EN ISO 14310-2008 en Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs《石油和天然气工业 向下钻孔设备 封隔器和桥塞》.pdf

《EN ISO 14310-2008 en Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs《石油和天然气工业 向下钻孔设备 封隔器和桥塞》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 14310-2008 en Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs《石油和天然气工业 向下钻孔设备 封隔器和桥塞》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO14310:2008ICS 75.180.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPetroleum and naturalgas industries Downhole equipment Packers and bridgeplugs (ISO 14310:2008)This British Standardwas published under the authority of theStandards Policy andStrate

2、gy Committee on 3ember 2008 BSI 2008ISBN 978 0 580 58274 5Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 14310:2008National forewordThis British Standard is the UK implementation of EN ISO 14310:2008.It supersedes BS EN ISO 14310:2002 which is withdrawn.The UK participation in

3、its preparation was entrusted to TechnicalCommittee PSE/17/-/4, Drilling and production equipment for petroleumand natural gas industries.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary pr

4、ovisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.1DecEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 14310November 2008ICS 75.180.10 Supersedes EN ISO 14310:2001 English VersionPetroleum and

5、 natural gas industries - Downhole equipment -Packers and bridge plugs (ISO 14310:2008)Industries du ptrole et du gaz naturel - quipement defond de trou - Garnitures dtanchit (packers) etbouchons mcaniques disolation de fond (ISO14310:2008)Erdl- und Erdgasindustrie - Bohrloch-Untertageausrstung- Pac

6、ker und Bridge Plugs (ISO 14310:2008)This European Standard was approved by CEN on 12 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to

7、-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder t

8、he responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungar

9、y, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue

10、de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 14310:2008: EBS EN ISO 14310:2008EN ISO 14310:2008 (E) 3 Foreword This document (EN ISO 14310:2008) has been prepared by Technical Committee ISO

11、/TC 67 “Materials, equipment and offshore structures for petroleum and natural gas industries“ in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by AFNOR. This Eu

12、ropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements

13、of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 14310:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following c

14、ountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

15、Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 14310:2008 has been approved by CEN as a EN ISO 14310:2008 without any modification. BS EN ISO 14310:2008ISO 14310:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Norm

16、ative references . 1 3 Terms and definitions. 1 4 Symbols and abbreviated terms . 5 5 Functional specification. 5 5.1 General. 5 5.2 Type description . 5 5.3 Well parameters 6 5.4 Operational parameters . 6 5.5 Environmental compatibility 6 5.6 Compatibility with related well equipment. 7 5.7 Design

17、 validation 7 5.8 Quality control. 7 6 Technical specification 7 6.1 General. 7 6.2 Technical characteristics. 8 6.3 Design requirements 8 6.4 Design verification 11 6.5 Design validation requirements 11 6.6 Design changes 17 6.7 Design validation by scaling . 17 6.8 Other validations. 18 6.9 Assemb

18、ly verification. 18 7 Suppliers/manufacturers requirements18 7.1 General. 18 7.2 Documentation and data control. 18 7.3 Product identification. 20 7.4 Quality control. 20 8 Repair. 26 9 Shipment/storage 26 Bibliography . 27 BS EN ISO 14310:2008ISO 14310:2008(E) iv ISO 2008 All rights reservedForewor

19、d ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technica

20、l committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of ele

21、ctrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to th

22、e member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for ide

23、ntifying any or all such patent rights. ISO 14310 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 4, Drilling and production equipment. This second edition cancels and replaces the fi

24、rst edition (ISO 14310:2001), which has been technically revised. BS EN ISO 14310:2008ISO 14310:2008(E) ISO 2008 All rights reserved vIntroduction This International Standard has been developed by users/purchasers and suppliers/manufacturers of packers and bridge plugs and is intended for use in the

25、 petroleum and natural gas industry worldwide. This International Standard is intended to give requirements and information to both parties in the selection, manufacture, testing and use of packers and bridge plugs. Further, this International Standard addresses supplier/manufacturer requirements th

26、at set the minimum requirements with which it is necessary that suppliers/manufacturers comply to claim conformity with this International Standard. This International Standard has been structured to allow for grades of increased requirements both in quality control and design validation. These vari

27、ations allow the user/purchaser to select the grade required for a specific application. The three quality grades provide the user/purchaser with a choice of requirements to meet a specific preference or application. Quality grade Q3 is the minimum grade of quality offered by this product standard.

