ETSI TS 102 868-3-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and.pdf

《ETSI TS 102 868-3-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 868-3-2015 Intelligent Transport Systems (ITS) Testing Conformance test specifications for Cooperative Awareness Basic Service (CA) Part 3 Abstract Test Suite (ATS) and.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 868-3 V1.3.1 (2015-07) Intelligent Transport Systems (ITS); Testing; Conformance test specifications for Cooperative Awareness Basic Service (CA); Part 3: Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT) floppy3TECHNICAL SPECIFICATION ETSI ETSI

2、 TS 102 868-3 V1.3.1 (2015-07)2 Reference RTS/ITS-00154 Keywords ATS, ITS, PIXIT, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture

3、 de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modi

4、fied without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. U

5、sers of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your co

6、mment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.

7、 The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo ar

8、e Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 868-3 V1.3.1 (

9、2015-07)3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Abstract Test Method (ATM) . 8g34.1 Abst

10、ract protocol tester 8g34.2 Test Configuration 8g34.3 Test architecture . 8g34.4 Ports and ASPs (Abstract Services Primitives) 9g34.4.1 Introduction. 9g34.4.2 Primitives of the camPort . 9g34.4.3 Primitives of the utPort . 10g35 Untestable Test Purposes 10g36 ATS conventions 10g36.1 Introduction 10g

11、36.2 Testing conventions 10g36.2.1 Testing states 10g36.2.1.1 Initial state . 10g36.2.1.2 Final state 10g36.2.2 Message types - ASN.1 definitions . 10g36.3 Naming conventions . 11g36.3.1 Introduction. 11g36.3.2 General guidelines 11g36.3.3 ITS specific TTCN-3 naming conventions . 12g36.3.4 Usage of

12、Log statements . 13g36.3.5 Test Case (TC) identifier 13g3Annex A (normative): TTCN-3 library modules . 14g3A.1 Electronic annex, zip file with TTCN-3 code 14g3Annex B (normative): Partial PIXIT pro forma for CA . 15g3B.1 Partial cancellation of copyright . 15g3B.2 Introduction 15g3B.3 Identification

13、 summary. 15g3B.4 ATS summary 15g3B.5 Test laboratory 15g3B.6 Client identification 16g3B.7 SUT 16g3B.8 Protocol layer information 16g3B.8.1 Protocol identification 16g3B.8.2 IUT information . 17g3ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)4 Annex C (normative): PCTR pro forma for CA 18g3C.1 Partial can

14、cellation of copyright . 18g3C.2 Introduction 18g3C.3 Identification summary. 18g3C.3.1 Protocol conformance test report 18g3C.3.2 IUT identification . 18g3C.3.3 Testing environment . 18g3C.3.4 Limits and reservation 19g3C.3.5 Comments. 19g3C.4 IUT Conformance status 19g3C.5 Static conformance summa

15、ry . 19g3C.6 Dynamic conformance summary 20g3C.7 Static conformance review report . 20g3C.8 Test campaign report 21g3C.9 Observations . 22g3History 23g3ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been

16、declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, w

17、hich is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced i

18、n ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS). The present document is part 3 of a multi-pa

19、rt deliverable covering Conformance test specification for Co-operative Awareness Basic Service (CA) as identified below: Part 1: “Test requirements and Protocol Implementation Conformance Statement (PICS) pro forma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite

20、(ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)“. The development of ITS test specifications follows the guidance provided in the ETSI EG 202 798 i.1. Therefore this ATS documentation is also based on the guidance provided in ETSI EG 202 798 i.1. Modal verbs terminology In th

21、e present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI delive

22、rables except when used in direct citation. ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)6 1 Scope The present document contains the Abstract Test Suite (ATS) for Co-operative Awareness Basic Service (CA) as defined in ETSI EN 302 637-2 1 in compliance with the relevant requirements and in accordance with

23、 the relevant guidance given in ISO/IEC 9646-7 5. The objective of the present document is to provide a basis for conformance tests for Co-operative Awareness Basic Service (CA) equipment giving a high probability of interoperability between different manufacturers equipment. The ISO standard for th

24、e methodology of conformance testing (ISO/IEC 9646-1 2 and ISO/IEC 9646-2 3) as well as the ETSI rules for conformance testing (ETSI ETS 300 406 6) are used as a basis for the test methodology. 2 References 2.1 Normative references References are either specific (identified by date of publication an

25、d/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expe

26、cted location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 E

27、TSI EN 302 637-2 (V1.3.2): “Intelligent Transport Systems (ITS); Vehicular Communications; Basic Set of Applications; Part 2: Specification of Cooperative Awareness Basic Service“. 2 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and f

28、ramework - Part 1: General concepts“. 3 ISO/IEC 9646-2 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. 4 ISO/IEC 9646-6 (1994): “Information technology - Open Systems Interconnection - Confor

29、mance testing methodology and framework - Part 6: Protocol profile test specification“. 5 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements“. 6 ETSI ETS 300 406 (1995): “Method

30、s for testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. 7 ETSI ES 201 873-1 (V4.5.1): “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 1: TTCN-3 Core Language“. 8 ETSI ES 201 873-

