EN ISO 14922-4-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 4 Elementary Quality Requirements《热喷镀 热喷镀结构的质量要求 第4部分 基本质量要求 ISO 14922-4-1999》.pdf

《EN ISO 14922-4-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 4 Elementary Quality Requirements《热喷镀 热喷镀结构的质量要求 第4部分 基本质量要求 ISO 14922-4-1999》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 14922-4-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 4 Elementary Quality Requirements《热喷镀 热喷镀结构的质量要求 第4部分 基本质量要求 ISO 14922-4-1999》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、STD.BS1 BS EN IS0 34922-4-ENGL 3999 eii 3b24bb 07923b2 342 .I BRITISH STANDARD Thermal spraying - Quality requirements of thermally sprayed structures - Part 4: Elementary quality requirements The European Standard EN IS0 149224 1999 has the status of a British Standard ICs 25.220.20 NO COPYING WITH

2、OUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN IS0 14922-4:1999 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN IS0 L4922-4-ENGL 1999 Lh24hh9 0792363 289 I been prepared under the direction of the Sector Amd. No. Date Committee fo

3、r Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 1999 O BSI 08-1999 BS EN IS0 14922-4:1999 Comments National foreword This British Standard is the English language version of EN IS0 149224: 1999. It is identical with IS0 14922

4、4 1999. The UK participation in its preparation was entrusted to Technical Comnuttee SW40, Thermally sprayed inorganic finishes, which has the responsibjlity to: - aid enquirers to understand the text; - present to the responsible internationavEuropean committee any enquiries on the interpretation,

5、or proposals for change, and keep the UK interests informed - monitor related intemational and European developments and promulgate them in the UK A list of organizations represented on this committee can be obtained on request to its secretary. The UK voted against EN IS0 14922-4 on the grounds tha

6、t the subject of that standard is already covered by the EN IS0 9000 series on quahty management and quality assurance. However, as EN IS0 149224 achieved the requite approval from amongst the other European members of CEN, the UK is under an obligation to implement it as a British Standard. Cross-r

7、eferences Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in

8、 this document may be found in the BSI Standards Catalogue under the section entided “International Standards Correspondence Index”, or by using the “Find facfity of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Use

9、rs of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover an

10、d a back cover. The BSI copyright notice displayed throughout tkis document indicates when the document was last issued. ISBN O 580 32445 1 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN IS0 L4922-4-ENGL 1999 II 1624669 0792364 EUROPEAN STANDAR

11、D EN IS0 149224 NORMEEUROPENNE EUROPISCHE NORM June 1999 ICs 25.220 English version Thermal spraying - Quality requirements of thermally sprayed structures - Part 4: Elementary quality requirements (IS0 14922- 4: 1 999) Projection thermique - Exigences qualit des constructions obtenues par projectio

12、n thermique - Pattie 4: Exigences qualit lmentaires (IS0 14922-4:1999) Thermisches Spritzen - Qualittsanforderungen an thermisch gespritzte Bauteile - Teil 4: Elementar- Qualittsanforderungen (IS0 14922-4:1999) This European Standard was approved by CEN on 19 February 1999. CEN members are bound to

13、comply with the CEWCENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central

14、Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the

15、official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic. Denma - an application standard; - a regulatory requirement. The requirements contained within this standard may be adopted in full or may be selectively deleted by the manufacturer if not applicabl

16、e to the construction concerned. They provide a flexible framework for the control of thermal spraying in the foliowing cases: - Case 1 To provide specific requirements for thermal spraying in contracts which require the manufacturer to have a quality system other than EN IS0 9001 or EN IS0 92. - Ca

17、se 2 To provide specific requirements for thermal spraying in contracts which require the manufacturer developing a quality system. - Case 3 To provide specific requirements for themal spraying in application standards which uses thermal spraying as part of its requirements or in a contract between

18、relevant parties. 2 Normative references This European standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amend

19、ments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 473 EN 582 EN 657 Non-destructive testing - Qualification and certification o

20、f personnel Thermal spraying - Determination of the adhesive tensile strength Thermal spraying - terminology - Classification Thermal spraying - Powders - Composition - Technical supply conditions Quality systems - Model for quality assurance in desigrdevelopment, production, installation and sewici

21、ng (IS0 9001 : 1994) Quality systems - Model for quality assurance in production, installation and servicing (IS0 9002 : 1994) prEN IS0 14919 Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions Quality requirements of thermally sprayed s

22、tructures - Part 1 : Guidelines for selection and use Quality management and quality assurance - Vocabulanty EN 1274 EN IS0 9001 EN IS0 9002 EN IS0 14922-1 IS0 8402 : 1994 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 5 EN IS0 14922-41999 3 Definitions

23、 For the purposes of this standard definitions given in EN 657 and listed in part 1 of this standard apply. 4 Contract and design review 4.1 General The manufacturer shall review the contractual requirements and the design data provided by the purchaser or in- house data for construction designed by

24、 the manufacturer. This is to ensure that all information necessary to carry out the fabrication operations is available prior to the commencement of the work. The manufacturer shall affirm his capability to meet all thermal spraying contract requirements and ensure adequate planning of ail quality

25、related activities. 4.2 Application - Contract review Contractual requirements to be considered should include: a) the application standard to be used, together with any supplementary requirements; b) inspection and testing; c) final testing; d) environmental conditions relevant to thermal spraying

26、on site; e) sub-contracting, f) handling of non-conformance. 4.3 Application - Design review Design requirements to be considered should include: a) location, accessibility and sequence of all coatings; b) surface finish of the coating; c) substrate material specification and coating properties; d)

