ETSI EN 301 213-1-2002 Fixed Radio Systems Point-to-Multipoint Equipment Point-to-Multipoint Digital Radio Systems in Frequency Bands in the Range 24 25 GHz to 29 5 GHz Using Diffe.pdf

《ETSI EN 301 213-1-2002 Fixed Radio Systems Point-to-Multipoint Equipment Point-to-Multipoint Digital Radio Systems in Frequency Bands in the Range 24 25 GHz to 29 5 GHz Using Diffe.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 213-1-2002 Fixed Radio Systems Point-to-Multipoint Equipment Point-to-Multipoint Digital Radio Systems in Frequency Bands in the Range 24 25 GHz to 29 5 GHz Using Diffe.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、ETSI EN 301 21 3-1 VI .I .2 (2002-02) European Sfandard (Telecommunicafions series) Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 1: Basic parameters 2 ETSI EN 3

2、01 213-1 V1.1.2 (2002-02) Reference REN/TM-04124 Keywords DRRS, multipoint, radio, RLL, transmission ETSI 650 Route des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la So

3、us-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloaded from: http:l/w.etsi .orq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between

4、 such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be su

5、bject to revision or change of status. Information on the current status of this and other ETSI documents is available at 3 If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written permission. The copyright

6、and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 2002. All rights reserved. ETSI 3 ETSI EN 301 213-1 V1.1.2 (2002-02) Contents Intellectual Property Rights . .5 Foreword . 5 Introduction . .6 1 2 3 3.1 3.2 3.3 4 4.1 4.2 4.2.1 4.2.2

7、4.3 4.4 4.4.1 4.4.2 4.5 4.6 4.7 4.8 4.9 4.9.1 4.9.2 4.9.3 5 5.1 5.2 5.3 5.4 5.5 5.5.1 5.5.2 5.5.3 5.5.3.1 5.5.3.2 5.5.3.3 5.5.4 5.5.5 5.5.6 5.5.7 5.6 5.6.1 5.6.2 5.6.3 5.7 5.7.1 5.7.2 5.7.3 5.7.4 5.7.4.1 5.7.4.2 Scope 7 ieferences . .8 Iefinitions, symbols and abbreviations . 11 Definitions . . 11 S

8、ymbols . . 11 Abbreviations . 11 3eneral characteristics .13 General system architecture . 13 Frequency bands and channel arrangements . . 14 Channel plan . 14 Channel arrangements . 14 Compatibility requirements . . 14 Environmental conditions . 14 Equipment for non-weather protected locations (out

9、door locations). .15 Power supply . . 15 Electromagnetic compatibility conditions . . 15 TMN interfaces . . 15 Synchronization of interface bit rates. . . 15 Branching/feeder/antenna requirements . 15 Wave guide flanges . 16 Return loss . . 16 Intermodulation products . . 16 system parameters. .16 S

10、ystem capacity. . 16 Round trip delay . 16 Transparency . . 17 Voice coding methods . . 17 Transmitter characteristics. . 17 Transmitter output power. . 17 Transmitter nominal output power . . 18 Transmit power and frequency control . 18 Automatic Transmit Power Control (ATPC) . 18 Remote Transmit P

11、ower Control (RTPC) . 18 Remote Frequency Control (RFC) . . 18 RF spectrum mask . . 18 Tx Local Oscillator frequency arrangements . . 18 Spurious emissions (external) . 19 Radio frequency tolerance . . 19 Receiver characteristics. . 19 Rx Local Oscillator frequency arrangements . . 19 Spurious emiss

12、ions . 19 Receiver IF 19 System performance . 19 Dynamic level range . 19 Equipment Background BER . 19 Interference sensitivity . . 20 Adjacent channel interference . 20 Equipment within weather protected locations . 14 . . BER as a function of Rece . 19 Co-channel interferenc . 20 ETSI 4 ETSI EN 3

13、01 213-1 V1.1.2 (2002-02) Continuous Wave (CW) interference 20 5.7.4.3 5.7.5 Distortion sensitivity . 20 6 Types of interfaces at the subscriber equipment and the network exchange 21 Annex A (informative): Bibliography . 22 . History 23 ETSI 5 ETSI EN 301 213-1 V1.1.2 (2002-02) Intellectual Property

14、 Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 314: “Intellectual Property Rights (7PRs); Essen

