EN ISO 14922-2-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 2 Comprehensive Quality Requirwmwnts《热喷镀 热喷镀结构的质量要求 第2部分 综合质量要求 ISO 14922-2-19.pdf

《EN ISO 14922-2-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 2 Comprehensive Quality Requirwmwnts《热喷镀 热喷镀结构的质量要求 第2部分 综合质量要求 ISO 14922-2-19.pdf》由会员分享，可在线阅读，更多相关《EN ISO 14922-2-1999 en Thermal Spraying - Quality Requirements of Thermally Sprayed Structures - Part 2 Comprehensive Quality Requirwmwnts《热喷镀 热喷镀结构的质量要求 第2部分 综合质量要求 ISO 14922-2-19.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Thermal spraying - Quality requirements of thermally sprayed structures - Part 2: Comprehensive quality re quiremen ts The European Standard EN IS0 14922-2: 1999 has the status of a British Standard ICs 25.220.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

2、 BS EN IS0 14922-2:1999 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTDmBSI BS EN IS0 14922-2-ENGL 1999 m Lb24bh9 0792335 314 D Amd.No. Date BS EN IS0 14922-2:1999 Comments National foreword This British Standard is the English language version of EN IS0

3、14922-2:1999. It is identical with IS0 14922-2: 1999. The UK participation in its preparation was entrusted to Technical Committee STV40, Thermally sprayed inorganic finishes, which has the responsibihty to: - aid enquirem to understand the text, - present to the responsible internationailEuropean c

4、ommittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. The UK

5、 voted against EN IS0 14922-2 on the grounds that the subject of that standard is already covered by the EN IS0 9000 series on quality management and quality assurance. However, as EN IS0 14922-2 achieved the requisite approval from amongst the other European members of CEN, the UK is under an oblig

6、ation to implement it as a British Standard. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards nody include an annex which lists normative references to international publications with their corresponding European publications. The British Standasds which implement inter

7、national or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by wing the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to includ

8、e all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN

9、title page, pages 2 to 11 and a back cover. The BSI copyright notice displayed throughout this document indicates when the document was iast issued. This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority

10、of the Standards Committee and comes into effect on 15 August 1999 O BSI 08-1999 ISBN O 580 32443 5 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTDmBSI BS EN IS0 14922-2-ENGL 1999 m 1624bb9 0792336 250 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM Jun

11、e 1999 ICs 25.220 English version Thermal spraying - Quality requirements of thermally sprayed structures - Part 2: Comprehensive quality requirements (IS0 14922-2:1999) Projection thermique - Exigences qualit des constructions obtenues par projection thermique - Partie 2 Exigences qualit compltes (

12、IS0 14922-2:1999) Thermisches Spritzen - Quaitsanforderungen an thermisch gespritzte Bauteile - Teil 2: Umfassende Qualittsanforderungen (IS0 14922-2: 1999) This European Standard was approved by CEN on 19 February 1999. CEN members are bound to comply with the CENICENELEC Internal Regulations which

13、 stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibiiographical references concerning such national standards may be obtained on application to the Centrai Secretariat or to any CEN member. This European Stand

14、ard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national stand

15、ards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, . Iceland, Ireland, Italy. Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE

16、 FUR NORMUNG Centrai Secretariat: rue de Stassart, 36 6-1050 Brussels 0 1999 CEN Ail rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 14922-2:1999 E COPYRIGHT European Committee for StandardizationLicensed by Information Handling Servic

17、esSTDmBSI BS EN IS0 149ZZ-Z-ENCL 1999 I 1ib24bb9 0792337 197 I Page 2 EN IS0 14922-2:1999 Contents Foreword 3 1 scope 4 Page 2 Normative references 4 3 Definitions . 5 4 Contract and design review 5 4.1 General . 5 4.2 Application - Contract review 5 4.3 Application - Design review . 6 5 Subcontract

