ETSI TS 101 811-3-3-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the packet based convergence layer Part 3 IEEE 1394 Service Specific Converg_1.pdf

《ETSI TS 101 811-3-3-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the packet based convergence layer Part 3 IEEE 1394 Service Specific Converg_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 811-3-3-2004 Broadband Radio Access Networks (BRAN) HIPERLAN Type 2 Conformance testing for the packet based convergence layer Part 3 IEEE 1394 Service Specific Converg_1.pdf（82页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 811-3-3 V1.3.1 (2004-08)Technical Specification Broadband Radio Access Networks (BRAN);HIPERLAN Type 2;Conformance testing for the packet based convergence layer;Part 3: IEEE 1394 Service Specific Convergence Sublayer (SSCS);Sub-part 3: Abstract Test Suite (ATS) specificationfloppy3 ETS

2、I ETSI TS 101 811-3-3 V1.3.1 (2004-08) 2 Reference RTS/BRAN-0024TB4-3-3 Keywords access, ATS, HIPERLAN, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregi

3、stre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in content

4、s between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document

5、may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editoretsi.org Copyright Notification No part may be reprodu

6、ced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members

7、. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 3 Contents Intellectual Propert

8、y Rights6 Foreword.6 1 Scope 7 2 References 7 3 Definitions and abbreviations.8 3.1 Definitions8 3.2 Abbreviations .8 4 Abstract Test Method (ATM).9 4.1 Test architecture .9 4.1.1 Normal architecture for AP or MT .9 4.1.2 Specific architecture for HL2 Bus system (AP/CC-IRM or MT/WT)10 4.2 Test Confi

9、gurations 10 4.2.1 Test Configurations for MT10 4.2.2 Test Configurations for AP.11 4.2.3 Test Configurations for AP/CC-IRM11 4.2.4 Test Configurations for 1394 Talker.12 4.2.5 Test Configurations for 1394 Listener13 5 Untestable Test Purposes (TP) .13 6 ATS conventions13 6.1 Naming conventions.14 6

10、.1.1 Declarations part.14 6.1.1.1 General14 6.1.1.2 Test suite operations definition .14 6.1.1.3 Test suite parameter declarations 14 6.1.1.4 Test case selection expression definition 14 6.1.1.5 Test suite constant declarations.14 6.1.1.6 Test suite variable declarations .14 6.1.1.7 Test case variab

11、le declarations15 6.1.1.8 Timer declarations.15 6.1.1.9 ASP type definitions .15 6.1.1.10 PDU type definitions.15 6.1.1.11 CM type definitions.15 6.1.1.12 Alias definitions 15 6.1.2 Constraints part.15 6.1.2.1 General15 6.1.3 Dynamic part 16 6.1.3.1 General16 6.1.3.2 Test Case (TC) identifier.16 6.1

12、.3.3 Test step identifier.16 6.1.3.4 Default identifier .16 6.1.3.5 Label identifier16 6.1.3.6 ATS abbreviations.17 6.2 Implementation conventions 17 6.2.1 Declaration part 17 6.2.2 Constraint part 17 6.2.3 Dynamic part 18 7 Abstract testing service primitives .18 7.1 Tester primitives.18 7.2 C-plan

13、e primitives 18 7.3 U-plane primitives18 Annex A (normative): Abstract Test Suite (ATS) .19 ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 4 A.1 The TTCN Graphical form (TTCN.GR) 19 A.2 The TTCN Machine Processable form (TTCN.MP)19 Annex B (normative): Partial PIXIT proforma for TS 101 493-3 - MT part.20

14、 B.1 Identification summary.20 B.2 ATS summary 20 B.3 Test laboratory20 B.4 Client identification21 B.5 SUT 21 B.6 Protocol layer information21 B.6.1 Protocol identification 21 B.6.2 IUT information .22 Annex C (normative): Partial PIXIT proforma for TS 101 493-3 - AP part35 C.1 Identification summa

15、ry.35 C.2 ATS summary 35 C.3 Test laboratory35 C.4 Client identification36 C.5 SUT 36 C.6 Protocol layer information36 C.6.1 Protocol identification 36 C.6.2 IUT information .37 Annex D (normative): Partial PIXIT proforma for TS 101 493-3 - HL2 Bus system part50 D.1 Identification summary.50 D.2 ATS

16、 summary 50 D.3 Test laboratory50 D.4 Client identification51 D.5 SUT 51 D.6 Protocol layer information51 D.6.1 Protocol identification 51 D.6.2 IUT information .52 Annex E (normative): PCTR Proforma for TS 101 493-3 - MT part65 E.1 Identification summary.65 E.1.1 Protocol conformance test report65

