ETSI TS 102 868-3-2017 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and_1.pdf

《ETSI TS 102 868-3-2017 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 868-3-2017 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and_1.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 868-3 V1.4.1 (2017-03) Intelligent Transport Systems (ITS); Testing; Conformance test specifications for Cooperative Awareness Basic Service (CA); Part 3: Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT) floppy3TECHNICAL SPECIFICATION ETSI ETSI

2、 TS 102 868-3 V1.4.1 (2017-03)2 Reference RTS/ITS-00171 Keywords ATS, ITS, PIXIT, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture

3、 de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modi

4、fied without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. U

5、sers of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please se

6、nd your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permissio

7、n of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ET

8、SI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 868-

9、3 V1.4.1 (2017-03)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Abstract Test Method (ATM) . 8

10、g34.1 Abstract protocol tester 8g34.2 Test Configuration 8g34.3 Test architecture . 8g34.4 Ports and ASPs (Abstract Services Primitives) 9g34.4.1 Introduction. 9g34.4.2 Primitives of the camPort . 10g34.4.3 Primitives of the utPort . 10g34.5 Executing CA tests in secured mode 10g34.6 ETSI test adapt

11、er 10g35 Untestable Test Purposes 11g36 ATS conventions 11g36.1 Introduction 11g36.2 Testing conventions 11g36.2.1 Testing states 11g36.2.1.1 Initial state . 11g36.2.1.2 Final state 11g36.2.2 Message types - ASN.1 definitions . 11g36.3 Naming conventions . 12g36.3.1 Introduction. 12g36.3.2 General g

12、uidelines 12g36.3.3 ITS specific TTCN-3 naming conventions . 13g36.3.4 Usage of Log statements . 13g36.3.5 Test Case (TC) identifier 14g3Annex A (normative): TTCN-3 library modules . 15g3A.1 Electronic annex, zip file with TTCN-3 code 15g3Annex B (normative): Partial PIXIT pro forma for CA 16g3B.1 P

13、artial cancellation of copyright . 16g3B.2 Introduction 16g3B.3 Identification summary. 16g3B.4 ATS summary 16g3B.5 Test laboratory 17g3B.6 Client identification 17g3B.7 SUT 17g3B.8 Protocol layer information 18g3B.8.1 Protocol identification 18g3ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)4 B.8.2 IUT in

14、formation . 18g3Annex C (normative): PCTR pro forma for CA . 19g3C.1 Partial cancellation of copyright . 19g3C.2 Introduction 19g3C.3 Identification summary. 19g3C.3.1 Protocol conformance test report 19g3C.3.2 IUT identification . 19g3C.3.3 Testing environment . 20g3C.3.4 Limits and reservation 20g

15、3C.3.5 Comments. 20g3C.4 IUT Conformance status 20g3C.5 Static conformance summary . 21g3C.6 Dynamic conformance summary 21g3C.7 Static conformance review report . 21g3C.8 Test campaign report 22g3C.9 Observations . 23g3History 24g3ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)5 Intellectual Property Right

16、s IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential,

17、or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by

18、ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee

19、 Intelligent Transport Systems (ITS). The present document is part 3 of a multi-part deliverable covering Conformance test specifications for Cooperative Awareness Basic Service (CA) as identified below: Part 1: “Test requirements and Protocol Implementation Conformance Statement (PICS) pro forma“;

20、Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)“. The development of ITS test specifications follows the guidance provided in the ETSI EG 202 798 i.1. Therefore this ATS documentation is also ba

21、sed on the guidance provided in ETSI EG 202 798 i.1. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for t

22、he expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)6 1 Scope The present document contains the Abstract Test Suite (ATS) for Co-operative Awareness Basic Service (CA) as defined in ETSI

23、EN 302 637-2 1 in compliance with the relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 i.7. The objective of the present document is to provide a basis for conformance tests for Co-operative Awareness Basic Service (CA) equipment giving a high probability of

24、 interoperability between different manufacturers equipment. The ISO standards for the methodology of conformance testing (ISO/IEC 9646-1 i.4 and ISO/IEC 9646-2 i.5) as well as the ETSI rules for conformance testing (ETSI ETS 300 406 i.8) are used as a basis for the test methodology. 2 References 2.

25、1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendm

26、ents) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The f

27、ollowing referenced documents are necessary for the application of the present document. 1 ETSI EN 302 637-2 (V1.3.2): “Intelligent Transport Systems (ITS); Vehicular Communications; Basic Set of Applications; Part 2: Specification of Cooperative Awareness Basic Service“. 2 ETSI TS 102 868-1 (V1.4.1

28、): “Intelligent Transport Systems (ITS); Testing; Conformance test specifications for Cooperative Awareness Basic Service (CA); Part 1: Test requirements and Protocol Implementation Conformance Statement (PICS) pro forma“. 3 ETSI TS 102 868-2 (V1.4.1): “Intelligent Transport Systems (ITS); Testing;