18、ing . 6 6 Personnel for thermal spraying . 6 6.1 General . 6 6.2 Qualified thermal sprayer . 6 6.3 Thermal spraying coordinator 6 7 Personnel for quality testing . 6 7.1 General 6 7.2 Non-destructive testing 7 8.1 Equipment for manufacturing 7 8.2 Description of equipment . 7 8.3 Suitability of equi

19、pment 7 8.4 New equipment 7 8.5 Maintenance 7 8.6 Health and safety and environmental aspects 8 9 Thermal spraying activities 8 9.1 Production plan 8 9.2 Thermal spraying procedure specification . 8 9.3 Workinstructions . 8 9.4 Pre- and post-treatment 8 9.5 Documentation 8 10 Consumables for thermal

20、 spraying 8 10.1 General . 8 10.2 Batch testing 9 10.3 Storage and handling . 9 11 Storage and handling of substrate materials . 9 12 Thermal spraying related inspection and testing 9 12.1 General . 9 12.2 Inspection and testing before thermal spraying . 9 12.3 Inspection and testing during thermal

21、spraying . 9 12.4 Inspection and testing after thermal spraying . 9 12.5 Inspection and test status 101 13 Non-contormance and corrective actions . 101 15 Identification and traceability . 10 16 Qualityrecords . 10 Annex ZA (informative) Bibliography . 11 . 8 Equipment . 7 14 Calibration . 101 COPYR

22、IGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD-BSI BS EN IS0 14922-2-ENGL L777 I Lb24bb9 0772338 023 Page 3 EN IS0 14922-21999 Foreword The text of EN IS0 14922-21999 has been prepared by Technical Committee CEN/TC 240 “Thermal spraying and thermally sprayed

23、coatings“, the secretariat of which is held by DIN, in collaboration with Technical Committee ISOTTC 107 “Metallic and other inorganic coatings“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by De

24、cember 1999, and conflicting national standards shall be withdrawn at the latest by December 1999. According to the CEWCENELEC Internai Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmar

25、k, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD.BSI BS EN IS0 14722-2-ENGL L999 II 1h24bb9 0792339

26、ThT - Page 4 EN IS0 14922-21 999 1 scope This standard specifies requirements so that: - It is independent of the type of the thermally sprayed structure. - It defines quality requirements for thermal spraying both in workshops and on site. - It provides guidance for describing a manufacturers capab

27、ility to produce thermally sprayed constructions to meet specified requirements. - It may also be used as a basis for assessing the manufacturer in respect to his thermal spraying capability. This standard is appropriate when demonstration of a manufacturers capability to produce thermally sprayed c

28、onstruction, fulfilling specified quality requirements, are specified in one or more of the following: - a contract between involved parties; - an application standard: - a regulatory requirement. The requirements contained within this standard may be adopted in full or may be selectively deleted by

29、 the manufacturer if not applicable to the construction concerned. They provide a flexible framework for the control of thermal spraying in the following cases: - Case 1 To provide specific requirements for thermal spraying in contracts which require the manufacturer to have a qualtty system in acco

30、rdance with EN IS0 9001 or EN IS0 9002. - Case 2 To provide specific requirements for thermal spraying in contracts which require the manufacturer to have a quality system other than EN IS0 9001 or EN IS0 9002. - Case 3 To provide specific requirements for thermal spraying in contracts which require

31、 the manufacturer developing a quality system. - Case 4 To provide specific requirements for thermal spraying in application standards which uses thermal spraying as part of its requirements or in a contract between relevant parties. It may however be more appropriate for EN IS0 14922-3 or EN IS0 14

32、922-4 to be used in such cases. 2 Normative references This European standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, su

33、bsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 473 Non-destructive testing - Qualification and certification o

34、f personnel Thermal spraying - Determination of the tensile adhesive strength Thermal spraying - Terminology - Classification Thermal spraying - Powders - Composition - Technical supply conditions Thermal spraying - Acceptance inspection of thermal spraying equipment Thermal spraying - Thermal spray