31、7 (V4.5.1): “Methods for Testing and Specification (MTS); The Testing and Test Control Notation version 3; Part 7: Using ASN.1 with TTCN-3“. 9 ETSI TS 102 868-1 (V1.3.1): “Intelligent Transport Systems (ITS); Testing; Conformance test specifications for Co-operative Awareness Messages (CAM); Part 1:

32、 Test requirements and Protocol Implementation Conformance Statement (PICS) proforma“. 10 ETSI TS 102 894-2 (V1.2.1): “Intelligent Transport Systems (ITS); Users and applications requirements; Part 2: Applications and facilities layer common data dictionary“. ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)7

33、 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any am

34、endments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a part

35、icular subject area. i.1 ETSI EG 202 798 (V1.1.1): “Intelligent Transport Systems (ITS); Testing; Framework for conformance and interoperability testing“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 302 637-2 1,

36、 ISO/IEC 9646-1 2 and ISO/IEC 9646-7 5 apply. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ASN Abstract Syntax Notation ASN.1 Abstract Syntax Notation One ATM Abstract Test Method ATS Abstract Test Suite BV valid test events for Behaviour tests CA Co

37、-operative Awareness Basic Service CAM Cooperative Awareness Messages CAN Controller Area Network CRS Crash Status FMT Message FormatGFQ Generation Frequency INA Information AdaptationISO International Organization for Standardization ITS Intelligent Transport Systems IUT Implementation Under Test L

38、DM Local Dynamic Map MSD Message Dissemination MSG Message Generation MSP Message Processing MTC Main Test Component PCTR Protocol Conformance Testing Report PICS Protocol Implementation Conformance Statement PIXIT Partial Protocol Implementation eXtra Information for Testing PX Pixit SAP Service Ac

39、cess Point SCS System Conformance Statement SCTR Static Conformance Test Report SUT System Under Test TC Test Case TI Timer testsTP Test Purposes TSS Test Suite Structure TTCN Testing and Test Control Notation ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)8 4 Abstract Test Method (ATM) 4.1 Abstract protoco

40、l tester The abstract protocol tester used by this test suite is described in figure 1. The test system will simulate valid and invalid protocol behaviour, and will analyse the reaction of the IUT. Figure 1: Abstract protocol tester - CA 4.2 Test Configuration This test suite uses a unique test conf

41、iguration in order to cover the different test scenarios. In this configuration, the tester simulates one ITS station implementing the CAM protocol. 4.3 Test architecture The present document implements the general TTCN-3 test architecture described in ETSI EG 202 798 i.1, clauses 6.3.2 and 8.3.1. F

42、igure 2 shows the test architecture used for the CA ATS. The CA test component requires using only the Main Test Component (MTC). The MTC communicates with the CA SUT over the camPort. The camPort is used to exchange CA protocol messages between the CA test component and the CA IUT. ETSI ETSI TS 102

43、 868-3 V1.3.1 (2015-07)9 The Upper tester entity in the SUT enables triggering CA functionalities by simulating primitives from application or LDM entities. It is required to trigger the CA layer in the SUT to send CA messages, which are resulting from upper layer primitives. Furthermore, receiving

44、CA messages may result for the CA layer in sending primitives to the upper layer (sending Data to LDM for instance). Figure 2: Test system architecture 4.4 Ports and ASPs (Abstract Services Primitives) 4.4.1 Introduction Two ports are used by the CA ATS: The camPort, of type CamPort. The utPort, of

45、type UpperTesterPort. 4.4.2 Primitives of the camPort Two types of primitives are used in the camPort: The CamInd primitive used to receive messages of type CamPdu. The CamReq primitive used to send messages of type CamPdu. ETSI ETSI TS 102 868-3 V1.3.1 (2015-07)10 These two primitives use the CamPd

46、u type, which is declared in the CAM.asn ASN.1 module, following the ASN.1 definition from ETSI EN 302 637-2 1. CamPdu := SEQUENCE header ItsPduHeader, cam CoopAwareness 4.4.3 Primitives of the utPort This port uses two types of primitives: The UtInitialize primitive used to initialize IUT. The UtTr

47、igger primitive used trigger upper layer events in IUT. 5 Untestable Test Purposes Table 1 gives a list of TPs, which are not implemented in the ATS due to the chosen ATM or other restrictions. Table 1: Untestable TP Test purpose Reason TP/CAM/MSP/BV-02 NOT implemented - No security elements in the

48、ATS 6 ATS conventions 6.1 Introduction The ATS conventions are intended to give a better understanding of the ATS but they also describe the conventions made for the development of the ATS. These conventions shall be considered during any later maintenance or further development of the ATS. The ATS

49、conventions contain two clauses, the testing conventions and the naming conventions. The testing conventions describe the functional structure of the ATS. The naming conventions describe the structure of the naming of all ATS elements. To define the ATS, the guidelines of the document ETSI ETS 300 406 6 were considered. 6.2 Testing conventions 6.2.1 Testing states 6.2.1.1 Initial state All test cases start with the function f_prInitialState. This function brings the IUT in an “initialized“ state by inv