17、E.1.2 IUT identification.65 E.1.3 Testing environment.65 E.1.4 Limits and reservation66 E.1.5 Comments.66 E.2 IUT Conformance status 66 E.3 Static conformance summary .66 E.4 Dynamic conformance summary66 E.5 Static conformance review report.67 E.6 Test campaign report68 E.7 Observations.69 ETSI ETS

18、I TS 101 811-3-3 V1.3.1 (2004-08) 5 Annex F (normative): PCTR Proforma for TS 101 493-3 - AP part.70 F.1 Identification summary.70 F.1.1 Protocol conformance test report70 F.1.2 IUT identification.70 F.1.3 Testing environment.70 F.1.4 Limits and reservation71 F.1.5 Comments.71 F.2 IUT Conformance st

19、atus 71 F.3 Static conformance summary .71 F.4 Dynamic conformance summary71 F.5 Static conformance review report.72 F.6 Test campaign report73 F.7 Observations.74 Annex G (normative): PCTR Proforma for TS 101 493-3 - HL2 Bus system part 75 G.1 Identification summary.75 G.1.1 Protocol conformance te

20、st report75 G.1.2 IUT identification.75 G.1.3 Testing environment.75 G.1.4 Limits and reservation76 G.1.5 Comments.76 G.2 IUT Conformance status 76 G.3 Static conformance summary .76 G.4 Dynamic conformance summary76 G.5 Static conformance review report.77 G.6 Test campaign report77 G.6.1 AP/CC-IRM

21、.77 G.6.2 1394 controller .78 G.6.3 1394 talker78 G.6.4 1394 listener .79 G.7 Observations.80 Annex H (informative): Bibliography.81 History 82 ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been decla

22、red to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which

23、is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not r

24、eferenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document is part 3, sub-part 3 of a

25、 multi-part deliverable. Full details of the entire series can be found in part 1, sub-part 1 (see bibliography). ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 7 1 Scope The present document contains the Test Suite Structure (TSS) and Test Purposes (TP) to test the BRAN HIPERLAN type 2; Packet based Con

26、vergence Layer; Part 3: IEEE 1394 Service Specific Convergence Sublayer (SSCS). The objective of the present document is to provide a basis for conformance tests for BRAN HIPERLAN type 2 equipment giving a high probability of air interface inter-operability between different manufacturers BRAN HIPER

27、LAN type 2 equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 4 and ISO/IEC 9646-2 5) as well as the ETSI rules for conformance testing (ETS 300 406 3) are used as a basis for the test methodology. Annex A provides the Tree and Tabular Combined Notation (TTCN) par

28、t of the ATS. Annex B provides the Partial Protocol Implementation Extra Information for Testing (PIXIT) Proforma of the MT side ATS. Annex C provides the Partial Protocol Implementation Extra Information for Testing (PIXIT) Proforma of the AP side ATS. Annex D provides the Protocol Conformance Test

29、 Report (PCTR) Proforma of the MT side ATS. Annex E provides the Protocol Conformance Test Report (PCTR) Proforma of the AP side ATS. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either sp

30、ecific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected

31、 location might be found at http:/docbox.etsi.org/Reference. 1 ETSI TS 101 493-3 (V1.2.1): “Broadband Radio Access Networks (BRAN); HIPERLAN Type 2; Packet based Convergence Layer; Part 3: IEEE 1394 Service Specific Convergence Sublayer (SSCS)“. 2 ETSI TS 101 823-2-3: “Broadband Radio Access Network

32、s (BRAN); HIPERLAN Type 2; Conformance testing for the Data Link Control (DLC) layer; Part 2: Radio Link Control (RLC) sublayer; Sub-part 3: Abstract Test Suite (ATS) specification“. 3 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specificat

33、ions; Standardization methodology“. 4 ISO/IEC 9646-1 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. (See also ITU-T Recommendation X.290 (1995). 5 ISO/IEC 9646-2 (1994): “Information technology - Open System

34、s Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. (See also ITU-T Recommendation X.291 (1995). 6 ISO/IEC 9646-3 (1998): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 3: The T

35、ree and Tabular Combined Notation (TTCN)“. (See also ITU-T Recommendation X.292 (2002). ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 8 7 ISO/IEC 9646-6 (1994): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 6: Protocol profile test specific

