ETSI TS 102 916-1-2012 Intelligent Transport Systems (ITS) Test specifications for the methods to ensure coexistence of Cooperative ITS G5 with RTTT DSRC Part 1 Protocol Implementa.pdf

《ETSI TS 102 916-1-2012 Intelligent Transport Systems (ITS) Test specifications for the methods to ensure coexistence of Cooperative ITS G5 with RTTT DSRC Part 1 Protocol Implementa.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 916-1-2012 Intelligent Transport Systems (ITS) Test specifications for the methods to ensure coexistence of Cooperative ITS G5 with RTTT DSRC Part 1 Protocol Implementa.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 916-1 V1.1.1 (2012-05) Intelligent Transport Systems (ITS); Test specifications for the methods to ensure coexistence of Cooperative ITS G5 with RTTT DSRC; Part 1: Protocol Implementation Conformance Statement (PICS) Technical Specification ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)2Refere

2、nce DTS/ITS-0040022 Keywords DSRC, ITS, PICS, radio, RTTT ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Import

3、ant notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the

4、Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Inform

5、ation on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No par

6、t may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2012. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered

7、for the benefit of its Members. 3GPPTM and LTETMare Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)3Contents Intellectual P

8、roperty Rights 4g3Foreword . 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Conformance 6g3Annex A (normative): PICS proforma . 7g3A.1 Guidance for completing t

9、he ICS proforma . 7g3A.1.1 Purposes and structure 7g3A.1.2 Abbreviations and conventions 7g3A.1.3 Instructions for completing the PICS proforma 8g3A.2 Identification of the Network Equipment . 9g3A.2.1 Date of the statement 9g3A.2.2 Network Equipment Under Test identification. 9g3A.2.3 Product suppl

10、ier 9g3A.2.4 Client 10g3A.2.5 PICS contact person . 10g3A.3 Identification of the protocol 11g3A.4 Global statement of conformance . 11g3A.5 PICS proforma tables . 11g3A.5.1 Roles . 11g3A.5.2 System Capabilities 11g3History 12g3ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)4Intellectual Property Rights IPR

11、s essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or po

12、tentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. N

13、o guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intell

14、igent Transport System (ITS). The present document is part 1 of a multi-part deliverable covering the test specifications for the methods to ensure coexistence of cooperative ITS G5 with RTTT DSRC; Conformance Testing, as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS

15、)“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)“. Introduction To evaluate protocol conformance of a particular implementation, it is necessary to have a statement of which capabilit

16、ies and options have been implemented for a telecommunication specification. Such a statement is called a Protocol Implementation Conformance Statement (PICS). ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)51 Scope The present document provides the Protocol Implementation Conformance Statement (PICS) profo

17、rma for the test specifications for the methods to ensure coexistence of cooperative ITS G5 with RTTT DSRC as specified in TS 102 792 i.1 and ES 202 663 1 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 3 and ETS 300 406 4. The suppli

18、er of a protocol implementation which is claimed to conform to TS 102 792 i.1 and ES 202 663 1 is required to complete a copy of the PICS proforma provided in annex A of the present document and is required to provide the information necessary to identify both the supplier and the implementation. 2

19、References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies

20、. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative refe

21、rences The following referenced documents are necessary for the application of the present document. 1 ETSI ES 202 663: “Intelligent Transport Systems (ITS); European profile standard for the physical and medium access control layer of Intelligent Transport Systems operating in the 5 GHz frequency b

22、and“. 2 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 3 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementatio

23、n Conformance Statements“. 4 ETSI ETS 300 406: “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 2.2 Informative references The following referenced documents are not necessary for the application of the present docum

24、ent but they assist the user with regard to a particular subject area. i.1 ETSI TS 102 792: “Intelligent Transport Systems (ITS); Mitigation techniques to avoid interference between European CEN Dedicated Short Range Communication (RTTT DSRC) equipment and Intelligent Transport Systems (ITS) operati

25、ng in the 5 GHz frequency range“. ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)63 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 102 792 i.1, ES 202 663 1 and the following apply: PICS proforma: document, in the form of a quest

26、ionnaire, designed by the protocol specifier or conformance test suite specifier, which, when completed for an OSI implementation or system, becomes the PICS NOTE: See ISO/IEC 9646-1 2. Protocol Implementation Conformance Statement (PICS): statement made by the supplier of an Open Systems Interconne

27、ction (OSI) implementation or system, stating which capabilities have been implemented for a given OSI protocol NOTE: See ISO/IEC 9646-1 2. static conformance review: review of the extent to which the static conformance requirements are met by the IUT, accomplished by comparing the PICS with the sta

28、tic conformance requirements expressed in the relevant standard(s) NOTE: See ISO/IEC 9646-1 2. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in TS 102 792 i.1, ES 202 663 1 and the following apply: ICS Implementation Conformance Statement OBU On Board Unit PDU P

