EN ISO 16583-2002 en Open end blind rivets with break pull mandrel and countersunk head - Cu St or Cu Br or Cu SSt《开口型沉头抽芯盲铆钉 Cu St或Cu Br或Cu SSt ISO 16583-2002》.pdf

《EN ISO 16583-2002 en Open end blind rivets with break pull mandrel and countersunk head - Cu St or Cu Br or Cu SSt《开口型沉头抽芯盲铆钉 Cu St或Cu Br或Cu SSt ISO 16583-2002》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 16583-2002 en Open end blind rivets with break pull mandrel and countersunk head - Cu St or Cu Br or Cu SSt《开口型沉头抽芯盲铆钉 Cu St或Cu Br或Cu SSt ISO 16583-2002》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 16583:2002 Incorporating Corrigenda Nos. 1 and 2 Open end blind rivets with break pull mandrel and countersunk head Cu/St or Cu/Br or Cu/SSt The European Standard EN ISO 16583:2002 has the status of a British Standard ICS 21.060.40 BS EN ISO 16583:2002 This British Standar

2、d, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 November 2002 BSI 23 November 2004 ISBN 0 580 40774 8 National foreword This British Standard is the official En

3、glish language version of EN ISO 16583:2002. It is identical with ISO 16583:2002. BS EN ISO 16583:2002, together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16584:2002 and BS EN ISO 16585:2002, sup

4、ersedes BS 7349-2:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FME/6, Rivets, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Stan

5、dards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. Thi

6、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible inte

7、rnational/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN

8、ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, the Annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments

9、14312 Corrigendum No .1 24 January 2003 Replacing the EN ISO foreword page and incorporating the Annex ZA page 15326 Corrigendum No .2 23 November 2004 Addition of supersession detailsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO16583 November2002 ICS21.060.40 Englishversion Openendblindrivet

10、swithbreakpullmandrelandcountersunk headCu/StorCu/BrorCu/SSt(ISO16583:2002) Rivetsaveuglesrupturedetigecorpsouvert,tte fraiseCu/StouCu/BrouCu/SSt(ISO16583:2002) OffeneBlindnietemitSollbruchdornundSenkkopfCu/St oderCu/BroderCu/SSt(ISO16583:2002) ThisEuropeanStandardwasapprovedbyCENon14October2002. CE

11、NmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENm

12、ember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,B

13、elgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050B

14、russels 2002CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO16583:2002ECORRECTED20021218 Foreword Thisdocument(ENISO16583:2002)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandnon thr

15、eadedmechanicalfastenersandaccessories“,thesecretariatofwhichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2003,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2003. AccordingtotheCEN/CEN

16、ELECInternalRegulations,thenationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedKingdo

17、m. Endorsementnotice ThetextofISO16583:2002hasbeenapprovedbyCENasENISO16583:2002withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO16583:2002 Reference number ISO 16583:2002(E)INTERNATIONAL STANDARD ISO 16583 First edition 2002-11-01 Open end

18、 blind rivets with break pull mandrel and countersunk head Cu/St or Cu/Br or Cu/SSt Rivets aveugles rupture de tige corps ouvert, tte fraise Cu/St ou Cu/Br ou Cu/SSt ENISO16583:2002ENISO16583:2002ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of nation

19、al standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internatio

20、nal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rule

21、s given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at l

22、east 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16583 was prepared by Technical Comm

23、ittee ISO/TC 2, Fasteners. Annex A of this International Standard is for information only. ENISO16583:2002iiiINTENRATIONAL TSANDADR IS:38561 O2002(E)I SO 2002 All irthgs ersedevr 1Open end blind rivets with break pull mandrel and countersunk head Cu/St or Cu/Br or Cu/SSt 1 Scope This International S

24、tandard specifies dimensional and mechanical characteristics and application data for open end blind rivets with break pull mandrel and countersunk head, with a copper body (Cu) and either a steel (St) or a bronze (Br) or a stainless steel (SSt) mandrel and with nominal diameters from 3 mm up to and

25、 including 4,8 mm. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However

26、, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC

27、 maintain registers of currently valid International Standards. ISO 3269:2000, Fasteners Acceptance inspection ISO 14588:2000, Blind rivets Terminology and definitions ISO 14589:2000, Blind rivets Mechanical testing 3 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO

28、 14588. 3.2 Rivets dimensions See Figure 1 and Table 1. ENISO16583:20021IS:38561 O2002(E) 2 I SO 2002 All irthgs ersedevrFigure 1 Rivet dimensions Table 1 Rivet dimensions Dimensions in millimetres nom. 3 3,2 4 4,8 max. 3,08 3,28 4,08 4,88 d min. 2,85 3,05 3,85 4,65 max. 6,3 6,7 8,4 10,1 d kmin. 5,4

29、 5,8 6,9 8,3 Rivet body k max. 1,3 1,3 1,7 2 d mmax. 2 2 2,45 2,95 Mandrel p min. 25 25 25 27 Blind length b max. l max+ 3,5 l max+ 4 l max+ 4 l max+ 4,5 Rivet length l nom. = min. max. Recommended grip ranges a 5 6 1,5 to 2,0 2,0 to 2,5 6 7 2 to 3 2,5 to 3,5 8 9 2 to 3 3,5 to 5,0 2,5 to 4,0 10 11 5

