ETSI TS 102 744-1-3-2015 Satellite Earth Stations and Systems (SES) Family SL Satellite Radio Interface (Release 1) Part 1 General Specifications Sub-part 3 Satellite Radio Interfa_1.pdf

《ETSI TS 102 744-1-3-2015 Satellite Earth Stations and Systems (SES) Family SL Satellite Radio Interface (Release 1) Part 1 General Specifications Sub-part 3 Satellite Radio Interfa_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 744-1-3-2015 Satellite Earth Stations and Systems (SES) Family SL Satellite Radio Interface (Release 1) Part 1 General Specifications Sub-part 3 Satellite Radio Interfa_1.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 744-1-3 V1.1.1 (2015-10) Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 1: General Specifications; Sub-part 3: Satellite Radio Interface Overview TECHNICAL SPECIFICATION ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 2 Reference DTS/SES-0029

2、9-1-3 Keywords 3GPP, GPRS, GSM, GSO, interface, MSS, radio, satellite, TDM, TDMA, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de

3、 Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modifie

4、d without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. User

5、s of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comme

6、nt to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. Th

7、e content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2015. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are T

8、rade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 744-1-3 V1.1.1 (2

9、015-10) 3 Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Symbols and abbreviations . 6g33.1 Symbols 6g33.2 Abbreviations . 6g34 Introduction 6g34.1 Radio interf

10、ace layering . 6g34.1.0 General 6g34.1.1 Control plane protocol stack . 7g34.1.2 User plane protocol stack 8g34.2 SDUs and PDUs . 9g35 Physical Layer 10g35.1 Shared Access Bearers . 10g35.2 Physical Layer Roles 10g35.3 Physical Layer Characteristics . 11g35.3.1 Range of Bearer Types and Subtypes . 1

11、1g35.3.2 Variable Coding Rate 11g35.3.3 Unique Words. 11g36 Bearer Control Layer operation 12g36.1 Role of the Bearer Control Layer . 12g36.2 Initial Timing Correction 13g36.3 Subsequent Timing Corrections . 13g36.4 Coding Rate and Transmit Power Adjustments 13g36.5 Admission Control . 14g36.6 Sched

12、uling 14g36.7 Packing and Unpacking of Bearer Control PDUs 14g36.8 Ciphering 14g36.9 Support for Sleep Mode . 14g36.10 Different UE Classes 14g36.11 Transmission of System Information . 14g37 Bearer Connection Layer operation 15g37.1 Role of the Bearer Connection Layer . 15g37.2 Buffering and Flow C

13、ontrol . 15g37.3 QoS Policing 15g37.4 Segmentation and Reassembly . 16g37.5 ARQ . 16g37.6 Ciphering 16g37.7 Connection QoS Parameters . 16g37.8 Connection types 16g38 Adaptation Layer operation 16g38.1 Role of the Adaptation Layer . 16g3History 18g3ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 4 Intelle

14、ctual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights

15、 (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has be

16、en carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI T

17、echnical Committee Satellite Earth Stations and Systems (SES). The present document is part 1, sub-part 3 of a multi-part deliverable. Full details of the entire series can be found in ETSI TS 102 744-1-1 i.6. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should no

18、t“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction This

19、 multi-part deliverable (Release 1) defines a satellite radio interface that provides UMTS services to users of mobile terminals via geostationary (GEO) satellites in the frequency range 1 518,000 MHz to 1 559,000 MHz (downlink) and 1 626,500 MHz to 1 660,500 MHz and 1 668,000 MHz to 1 675,000 MHz (

20、uplink). ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 5 1 Scope The present document provides an overview of the Family SL radio interface between the Radio Network Controller (RNC) and the User Equipment (UE). The Family SL radio interface operates in spectrum allocated to mobile satellite services (s

21、ee ETSI TS 102 744-2-1 i.7, clauses 5.1.2 and 6.1.2). 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references

22、, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time o

23、f publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 ETSI TS 102 744-1-4: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 1: General Specificat

24、ions; Sub-part 4: Applicable External Specifications, Symbols and Abbreviations“. 2 ETSI TS 102 744-3-6: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 6: Adaptation Layer Operation“. 2.2 Inf

25、ormative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments

26、) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular s

27、ubject area. i.1 ETSI TS 125 413: “Universal Mobile Telecommunications System (UMTS); UTRAN Iu interface Radio Access Network Application Part (RANAP) signalling (3GPP TS 25.413 Release 4)“. i.2 ETSI TS 125 301: “Universal Mobile Telecommunications System (UMTS); Radio Interface Protocol Architectur

28、e (3GPP TS 25.301 Release 4)“. i.3 ETSI TS 125 322: “Universal Mobile Telecommunications System (UMTS); Radio Link Control (RLC) protocol specification (3GPP TS 25.322 Release 4)“. i.4 ETSI TS 124 007: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System

29、 (UMTS); Mobile radio interface signalling layer 3; General Aspects (3GPP TS 24.007 Release 4)“. i.5 ETSI TS 124 008: “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); Mobile radio interface Layer 3 specification; Core network protocols; Stage

30、 3 (3GPP TS 24.008 Release 4)“. i.6 ETSI TS 102 744-1-1: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 1: General Specifications; Sub-part 1: Services and Architectures“. ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 6 i.7 ETSI TS 102 744-2-1: “Satell