35、 coordination - Tasks and responsibilities EN 582 EN 657 EN 1274 EN 1395 prEN 13214 COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesSTD.BSI BS EN IS0 14922-2-ENGL 1999 II I1624669 0792340 781 Page 5 EN IS0 14922-2:1999 EN IS0 9001 Quality systems - Model for

36、quality assurance in design/development, production, installation and servicing (IS0 9001 : 1984) EN IS0 9002 Quality systems - Model for quality assurance in production, installation and servicing (IS0 9002 : 1994) EN IS0 14918 Thermal spraying - Approval testing of thermal sprayers prEN IS0 1491 9

37、 Themal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions EN IS0 14922-1 Thermal spraying - Quality requirements of thermally sprayed structures - Pari 1 : Guidelines for selection and use Quality management and quality assurance - Vocabularit

38、y IS0 8402 : 1994 3 Definitions For the purposes of this standard definitions given in EN 657 and listed in part 1 of this standard apply. 4 Contract and design review 4.1 General The manufacturer shall review the contractual requirements and the design data provided by the purchaser or in- house da

39、ta for construction designed by the manufacturer. This is to ensure that all information necessary to carry out the fabrication operations is available prior to the commencement of the work. The manufacturer shall affirm his capability to meet all thermal spraying contract requirements and ensure ad

40、equate planning of all quality related activities. Contract review is carried out by the manufacturer to verify that the contract is within his capability to perform, that sufficient resources are available to achieve delivery schedules and documentation is clear and unambiguous. The manufacturer sh

41、ould ensure any variations between the contract and previous tender documentation are identified and the purchaser notified of any programme, cost or engineering changes that may result. The items in 4.2 are typically considered at or before time of the contract review. The items in 4.3 usually form

42、 pari of the design review and should be taken into account during the contract review if the design is not carried out by the manufacturer. It shall be ensured that all relevant information has been supplied by the purchaser. When a contract does not exist or items were made for stock, the manufact

43、urer is required to take into consideration the requirements of 4.2, whilst carrying out his design review (4.3). 4.2 Application - Contract review Contractual requirements to be considered should include: a) the application standard to be used, together with any supplementary requirements; b) the s

44、pecification of thermal spraying procedures, non-destructive testing procedures and heat treatment procedures; c) the approach to be used for thermal spraying procedure approval; d) the approval of personnel: e) post treatment; 1) inspection and testing; g) selection, identification andlor traceabil

45、ity, e.g. for materials, thermal sprayers and coatings (see clause 16); h) quality control arrangements, including any involvement of an independent inspection body; i) other thermal spraying requirements, e.g. batch testing of consumables; grain size, distribution and morphology and composition; j)

46、 environmental conditions relevant to thermal spraying on site; k) sub-contracting; I) handling of non-conformance. COPYRIGHT European Committee for StandardizationLicensed by Information Handling ServicesPage 6 EN IS0 14922-2: 1999 4.3 Application - Design review Design requirements to be considere

47、d should include: a) location, accessibility and sequence of all coatings; b) surface finish of the coating; c) substrate material specification and coating properties; d) dimensions and details of prepared substrate surfaces and sprayed coatings e) quality and acceptance requirements for coatings:

48、f) other special requirements, e.g. acceptability of shotpeening, heat treatment, cooling, masking. 5 Sub-contracting When a manufacturer intends to use sub-contracted services (e.g. inspection, non-destructive testing, post treatment) all relevant specifications and requirements shall be supplied b

49、y the manufacturer to the sub-contractor. The subcontractor shall provide such records and documentation of his work as may be specified by the manufacturer. Any sub-contractor shall work under the order and responsibility of the manufacturer and shall fully comply with the relevant requirements of this standard. The manufacturer has to ensure that the sub-contractor can comply with the quality requirements of the contract. The information to be provided by the manufacturer to the sub-contractor shall include all relevant data from the contract review (see 4.2) and the design revi