30、 to 7 5 to 7 4 to 6 12 13 7 to 9 7,0 to 8,5 6 to 8 14 15 9 to 11 8,5 to 10,0 8 to 10 16 17 10,0 to 12,5 10 to 12 18 19 12 to 14 20 21 14 to 16 NOTE The rivet body dimensions are generated from the design formulae specified in annex A. aThe grip ranges of rivets with dimensions as given in Table 1, w

31、ith the material combination as given in clause 4, are specified by the minimum and maximum grip lengths. The minimum grip lengths are recommendations only. It may be possible to go into individual cases below the minimum values. ENISO16583:20022IS:38561 O2002(E) I SO 2002 All irthgs ersedevr 33.3 C

32、learance hole diameters The diameters of the clearance holes, d h1 , to accommodate the rivet in the components to be fastened are given in Table 2. Table 2 Clearance hole diameters Dimensions in millimetres d d h1nom. min. max. 3 3,1 3,2 3,2 3,3 3,4 4 4,1 4,2 4,8 4,9 5,0 Non conformance to the valu

33、es listed in Table 2 may result in assembly difficulties and/or reduction in the shear and tensile loads specified in Table 3. When necessary, to facilitate alignment, only the component on the access side may have a clearance hole larger than specified in Table 2 (see Figure 2). This may also resul

34、t in a reduction of the shear and tensile loads specified in Table 3. aEnlarged clearance hole Figure 2 Enlarged clearance hole to facilitate alignment 4 Material and finish Blind rivets in accordance with this International Standard shall have a rivet body of copper (Cu) and a mandrel made of eithe

35、r steel (St) or bronze (Br) or stainless steel (SSt) and shall have the mechanical properties as specified in clause 5. Material specification is at the descretion of the manufacturer. The surface of the rivet body shall be plain, i.e. in natural finish. ENISO16583:20023IS:38561 O2002(E) 4 I SO 2002

36、 All irthgs ersedevrThe surface finish of the steel mandrel is at the discretion of the manufacturer and may be phosphate and oil or zinc coating. The surface of bronze mandrel shall be plain, i.e. in natural finish. The surface of stainless steel mandrel shall be plain, i.e. in natural finish. 5 Me

37、chanical properties The minimum shear load, minimum tensile load and maximum mandrel break load shall be as specified in Table 3 when tested in accordance with ISO 14589. Table 3 Mechanical properties d Shear load Tensile load Mandrel break load nom. min. min. max. mm N N N 3 760 950 3 000 3,2 800 1

38、 000 3 000 4 1 500 1 800 4 500 4,8 2 000 2 500 5 000 6 Mandrel push-out resistance The load to push out the mandrel shall exceed 10 N when tested in accordance with ISO 14589. 7 Mandrel head retention capability The portion of the mandrel remaining in the set rivet shall not be ejected by the applic

39、ation of the head retention test load specified in Table 4 when tested in accordance with ISO 14589. Table 4 Mandrel head retention test loads d nom. mm Head retention test load N 3 15 3,2 15 4 20 4,8 25 ENISO16583:20024IS:38561 O2002(E) I SO 2002 All irthgs ersedevr 58 Workmanship Rivets shall be f

40、ree from burrs and harmful defects and shall have well-formed heads and shanks. After setting, rivets shall not show evidence of cracking when viewed at 5 magnification. 9 Acceptance testing If there is no other agreement, acceptance inspection in accordance with ISO 3269 applies. 10 Designation EXA

41、MPLE An open end blind rivet, with break pull mandrel and countersunk head, with nominal diameter d = 4 mm and nominal length l = 12 mm with a copper body (Cu) and a steel mandrel (St) is designated as follows: Blind rivet ISO 16583 - 4 12 - Cu/St The designation of a rivet with a bronze (Br) or sta

42、inless steel (SSt) mandrel shall follow the above example using /Br or /SSt respectively for the last element of the designation. ENISO16583:20025IS:38561 O2002(E) 6 I SO 2002 All irthgs ersedevrAnnex A (informative) Design formulae A.1 General Blind rivets in accordance with this International Stan

43、dard comply with the following design formulae and tolerances. A.2 Shank Diameter The maximum shank diameter complies with the formula: d max= d nom+ 0,08 mm The minimum shank diameter complies with the formula: d min= d nom 0,15 mm A.3 Head diameter The maximum head diameter complies with the formu

44、la: d k max= 2,1 d nomrounded to one decimal place. A.4 Head diameter tolerance The head diameter tolerance is h16 for d nomu 3,2 mm and h17 for d nom 3,2 mm A.5 Head height The maximum head height complies with the formula: k max= 0,415 d nomrounded to one decimal place. A.6 Clearance hole diameter

45、 The clearance hole diameter for blind rivet application complies with the formulae: d h1 max= d nom+ 0,2 mm d h1 min= d nom+ 0,1 mm ENISO16583:20026AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundat

46、edreference,provisionsfromother publications.Thesenormativereferencesarecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.For

47、undatedreferencesthelatesteditionofthepublicationreferredto applies(includingamendments). NOTEWhereanInternationalPublicationhasbeenmodifiedbycommonmodifications,indicated by(mod.),therelevantEN/HDapplies. Publication Year Title EN Year ISO3269 2000 FastenersAcceptanceinspection ENISO3269 2000 ISO14588 2000 BlindrivetsTerminologyand definitions ENISO14588 2000 ISO14589 2000 BlindrivetsMechanicaltesting ENISO14589 2000 ENISO16583:2002BS EN ISO 16583:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Stand