskette)《eCall网络接入设备(NAD)一致性规范 第2部分 测试套件(版本1 1 1) 包括磁盘》.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 936-2-2011 eCall Network Access Device (NAD) conformance specification Part 2 Test Suites (V1 1 1 Includes Diskette)《eCall网络接入设备(NAD)一致性规范 第2部分 测试套件(版本1 1 1) 包括磁盘》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 936-2 V1.1.1 (2011-04)Technical Specification eCall Network Access Device (NAD)conformance specification;Part 2: Test Suitesfloppy3ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)2Reference DTS/MSG-00eCall01-2 Keywords cellular, conformance, ecall, emergency, GSM, mobile, testing, UMTS ETSI 650

2、Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloa

3、ded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference s

4、hall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is ava

5、ilable at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The

6、 copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2011. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM

7、is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. LTE is a Trade Mark of ETSI currently being registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the G

8、SM Association. ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)3Contents Intellectual Property Rights 4g3Foreword . 4g3Introduction 4g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Requi

9、rements on the TTCN development 8g35 ATS structure - Modularity 8g36 Test method and testing architecture 9g37 PCO and ASP definitions . 9g38 Design Considerations 9g3Annex A (normative): Abstract Test Suite (ATS) . 10g3A.1 Version of specifications 10g3A.2 eCall ATS . 10g3A.2.1 The TTCN Machine Pro

10、cessable form (TTCN.MP) 10g3Annex B (normative): Partial IXIT proforma . 11g3B.1 eCall test suite parameters declarations 11g3Annex C (informative): Additional information to IXIT 12g3Annex D (informative): PCTR Proforma . 13g3Annex E (informative): Bibliography . 14g3History 15g3ETSI ETSI TS 102 93

11、6-2 V1.1.1 (2011-04)4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “

12、Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no i

13、nvestigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Sp

14、ecification (TS) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document is part 2 of a multi-part deliverable covering eCall Network Access Device (NAD) conformance specification as identified below: Part 1: “Protocol test specification“; Part 2: “Test suite

15、s“. The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be fou

16、nd under http:/webapp.etsi.org/key/queryform.asp . Introduction Following a decision of the European Parliament, and a request by the European Commission to ETSI, ETSI TC MSG was tasked with managing the technical specification and creation of open standards for the Pan-European eCall emergency serv

17、ice. An eCall is an emergency voice call, initiated manually or automatically from a vehicle to a Public Safety Answering Point (PSAP), supplemented by up to 140 bytes of incident related data. The Minimum Set of Data (MSD) has been defined by CEN Technical Committee 278 and includes the GNSS derive

18、d location and direction of travel of the vehicle, the Vehicle Identification Number (VIN) and other information to enable the emergency response teams to quickly location and provide medical and other life saving assistance to the accident victims. eCall has been designed to operate over any PLMN t

19、hat supports emergency voice calls, specifically TeleService 12. Should the MSD not be transmitted or received for any reason, or if the PSAP is not equipped with the necessary eCall equipment (eCall modem / server), the accident victims and PSAP operator may still converse using the In-Vehicle Syst

20、em (IVS) audio equipment. The 3rdGeneration Partnership Project (3GPP) has specified the eCall service requirements, data transmission protocols and network signaling aspects for Release 8. NOTE: Early implementation of eCall in Release-7 is certifiable. The in-band modem used to transfer the MSD fr

21、om the vehicle to the PSAP, following the establishment of a 112 or other emergency voice call, has been specified by 3GPP TSG SA4. Once an eCall is invoked - initiated manually by the vehicle occupants or automatically as the result of an accident, the eCall call set-up and clear-down procedures (R

22、R, CC, and MM) are automatically controlled by the eCall in-vehicle system (IVS) and network access device (NAD). Once initiated the system requires no MMI intervention and does not permit the user to intervene at any stage during call management. It is important, therefore, that the eCall system wo

23、rks autonomously and reliable when faced with a wide range of probable network access events. ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)5An eCall NAD may be used to access other non-emergency subscription services or for the purpose of making emergency calls only. In the latter case the eCall NAD is re

24、ferred to an eCall only device and there are specific network access restrictions placed on these devices in order to avoid the generation of large volumes of unnecessary MM signaling, when not engaged in an eCall, test or reconfiguration call TS 122 101 1. The eCall NAD is permitted to make calls t

25、o a non-emergency number for the purpose of testing, or requesting the reconfiguration of the NAD to lift the network access restriction so as to allow the NAD to register on power-up and to access subscribed to commercial services. The eCall in-band modem conformance test protocols are as specified

26、 in TS 126 269 2. A vademecum on the applicability of ETSI GSM and UMTS mobile station harmonised standards EN 301 908 parts 1 7 and 2 8 and EN 301 511 9 to the ETSI specified eCall NAD, for the purpose of demonstrating compliance with R - the test methods and PCO definitions; - the test configurati

27、ons; - the design principles, assumptions, and used interfaces to the TTCN tester (System Simulator); - TTCN styles and conventions; - the partial PIXIT proforma; - the TTCN.MP form for the mentioned protocols tests. The Abstract Test Suites designed in the present document are based on the test cas

28、es specified in prose (TS 102 936-1 10). 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced

