EN ISO 17074-2011 en Leather - Physical and mechanical tests - Determination of resistance to horizontal spread of flame《皮革 物理和机械试验 火焰抗水平传播性的测定》.pdf

《EN ISO 17074-2011 en Leather - Physical and mechanical tests - Determination of resistance to horizontal spread of flame《皮革 物理和机械试验 火焰抗水平传播性的测定》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 17074-2011 en Leather - Physical and mechanical tests - Determination of resistance to horizontal spread of flame《皮革 物理和机械试验 火焰抗水平传播性的测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 17074:2011Leather Physical andmechanical tests Determination of resistance tohorizontal spread of flame (ISO17074:2006)BS EN ISO 17074:2011 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN ISO17074:2011. It is identical to ISO 17074:2006. It supersedes BS EN14326:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee TCI/69, Footwear, leather and coated fabrics.A list of organization

3、s represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 72289 9ICS 13.220.40; 59.140.30Compliance with a British Standar

4、d cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17074 September 2011

5、 ICS 59.140.30 Supersedes EN 14326:2003English Version Leather - Physical and mechanical tests - Determination of resistance to horizontal spread of flame (ISO 17074:2006) Cuir - Essais physiques et mcaniques - Dtermination de la rsistance la propagation horizontale de la flamme (ISO 17074:2006) Led

6、er - Physikalische und mechanische Prfungen - Bestimmung der Widerstandsfhigkeit gegen die horizontale Ausbreitung von Flammen (ISO 17074:2006) This European Standard was approved by CEN on 18 August 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the

7、conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard e

8、xists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national

9、standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland

10、and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO

11、17074:2011: EBS EN ISO 17074:2011EN ISO 17074:2011 (E) 3 Foreword The text of ISO 17074:2006 has been prepared by International Union of Leather Technologists and Chemists Societies and has been taken over as EN ISO 17074:2011 by Technical Committee CEN/TC 289 “Leather” the secretariat of which is h

12、eld by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at the latest by March 2012. Attention is drawn to the possibility tha

13、t some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14326:2003. According to the CEN/CENELEC Internal Regulations, the national standards organizations

14、 of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R

15、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 17074:2006 has been approved by CEN as a EN ISO 17074:2011 without any modification. BS EN ISO 17074:2011ISO 17074:2006(E) IULTCS/IUP 47:2006(E) ISO 2006 All rights reserved iiiForeword

16、ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical

17、committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of elect

18、rotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the

19、member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ident

20、ifying any or all such patent rights. ISO 17074 was prepared by the Physical Test Commission of the International Union of Leather Technologists and Chemists Societies (IUP Commission, IULTCS) in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/TC 289, Leat

21、her, the secretariat of which is held by UNI. It was published as EN 14326. It is based on IUP 47 published in J. Soc. Leather Tech. Chem., 86 (7), p. 359, 2002, and declared an official method of the IULTCS in May 2003. IULTCS, originally formed in 1897, is a world-wide organization of professional

22、 leather societies to further the advancement of leather science and technology. IULTCS has three Commissions, which are responsible for establishing international methods for the sampling and testing of leather. ISO recognizes IULTCS as an international standardizing body for the preparation of tes

23、t methods for leather. BS EN ISO 17074:2011BS EN ISO 17074:2011INTERNATIONAL STANDARD ISO 17074:2006(E)IULTCS/IUP 47:2006(E) ISO 2006 All rights reserved 1Leather Physical and mechanical tests Determination of resistance to horizontal spread of flame 1 Scope This International Standard specifies a m

24、ethod for determining the horizontal burning rate of leather. It is applicable to all light leathers but is particularly intended for leathers used in the passenger compartment of motor vehicles. NOTE The method uses the apparatus specified in ISO 3795 but incorporates special provisions for samplin

25、g, conditioning and testing of leather. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendme

26、nts) applies. ISO 2418, Leather Chemical, physical and mechanical and fastness tests Sampling location ISO 2419, Leather Physical and mechanical tests Sample preparation and conditioning ISO 2589, Leather Physical and mechanical tests Determination of thickness ISO 3795:1989, Road vehicles, and trac