31、ite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 2: Physical Layer Specifications; Sub-part 1: Physical Layer Interface“. i.8 ETSI TS 102 744-2-2: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 2: Physical

32、 Layer Specifications; Sub-part 2: Radio Transmission and Reception“. i.9 ETSI TS 102 744-3-1: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 1: Bearer Control Layer Interface“. i.10 ETSI TS

33、102 744-3-2: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 2: Bearer Control Layer Operation“. i.11 ETSI TS 102 744-3-3: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radi

34、o Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 3: Bearer Connection Layer Interface“. i.12 ETSI TS 102 744-3-4: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; S

35、ub-part 4: Bearer Connection Layer Operation“. i.13 ETSI TS 102 744-3-5: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 5: Adaptation Layer Interface“. i.14 ETSI TS 102 744-3-7: “Satellite Ea

36、rth Stations and Systems (SES); Family SL Satellite Radio Interface (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 7: NAS Layer Interface Extensions for MBMS Services“. i.15 ETSI TS 102 744-3-8: “Satellite Earth Stations and Systems (SES); Family SL Satellite Radio Interf

37、ace (Release 1); Part 3: Control Plane and User Plane Specifications; Sub-part 8: NAS Layer and User Plane Operation for MBMS Services“. 3 Symbols and abbreviations 3.1 Symbols For the purposes of the present document, the symbols given in ETSI TS 102 744-1-4 1, clause 3 apply. 3.2 Abbreviations For

38、 the purposes of the present document, the abbreviations given in ETSI TS 102 744-1-4 1, clause 3 apply. 4 Introduction 4.1 Radio interface layering 4.1.0 General The satellite radio interface is carried over a satellite link and consists of the Non-Access Stratum and Access Stratum layers. The Non-

39、Access Stratum is essentially unchanged from the UMTS Non-Access Stratum, as defined in ETSI TS 124 007 i.4 and ETSI TS 124 008 i.5, with some functional extensions to support new services, as described in ETSI TS 102 744-3-7 i.14 and ETSI TS 102 744-3-8 i.15. The Access Stratum of the satellite rad

40、io interface provides a set of services that directly support the UMTS Non-Access Stratum Control Plane entities (such as GMM and MM) and User Plane functions residing in the Core Network in the upper layers of the Mobile Terminal. ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 7 As such there are a numb

41、er of requirements on the Access Stratum protocols to ensure that the attributes of the satellite link (high delay, variable error rate, aperiodic disruptions) are countered. The satellite Access Stratum is considered as a number of communication layers, as follows: Adaptation Layer (AL); Bearer Con

42、nection Layer (BCn); Bearer Control Layer (BCt); and Physical Layer (L1). Each layer communicates with its peer, the layer above and the layer below. For each layer there are a set of protocol unit definitions which are used to communicate with the peer. In addition between each layer there are a se

43、t of interface definitions which provide the mechanisms for control and transfer of information. An overview of the main functions of each of the layers of the Access Stratum is described in the present document, with the detailed specifications for the different layers provided in the sub-parts sho

44、wn in Table 4.1. Table 4.1: Mapping of Family SL Access Stratum Layer to Part/Sub-part Family SL Access Stratum Layer Described in Sub-part Adaptation Layer (AL) ETSI TS 102 744-3-5 i.13 ETSI TS 102 744-3-6 2 Bearer Connection Layer (BCn) ETSI TS 102 744-3-3 i.11 ETSI TS 102 744-3-4 i.12 Bearer Cont

45、rol Layer (BCt) ETSI TS 102 744-3-1 i.9 ETSI TS 102 744-3-2 i.10 Physical Layer (L1) ETSI TS 102 744-2-1 i.7 ETSI TS 102 744-2-2 i.8 4.1.1 Control plane protocol stack The Control Plane of the protocol stack is shown in Figure 4.1. The Access Stratum and the Non-Access Stratum are separately indicat

46、ed in the diagram. The parts of the protocol stack that are modified for the Family SL satellite link relative to the standard 3GPP protocols are described in ETSI TS 102 744-1-1 i.6, clause 6. Figure 4.1: Control Plane Protocol Stack Layering ETSI ETSI TS 102 744-1-3 V1.1.1 (2015-10) 8 4.1.2 User p

47、lane protocol stack The protocol stack for the User Plane of the Packet Switched Domain is shown in Figure 4.2. Figure 4.2: Packet Switched User Plane Protocol Stack Layering For the Circuit Switched Domain, the lower layers (L1, BCt and BCn) of the protocol stack are identical, however, the PDCP an

48、d PPP/IP layers are replaced by the appropriate entity to provide Circuit Switched Services (e.g. Voice Codec or ISDN Interworking Function). Figure 4.3 illustrates the user plane protocol stack for the Circuit Switched domain. Figure 4.3: Circuit Switched User Plane Protocol Stack Layering ETSI ETS

49、I TS 102 744-1-3 V1.1.1 (2015-10) 9 4.2 SDUs and PDUs Each of the layers exchanges a set of Protocol Data Units (PDUs) with its peer using the capabilities of the lower layers to transport each PDU. Each of the peer-layer entities exchanges a sequence of control messages called Signalling Data Units (SDUs) for the purpose of establishing, maintaining and terminating a connection. SDUs are always encapsulated within a Protocol Data Unit (PDU). Each Protocol Data Unit may contain a higher layer PDU and/