29、 document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee t

30、heir long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI TS 122 101: “Universal Mobile Telecommunications System (UMTS); LTE; Service aspects; Service principles (3GPP TS 22.101)“. 2 ETSI TS 126 269: “Digit

31、al cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); eCall data transfer; In-band modem solution; Conformance testing (3GPP TS 26.269)“. 3 ETSI TS 134 109: “Universal Mobile Telecommunications System (UMTS); LTE; Terminal logical test interface; Specia

32、l conformance testing functions (3GPP TS 34.109)“. 4 ETSI TS 134 123-1: “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) conformance specification; Part 1: Protocol conformance specification (3GPP TS 34.123-1)“. 5 ETSI TS 134 123-3: “Universal Mobile Telecommunications System

33、(UMTS); User Equipment (UE) conformance specification; Part 3: Abstract Test Suites (ATSs) (3GPP TS 34.123-3)“. 6 ETSI TS 134 108: “Universal Mobile Telecommunications System (UMTS); LTE; Common test environments for User Equipment (UE); Conformance testing (3GPP TS 34.108)“. 7 ETSI EN 301 908-1: “I

34、MT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 1: Introduction and common requirements“. ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)78 ETSI EN 301 908-2: “Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular ne

35、tworks; Part 2: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering the essential requirements of article 3.2 of the R Harmonized EN for mobile stations in the GSM 900 and GSM 1800 bands covering essential requirements under article 3.2 of the R Part 1: Protocol te

36、st specification“. 11 ETSI TS 124 008: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Mobile radio interface Layer 3 specification; Core network protocols; Stage 3 (3GPP TS 24.008)“. 2.2 Informative references The following referenced

37、documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual

38、 recognition of their conformity (R Universal Mobile Telecommunications System (UMTS); LTE; Vocabulary for 3GPP Specifications (3GPP TR 21.905)“. i.3 ETSI TR 101 666: “Information technology Open Systems Interconnection Conformance testing methodology and framework; The Tree and Tabular Combined Not

39、ation (TTCN) (Ed. 2+)“. i.4 ETSI TR 102 937: “Mobile systems; Guidelines on applicability of GSM and UMTS mobile station harmonized standards to eCall Network Access Device (NAD)“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions giv

40、en in TR 121 905 i.2 and the following apply: eCall: manually or automatically initiated emergency call, (TS12) from a vehicle, supplemented with a minimum set of emergency related data (MSD), as defined under the EU Commissions eSafety initiative Minimum Set of Data (MSD): data component of an eCal

41、l sent from a vehicle to a Public Safety Answering Point or other designated emergency call centre NOTE: The MSD has a maximum size of 140 bytes and includes, for example, vehicle identity, location information and time-stamp. 3.2 Abbreviations For the purposes of the present document, the abbreviat

42、ions given in TR 121 905 i.2 and the following apply: ATS Abstract Test Suite IVS In Vehicle System (eCall terminal and associated sub-systems in vehicle) NAD Network Access Device ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)84 Requirements on the TTCN development A number of requirements are identified

43、for the development and production of TTCN specification for 3GPP UE at Uu interface. 1. Top-down design, following TS 134 123-1 4, TS 134 108 6 and TS 134 109 3. 2. A unique testing architecture and test method for testing all protocol layers of UE. 3. Uniform TTCN style and naming conventions. 4.

44、Improve TTCN readability. 5. Using TTCN-2+ (TR 101 666 i.3) avoid the use of the TTCN 2 features TTCN 3 does not support. 6. TTCN specification feasible, implementable and compilable. 7. Test cases shall be designed in a way for easily adaptable, upwards compatible with the evolution of the 3GPP cor

45、e specifications and the future Releases. 8. The test declarations, data structures and data values shall be largely reusable. 9. Modularity and modular working method. 10. NAS ATS should be designed being independent from the radio access technologies. 11. Minimizing the requirements of intelligenc

46、e on the emulators of the lower testers. Especially the functionality of the RRC emulator in the TTCN tester should be reduced and simplified, the behaviours should be standardized as the TTCN RRC test steps in the TTCN modular library. 12. Giving enough design freedom to the test equipment manufact

47、urers. 13. Maximizing reuse of ASN.1 definitions from the relevant core specifications. In order to fulfil these requirements and to ensure the investment of the test equipment manufacturers having a stable testing architecture for a relatively long period, a unique testing architecture and test met

48、hod are applied to the 3GPP UE protocol tests. 5 ATS structure - Modularity The eCall ATS is developed making use of the modular TTCN approach used for the development of the 3GPP ATS specifications. The following modules are used: BasicM, RRC_M, L3M, NAS_M, HSR5_R6_M, R7_M and R8_M. The module stru

49、cture is shown in figure 1. ETSI ETSI TS 102 936-2 V1.1.1 (2011-04)9BasicM L3M RRC_M NAS_MeCall TS 124 008 11 eCall HSR5_R6_M/ R7_M/ R8_M Figure 1: Module structure The content of the modules is detailed in TS 134 123-3 5, clause 5.1.2. 6 Test method and testing architecture The test method and testing architecture is described in TS 134 123-3 5, clauses 6.1 and 6.2. For the eCall ATS, the NAS test method and architecture is used as described in TS 134 123-3 5, clause 6.3. 7 PCO and ASP definitions The test PCO and