29、rotocol Data Unit PICS Protocol Implementation Conformance Statement TX Transmission 4 Conformance A PICS proforma which conforms to this PICS proforma specification shall be technically equivalent to annex A, and shall preserve the numbering and ordering of the items in annex A. A PICS which confor

30、ms to this PICS proforma specification shall: a) describe an implementation which claims to conform to TS 102 792 i.1 and ES 202 663 1; b) be a conforming ICS proforma which has been completed in accordance with the instructions for completion given in clause A.1; c) include the information necessar

31、y to uniquely identify both the supplier and the implementation. ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)7Annex A (normative): PICS proforma Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely re

32、produce the PICS proforma in this annex so that it can be used for its intended purposes and may further publish the completed PICS proforma. A.1 Guidance for completing the ICS proforma A.1.1 Purposes and structure The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an

33、 implementation of the requirements defined in relevant specifications may provide information about the implementation in a standardised manner. The PICS proforma is subdivided into clauses for the following categories of information: instructions for completing the PICS proforma; identification of

34、 the implementation; identification of the protocol; PICS proforma tables (for example: major capabilities, etc.). A.1.2 Abbreviations and conventions This annex does not reflect dynamic conformance requirements but static ones. In particular, a condition for support of a PDU parameter does not refl

35、ect requirements about the syntax of the PDU (i.e. the presence of a parameter) but the capability of the implementation to support the parameter. In the sending direction, the support of a parameter means that the implementation is able to send this parameter (but it does not mean that the implemen

36、tation always sends it). In the receiving direction, it means that the implementation supports the whole semantic of the parameter that is described in the main part of this specification. As a consequence, PDU parameter tables in this annex are not the same as the tables describing the syntax of a

37、PDU in the reference specification. The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 3. Item column The item column contains a number which identifies the item in the table. Item description column The

38、 item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly means “is supported by the implementation?“. Reference column The reference column gives reference to the relevant sections in core specifications. ETSI ETSI TS 102 916-1 V1.1.1 (2012-

39、05)8Status column The various status used in this annex are in accordance with the rules in table A.1. Table A.1: Key to status codes Status code Status name Meaning m mandatory The capability shall be supported. It is a static view of the fact that the conformance requirements related to the capabi

40、lity in the reference specification are mandatory requirements. This does not mean that a given behaviour shall always be observed (this would be a dynamic view), but that it shall be observed when the implementation is placed in conditions where the conformance requirements from the reference speci

41、fication compel it to do so. For instance, if the support for a parameter in a sent PDU is mandatory, it does not mean that it shall always be present, but that it shall be present according to the description of the behaviour in the reference specification (dynamic conformance requirement). o optio

42、nal The capability may or may not be supported. It is an implementation choice. n/a not applicable It is impossible to use the capability. No answer in the support column is required. c. conditional The requirement on the capability (“m“, “o“, “n/a“) depends on the support of other optional or condi

43、tional items. is the identifier of the conditional expression. o. qualified optional For mutually exclusive or selectable options from a set. is the identifier of the group of options, and the logic of selection of the options. Mnemonic column The Mnemonic column contains mnemonic identifiers for ea

44、ch item. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 3, are used for the support column: Y or y supported by the implementation N or n not supported by the implementation N/A, n/a or - no answer

45、 required (allowed only if the status is N/A, directly or after evaluation of a conditional status) References to items For each possible item answer (answer in the support column) within the PICS proforma there exists a unique reference, used, for example, in the conditional expressions. It is defi

46、ned as the table identifier, followed by a solidus character “/“, followed by the item number in the table. EXAMPLE: A.5/4 is the reference to the answer of item 4 in table A.5. A.1.3 Instructions for completing the PICS proforma The supplier of the implementation may complete the PICS proforma in e

47、ach of the spaces provided. More detailed instructions are given at the beginning of the different clauses of the PICS proforma. ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)9A.2 Identification of the Network Equipment Identification of the Network Equipment should be filled in so as to provide as much de

48、tail as possible regarding version numbers and configuration options. The product supplier information and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the PICS should be named as the contact person. A.2.1 Date o

49、f the statement . A.2.2 Network Equipment Under Test identification Name: . . Hardware configuration: . . . Software configuration: . . . A.2.3 Product supplier Name: . Address: . . . Telephone number: . Facsimile number: . E-mail address: . ETSI ETSI TS 102 916-1 V1.1.1 (2012-05)10Additional information: . . . A.2.4 Client Name: . Address: . . . Telephone number: . Facsimile number: . E-mail address: . Additional information: . . . A.2.5 PICS contact person Name: . Telephone number: . Facsimile number: . E-mail address