29、Conformance test specifications for Cooperative Awareness Basic Service (CA); Part 2: Test Suite Structure and Test Purposes (TSS Users and applications requirements; Part 2: Applications and facilities layer common data dictionary“. 2.2 Informative references References are either specific (identif

30、ied by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this cla

31、use were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI EG 202 798 (V1.1.1): “Intelligent Tr

32、ansport Systems (ITS); Testing; Framework for conformance and interoperability testing“. i.2 ETSI TS 103 096-3 (V1.3.1): “Intelligent Transport Systems (ITS); Testing; Conformance test specifications for ITS Security; Part 3: Abstract Test Suite (ATS) and Protocol Implementation eXtra Information fo

33、r Testing (PIXIT)“. ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)7 i.3 ETSI TR 103 099 (V1.4.1): “Intelligent Transport Systems (ITS); Architecture of conformance validation framework“. i.4 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and

34、framework - Part 1: General concepts“. i.5 ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. i.6 ISO/IEC 9646-6 (1994): “Information technology - Open Systems Interconnection - C

35、onformance testing methodology and framework - Part 6: Protocol profile test specification“. i.7 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. i.8 ETSI ETS 300 406 (1995)

36、: “Methods for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. i.9 ETSI ES 201 873-1 (V4.5.1): “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. i.10 ET

37、SI ES 201 873-7 (V4.5.1): “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 7: Using ASN.1 with TTCN-3“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 302 637-2 1,

38、 ISO/IEC 9646-1 i.4 and ISO/IEC 9646-7 i.7 apply. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ASN Abstract Syntax Notation ASN.1 Abstract Syntax Notation One ATM Abstract Test Method ATS Abstract Test Suite BV Valid test events for Behaviour tests C

39、A Co-operative Awareness Basic Service CAM Cooperative Awareness Messages CAN Controller Area Network CRS Crash Status FMT Message FormatGFQ Generation Frequency GNSS Global Navigation Satellite System INA Information Adaptation ISO International Organization for Standardization ITS Intelligent Tran

40、sport Systems IUT Implementation Under Test LDM Local Dynamic Map MSD Message Dissemination MSG Message Generation MSP Message Processing MTC Main Test Component PCTR Protocol Conformance Testing Report PICS Protocol Implementation Conformance Statement ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)8 PIXIT

41、 Partial Protocol Implementation eXtra Information for Testing PX Pixit SAP Service Access Point SCS System Conformance Statement SCTR Static Conformance Test Report SSP Service Specific Permissions SUT System Under Test TC Test Case TI Timer testsTP Test Purposes TSS Test Suite Structure TTCN Testi

42、ng and Test Control Notation 4 Abstract Test Method (ATM) 4.1 Abstract protocol tester The abstract protocol tester used by this test suite is described in figure 1. The test system will simulate valid and invalid protocol behaviour, and will analyse the reaction of the IUT. Figure 1: Abstract proto

43、col tester - CA 4.2 Test Configuration This test suite uses a unique test configuration in order to cover the different test scenarios. In this configuration, the tester simulates one ITS station implementing the CAM protocol. 4.3 Test architecture The present document implements the general TTCN-3

44、test architecture described in ETSI EG 202 798 i.1, clauses 6.3.2 and 8.3.1. ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)9 Figure 2 shows the test architecture used for the CA ATS. The CA test component requires using only the Main Test Component (MTC). The MTC communicates with the CA SUT over the camPo

45、rt. The camPort is used to exchange CA protocol messages between the CA test component and the CA IUT. The Upper tester entity in the SUT enables triggering CA functionalities by simulating primitives from application or LDM entities. It is required to trigger the CA layer in the SUT to send CA mess

46、ages, which are resulting from upper layer primitives. Furthermore, receiving CA messages may result for the CA layer in sending primitives to the upper layer (sending Data to LDM for instance). Figure 2: Test system architecture 4.4 Ports and ASPs (Abstract Services Primitives) 4.4.1 Introduction T

47、wo ports are used by the CA ATS: The camPort, of type CamPort. The utPort, of type UpperTesterPort. ETSI ETSI TS 102 868-3 V1.4.1 (2017-03)10 4.4.2 Primitives of the camPort Two types of primitives are used in the camPort: The CamInd primitive used to receive messages of type CamPdu. The CamReq prim

48、itive used to send messages of type CamPdu. These two primitives use the CamPdu type, which is declared in the CAM.asn ASN.1 module, following the ASN.1 definition from ETSI EN 302 637-2 1. CamPdu := SEQUENCE header ItsPduHeader, cam CoopAwareness 4.4.3 Primitives of the utPort This port uses two ty

49、pes of primitives: The UtInitialize primitive used to initialize IUT. The UtTrigger primitive used trigger upper layer events in IUT. 4.5 Executing CA tests in secured mode All the CA tests, with the execption of the SSP tests, can be executed with security enabled or with security disabled. The choice of running the CA tests in secured or non-secured mode has no impact on the result of the CA tests because the test verdicts assess CA protocol behaviour only. The SSP tests can only be executed in