15、tial, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (5). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaran

16、tee can be given as to the existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Commit

17、tee Transmission and Multiplexing (TM). The present document contains the minimum technical requirements to ensure compatibility of products and conformance with radio regulations across ETSI member states. Radio equipment from different manufacturers are not required to interwork at radio frequency

18、 (i.e. no common air interface). The present document defines the requirements for radio-relay equipment and associated interfaces. The present document is intended to cover a variety of systems designed for a variety of services, applications, performance objectives and deployment conditions. There

19、fore it is necessary if applicable to include in the present document different sets of system parameters. In the present document these sets of parameters are referred to as “system types“. The present document is part 1 of a multipart deliverable covering the Point-to-multipoint equipment; Point-t

20、o-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods. as identified below: Part 1: “Basic parameters“; Part 2: Part 3 : Part 4: Part 5: “Frequency Division Multiple Access (FDMA) methods“; “Time Division Multiple Access (TDMA) method

21、s“; “Direct Sequence Code Division Multiple Access (DS-CDMA) methods“; “Multi-Carrier Time Division Multiple Access (MC-TDMA) methods“. Parts 2,3,4 and 5 are intended to be used in conjunction with the present document, describing the basic parameters common to all access methods. References in EN 3

22、01 213 parts 2 4, 3 5, 4 6 and 5 7 to technical parameters for P-MP systems apply equally to MP-MP systems. A basic description of the different access methods and a comparison among them are provided in TR 101 274 SI. The present version differs from the previous one for editorial up-dating consequ

23、ent to the publication of new ERC Recommendations for FWA in these bands, to publication of EN 301 213-4 6 and EN 301 213-5 7 and to recent terminology used in the other parts of the present document. Moreover, alignment to the recent status of EMC ENS harmonized under R - concentration; - transpare

24、ncy. Radio is often the ideal way of obtaining communications at low cost and almost independent of distance, and difficult topography. Moreover, a small number of sites are required for these installations, thus facilitating rapid implementation and minimizing maintenance requirements of the system

25、s. Concentration means that m subscribers can share n radio channels (m being larger than n), allowing a better use to be made of the available frequency spectrum and at a lower equipment cost. The term “multi-access“ derives from the fact that every subscriber has access to every channel (instead o

26、f a fixed assignment as in most multiplex systems). When a call is initiated one of the available channels is allocated to it. When the call is terminated, the channel is released for another call. Concentration requires the use of distributed intelligent control which in turn allows many other oper

27、ations and maintenance functions to be added. Transparency means that the exchange (service node) and the subscriber equipment communicate with each other without being aware of the radio link. ETSI 7 ETSI EN 301 213-1 V1.1.2 (2002-02) 1 Scope The present document specifies the minimum requirements

28、for system parameters of Point-to-Multipoint (P-MP) Radio and Multipoint-to-Multipoint (MP-MP) Systems in the terrestrial Fixed Services (FS) operating in the bands 24,5 GHz to 29.5 GHz. Multipoint (MP) Radio-Relay Systems use in principle three different access methods, taking into account the basi

29、c physical parameters of the frequency, the code and the time. This leads to the three basic access methods of: - - - Frequency Division Multiple Access (FDMA); Code Division Multiple Access (CDMA); Time Division Multiple Access (TDMA). In addition, in particular for wide-band applications, a multi-

30、carrier transmission implementation may be applied, where each sub-carrier uses one of the above access methodologies. It should be noted that MP-MP systems differ from P-MP systems in that Terminal Stations may be connected directly to one another in a series of short links and generally act as rep

31、eaters for traffic carried on to other stations. The arrangement of links varies over time to accommodate changes in propagation characteristics and changes in the subscriber base. The MP system in the band 24,5 GHz to 29,5 GHz (ERC/REC T/R 13-02 i) will provide access to both public and private net

32、works (PSTN, PDN, etc.) by means of the various standardized network interfaces (e.g. 2-wire loop and ISDN ranging from basic rate to n x 2 Mbit/s as well as local area to wide area data networks interfaces). The system may be applied to build new access networks by means of a multi cellular archite

33、cture, covering urban and suburban areas. MP systems are generally configured as Pre-Assigned Multiple Access (PAMA) or as Demand Assigned Multiple Access (DAMA) Radio Systems. The present document covers the following MP applications: - voice; - fax; - voice band data; - telex; related to analogue