27、dimensions and details of prepared substrate surfaces and sprayed coatings; e) quality and acceptance requirements for coatings. 5 Sub-contracting Any sub-contractor shall work under the order and responsiblity of the manufacturer and shall fully comply with the relevant requirements of this standar

28、d. 6 Personnel for thermal spraying 6.1 General The manufacturer shall have at his disposal sufficient and competent personnel for the planning, performing, supervising and examining of the thermal spraying production according to specified requirements. 6.2 Qualified thermal sprayer The entire pers

29、onnel for thermal spraying must be introducedinstructed. 6.3 Thermal spraying coordinator The manufacturer shall have at his disposal personnel who controls the correct performing of the thermal spraying work. 7 Personnel for quality testing 7.1 General The manufacturer shall have at his disposal su

30、fficient and competent personnel for performing the quality testing. COPYRIGHT European Committee for StandardizationLicensed by Information Handling Services STD.BS1 ES EN IS0 L4922-4-ENGL 1799 m lib24bb 07923b9 777 Page 6 EN IS0 1492241999 7.2 Non-destructive testing The non-destnictive testing pe

31、rsonnel should be approved according to EN 473. 8 Equipment 8.1 Equipment for manufacturing The following equipment shall be available when necessary: - workshops, generally as roofed working sites; - stores for correct storage of substrate materials (to be coated components), consumables and other

32、additives for thermal spraying; - equipment for drying spray powders; - equipment and machines to prepare and machine the components for thermal spraying (e.g. degreasing equipment, sand blasting cabins); - spraying equipment, including equipment for supply, setting and control; - handling systems (

33、e.g. turntables, turning machines, robot systems); - exaust systems, dust filters, protective means against noise and radiation; - equipment for thermal treatment of the components before and after spraying; - cooling equipment; - machines, tools and equipment for post treatment of thermal sprayed c

34、oatings (e.g. grinding, turning). 8.2 Equipment necessary for health and safety and environmental protection must be available. All necessary activities to assure standards of health and safety and of emission have to be conducted. Health and safety and environmental aspects 9 Thermal spraying activ

35、ities Thermal spraying shall be performed in accordance with an appropriate spraying procedure. 10 Consumables for thermal spraying Responsibilities and procedures involved in the control of thermal spraying consumables shall be specified by the manufacturer. 11 Storage and handling of substrate mat

36、erials Storage shall be such that the material will not be adversely affected. Identification shall be maintained during storage. 12 Thermal spraying related inspection and testing 12.1 Inspection and testing before thermal spraying Before the start of thermal spraying, the following shall be checke

37、d, when necessary: - suitability and validity of the thermal sprayers certificate; - suitability of thermal spraying procedure specification; - identity of the substrate material; - identity of the consumables, e.g. according to EN 1274; - surface preparation, also shape and dimension; - fit-up, jig

38、ging and tacking; - any special requirements in thermal spraying procedure specification, e.g. prevention of distortion; - arrangement of any production test; - suitability of working conditions for thermal spraying, including environment. COPYRIGHT European Committee for StandardizationLicensed by

39、Information Handling ServicesSTD=BSI BS EN IS0 L4922-4-ENGL L999 a Lb24bb9 0792370 419 m Page 7 EN IS0 14922-4:1999 12.2 Inspection and testing after thermal spraying After thermal spraying, the compliance with relevant acceptance criteria shall be checked, when necessary. 13 Non-confomance and corr

40、ective actions Measures shall be implemented to control items which do not conform to specified requirements in order to prevent their inadvertent use. When repair and/or thermal re-spraying is undertaken by the manufacturer, appropriate prodedures shall be available at all workstations where these

41、activities are performed. When repair or thermal re- spraying is performed, the items shall be re-inspected, tested and examined in accordance with the original requirements. Measures shall also be implemented to ensure that conditions adverse to quality of the thermally sprayed construction are pro

42、mptly identified and corrected. 14 Calibration The manufacturer shall be responsible for the appropriate calibration of the inspection, measuring and testing equipment. All equipment used to assess the quality of the sprayed construction shall be suitably controlled and shall be calibrated at specif

43、ied intervals. 15 Identification and traceability Identification and traceability shall be maintained throughout the manufacturing process, where appropriate. 16 Quality records Quality records shall be retained for a minimum period of 5 years in the absence of any other specified requirements. COPY

44、RIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD.BS1 BS EN IS0 14922-4-ENGL L999 L11 Bb24bb9 0792371 355 EN standards quoted in clause 2 Page 8 Annex ZA (informative) Bib1 iography EN IS0 14922-4:1999 Table ZA.l: List of IS0 standards conforming to the EN stan

45、dards quoted in clause 2 Corresponding IS0 standards Title of the IS0 standard EN 657 EN 1274 !- I I EN 473 IS0 i4917 ) ISO/DIS 14232 Thermal spraying - Terminology, classification Thermal spraying - Powders - Composition - Technical supply conditions IEN 582 I :so 14916 l) Thermal spraying - Determ

46、ination of tensile adhesive strength ) To be published COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTILBSI BS EN IS0 L4922-4-ENGL 1999 I Lb24bb9 0792372 291 81 BS EN IS0 14922-41999 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institut

47、ion BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the intemational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should

48、 make SLUT that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee

49、 responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automaticfly receive the latest editions of standads. Buying standards Orders for all BSI, intedonal and foreign standards publications should be addressed to Customer Services. Tel 020 8996 7000. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Sta