27、tors and machinery for agriculture and forestry Determination of burning behaviour of interior materials 3 Principle A test piece is held horizontally in a U-shaped holder and is exposed to a defined flame for a specified time with the flame acting on the free end of the test piece. The time is reco

28、rded for the flame to self-extinguish or to burn a measured distance. 4 Apparatus 4.1 Combustion chamber, as specified in 5.1 of ISO 3795:1989. 4.2 Test piece holder, as specified in 5.2 of ISO 3795:1989. 4.3 Gas burner, as specified in 5.3 of ISO 3795:1989. 4.4 Test gas, calorific value approximate

29、ly 38 MJ/m3, (e.g. natural gas). 4.5 Stop watch, reading to 0,5 s. BS EN ISO 17074:2011ISO 17074:2006(E) IULTCS/IUP 47:2006(E) 2 ISO 2006 All rights reserved4.6 Thickness gauge, conforming to ISO 2589. 4.7 Ruler, reading to 1 mm. 4.8 Fume cupboard, as specified in 5.7 of ISO 3795:1989. 5 Sampling an

30、d sample preparation 5.1 Sample in accordance with ISO 2418. 5.2 Prepare three test pieces of the form and dimensions shown in Figure 1 with the long edge of the test piece being parallel to the backbone. NOTE If there is a requirement for more than two hides or skins to be tested in one batch, then

31、 only one sample need be taken from each hide or skin, provided that the overall total is not less than three test pieces. Dimensions in millimetres Figure 1 Test piece 5.3 Condition the test pieces in accordance with ISO 2419. The test pieces should be maintained under these conditions until immedi

32、ately prior to testing. 6 Procedure 6.1 Determine the thickness of the test piece in accordance with ISO 2589. 6.2 Place the test piece in the holder (4.2) so that the exposed side will be downwards to the flame. 6.3 Light the burner, close the air inlet and adjust the flame to a height of 38 mm 1 m

33、m using the mark in the chamber (4.1). Allow the flame to burn for at least 5 min while the gas flow stabilises. 6.4 Push the test piece holder (4.2) into the combustion chamber (4.1) so that the left hand end of the test piece (Figure 1) is exposed to the flame. After 15,0 s 0,5 s, extinguish the f

34、lame by turning off the gas supply to the burner. 6.5 Allow any flame on the leather to propagate along the test piece, observing the flame on the side where the flame is burning faster. BS EN ISO 17074:2011ISO 17074:2006(E) IULTCS/IUP 47:2006(E) ISO 2006 All rights reserved 36.6 Note the time when

35、the foot of the flame passes the first measuring points which are the holes at the left hand end of the test piece in Figure 1. Allow the flame to continue and note the time when the flame reaches the last measuring points which are the holes at the right hand end of the test piece in Figure 1. If t

36、he flame self-extinguishes before reaching the last measuring point, note the time when it self-extinguishes. 6.7 Using the ruler (4.7), measure the burnt distance up from the first measuring point to either the last measuring point or the point where the flame self-extinguishes. Burnt distance is t

37、he decomposed part of the test piece, which is destroyed on its surface or in the interior by burning. 6.8 If the sample does not ignite, does not continue burning when the flame is removed or self-extinguishes before reaching the first measuring point, then the burning rate is 0 mm/min. 6.9 Allow t

38、he combustion chamber to cool to less than 30 C before further tests are carried out. 7 Expression of results Calculate the burning rate, B, in millimetres per minute, using the formula: 60dBt= where d is the burnt distance, in millimetres; t is the time, in seconds, to burnt distance, d. 8 Test rep

39、ort The test report shall include the following: a) a reference to this International Standard, i.e. ISO 17074:2006; b) the mean thickness of the test pieces; c) the mean value of the burning rate in millimetres per minute (mm/min); d) the standard atmosphere used for conditioning and testing as giv

40、en in ISO 2419 (i.e. 20 C/65 % RH, or 23 C/50 % RH); e) any deviations from the method specified in this International Standard; f) full details for identification of the sample and any deviations from ISO 2418 with respect to sampling. This page deliberately left blankThis page deliberately left bl

41、ankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI

42、)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim

43、of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)

44、20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of st

45、andards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it i

46、s BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax:

47、+44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discount

48、s on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a re