34、interfaces; and - 64 kbit/s; - ISDN; - digital video; - digital audio; - Internet access; related to digital interfaces; - further applications like ATM, Frame Relay, LAN, WAN may also be provided. The equipment covered by EN 301 213 should be designed to be able to meet the network performance requ

35、irements foreseen by ITU-R Recommendations F.696-2 9 and F.697-2 lo, for medium and local grade portion or ITU-R Recommendation F. 1189-1 i 11 for the national portion (access or short haul) of the digital connection following the criteria defiied in ITU-T Recommendation(s) G.821 12 andor G.826 13.

36、The availability requirements are under further study by the relevant bodies. ETSI 8 ETSI EN 301 213-1 V1.1.2 (2002-02) Network operators may choose different performance and availability requirements in order to extend the possible area of application thus fitting to their network needs. Radio term

37、inals from different manufacturers are not intended to interwork at radio frequency (i.e. no common air interface). Regulatory bodies should take into account the inband coexistence between MP systems using differing access methods. The present document defines the requirements of radio terminal and

38、 radio-relay equipment including the interfaces. The requirements for multiplex, network management and antenna/feeder equipment may be addressed elsewhere. 2 Re fe re nces The following documents contain provisions which, through reference in this text, constitute provisions of the present document

39、. References are either specific (identified by date of publication andor edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. il ERC/REC T/R 13-02, annex B and annex C: “Preferred ch

40、annel arrangements for fixed services in the range 22,O - 29,5 GHz“. ERC/REC 00-05: “Use of the band 24.5 - 26.5 GHz for fixed wireless access“. ERC/REC 01-03: “Use of parts of the band 27.5 - 29.5 GHz for Fixed Wireless Access (FWA)“ ETSI EN 301 213-2: “Fixed Radio Systems; Point-to-multipoint equi

41、pment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 2: Frequency Division Multiple Access (FDMA) methods“. ETSI EN 301 213-3: “Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio

42、 systems in frequency bands in the range 24,25 GHz to 29,5 GHz using different access methods; Part 3: Time Division Multiple Access (TDMA) methods“. ETSI EN 301 213-4: “Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,2

43、5 GHz to 29,5 GHz using different access methods; Part 4: Direct Sequence Code Division Multiple Access (DS-CDMA) methods“. ETSI EN 301 213-5: “Fixed Radio Systems; Point-to-multipoint equipment; Point-to-multipoint digital radio systems in frequency bands in the range 24,25 GHz to 29,5 GHz using di

44、fferent access methods; Part 5: Multi-Carrier Time Division Multiple Access (MC-TDMA) methods“. ETSI TR 101 274: “Transmission and Multiplexing (TM); Digital Radio Relay Systems (DRRS); Point-to-multipoint DRRS in the access network: Overview of different access techniques“. ITU-R Recommendation F.6

45、96-2: “Error performance and availability objectives for hypothetical reference digital sections forming part or all of the medium-grade portion of an ISDN connection at a bit rate below the primary rate utilizing digital radio-relay systems“. 21 31 41 51 61 71 SI 91 ITU-R Recommendation F.697-2: “E

46、rror performance and availability objectives for the local- grade portion at each end of an ISDN connection at a bit rate below the primary rate utilizing digital radio-relay systems“. ITU-R Recommendation F. 1 189- 1 : “Error performance objectives for constant bit rate digital paths at or above th

47、e primary rate carried by digital radio-relay systems which may form part or all the national portion of a 27 500 km hypothetical reference path“. ETSI 9 ETSI EN 301 213-1 V1.1.2 (2002-02) i131 i141 i151 i161 i171 i181 i191 i201 i221 i231 i241 i251 i261 i271 i281 i291 i301 i3 11 i321 i331 ITU-T Reco

48、mmendation G. 82 1 : “Error performance of an international digital connection operating at a bit rate below the primary rate and forming part of an integrated services digital network“. ITU-T Recommendation G. 826: “Error performance parameters and objectives for international, constant bit rate di

49、gital paths at or above the primary rate“. ETSI ETS 300 O 19: “Equipment Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment“. ETSI EN 300 385: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for fixed radio links and ancillary equipment“ ETSI EN 301 489-1 : “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1 : Common technical requirements“. ETSI EN