36、ation“. 8 ISO/IEC 9646-7 (1995): “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statement“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions

37、 given in ISO/IEC 9646-7 8 and TS 101 493-3 1 apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations defined in ISO/IEC 9646-1 4, ISO/IEC 9646-6 7, ISO/IEC 9646-7 8, TS 101 493-3 1 and the following apply: ACH Access feedback CHannel AP Access Point APT Access Point Tra

38、nsceiver ARQ Automatic Repeat Request ASP Abstract Service Primitive ATM Abstract Test Method ATS Abstract Test Suite ATSP Abstract Testing Service Primitives BCH Broadcast CHannel BI Invalid BehaviourBO Inopportune Behaviour BV Valid Behaviour CA Capability tests CC Central Controller CL Convergenc

39、e Layer CPCS Common Part Convergence Sublayer DFS Dynamic Frequency Selection DLC Data Link Control DM Direct Mode DUC DLC User Connection IUT Implementation Under Test LCH Long CHannel LT Lower TesterMAC Medium Access Control MAC-ID MAC IDentifier MT Mobile Terminal PCO Point of Control and Observa

40、tion PCTR Protocol Conformance Test Report PDU Protocol Data Unit PHY Physical layer PICS Protocol Implementation Conformance Statement PIXIT Protocol Implementation eXtra Information for Testing RLC Radio Link Control RSS Received Signal Strength SAP Service Access Point SCH Short CHannel SSCS Serv

41、ice Specific Convergence Sublayer SUT System Under Test TC Test Cases TP Test Purposes ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 9 TSS Test Suite Structure TTCN Tree and Tabular Combined Notation UT Upper Tester 4 Abstract Test Method (ATM) This clause describes the ATM used to test the HIPERLAN 2 I

42、EEE 1394 Service Specific Convergence Sublayer (SSCS) at the AP side and at the MT side. 4.1 Test architecture 4.1.1 Normal architecture for AP or MT PHYDLC/MACDLC/MACLower TesterPHYS UTARQRLCRLC ARQCL (IUT)C LC PCOCL (ATS)SARIN IT.C LU PCONotional UTLoopbackFigure 1: Test architecture for TS101 493

43、-3 A single-party testing concept is used, which consists of the following abstract testing functions: Lower Tester: A Lower Tester (LT) is located in the remote BRAN H/2 test system. It controls and observes the behaviour of the IUT. CL ATS: A Convergence Layer (CL) Abstract Test Suite (ATS) is loc

44、ated in the remote BRAN H/2 test system. Contains part of SSCS functionalities for establishing a U-plane connection needed for testing CL common part behaviour. CLU PCO: U-plane. The first Point of Control and Observation (PCO) for Convergence Layer testing is located at a SAR_SAP between the Commo

45、n Part Convergence Sublayer (CPCS) and the SAR sub-layer. All test events at the PCO are specified in terms of Abstract Testing Service Primitives (ATSP defined in clause 7) containing complete SAR SDU. CLC PCO: C-plane. The secondPoint of Control and Observation (PCO) for Convergence Layer testing

46、is located at a SAP between the Service Specific Convergence Sub-layer (SSCS) and the DLC layer. All test events at the PCO are specified in terms of Abstract Testing Service Primitives (ATSP defined in clause 7) containing complete DLC SDU. To avoid the complexity of data fragmentation and recombin

47、ation testing, the SAP is defined below these functions. SAR: The Segmentation and Reassembly sub-layer of the Convergence layer - Common Part is implemented in the test system outside the ATS. This allows implicit testing of the IUTs SAR entity without any internal requirement of its implementation

48、. INIT.: Part of a generic SSCS has to be simulated as an initialization process by the ATS to provide the establishment of the U-plane needed for convergence layer testing. ETSI ETSI TS 101 811-3-3 V1.3.1 (2004-08) 10Notional UT: No explicit upper tester (UT) exists in the system under test. Nevert

49、heless, some specific actions to cover implicit send events and to obtain feedback information are necessary for the need of the test procedures. A black box covering these requirements is used in the SUT as a notional UT as defined in ISO 9646. This notional UT is part of the test system. 4.1.2 Specific architecture for HL2 Bus system (AP/CC-IRM or MT/WT) PHY DLC/MAC DLC/MAC Lower Tester PHY ARQ RLC RLC ARQ CL (IUT) HL2 Bus (ATS) CL PCO 1394 Application 1394 SSCS +PBCL CLC PCO Figure 2: Test architecture for HL2 Bus system A single-