28、Quality grade Q2 provides additional inspection and verification steps, and quality grade Q1 is the highest grade provided. Additional quality requirements can be specified by the user/purchaser as supplemental requirements. Seven standard design-validation grades (V0 to V6) provide the user/purchas

29、er with a choice of requirements to meet a specific preference or application. Design validation grade V6 is the minimum grade and represents equipment where the validation method has been defined by the supplier/manufacturer. The complexity and severity of the validation testing increases as the gr

30、ade number decreases. It is necessary that users of this International Standard be aware that requirements above those outlined in this International Standard can be needed for individual applications. This International Standard is not intended to inhibit a supplier/manufacturer from offering, or t

31、he user/purchaser from accepting, alternative equipment or engineering solutions. This can be particularly applicable where there is innovative or developing technology. Where an alternative is offered, it is necessary that the supplier/manufacturer identify any variations from this International St

32、andard. BS EN ISO 14310:2008BS EN ISO 14310:2008INTERNATIONAL STANDARD ISO 14310:2008(E) ISO 2008 All rights reserved 1Petroleum and natural gas industries Downhole equipment Packers and bridge plugs 1 Scope This International Standard provides requirements and guidelines for packers and bridge plug

33、s as defined herein for use in the petroleum and natural gas industry. This International Standard provides requirements for the functional specification and technical specification, including design, design verification and validation, materials, documentation and data control, repair, shipment, an

34、d storage. In addition, products covered by this International Standard apply only to applications within a conduit. Installation and maintenance of these products are outside the scope of this International Standard. 2 Normative references The following referenced documents are indispensable for th

35、e application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance

36、quality limit (AQL) for lot-by-lot inspection ISO 3601-1, Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes ISO 3601-3, Fluid power systems O-rings Part 3: Quality acceptance criteria ISO 9000, Quality management systems Fundamentals and vocabular

37、y ISO 9712, Non-destructive testing Qualification and certification of personnel ISO 11960, Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells ISO 15156, (all parts), Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and

38、gas production 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 9000 and the following apply. 3.1 assembly product comprised of more than one component 3.2 bridge plug mechanical device installed in, and used for blocking fluid (liquid or gas) communi

39、cation in, the conduit and not installed in a designed receptacle BS EN ISO 14310:2008ISO 14310:2008(E) 2 ISO 2008 All rights reserved3.3 casing pipe extending from the surface and intended to line the walls of a drilled well 3.4 casing size nominal casing outside diameter (OD) as specified in ISO 1

40、1960 3.5 component individual part of an assembly 3.6 conduit casing, tubing or liner, either metallic or non-metallic 3.7 design validation process of proving a design by testing to demonstrate conformity of the product to design requirements NOTE Seven standard design validation grades (V6 to V0)

41、are specified in 6.5. ISO/TS 29001 3.8 design verification process of examining the result of a given design or development activity to determine conformity with specified requirements NOTE These activities are described in 6.4. ISO/TS 29001 3.9 drift diameter minimum inside diameter (ID) of a packe

42、r, expressed as the OD of the drift bar utilized during assembly inspection, as outlined in 7.4.11 3.10 end connection thread or other mechanism connecting the packer or bridge plug to the conduit 3.11 exposed component flow-wetted component (3.13), internally wetted component (3.18), and/or compone

43、nt contacted by well fluid below the packing element 3.12 extrusion gap radial gap between the maximum rated casing ID and the minimum OD immediately adjacent to the packing element 3.13 flow-wetted component component (3.5) that comes in direct contact with the dynamic movement of well fluids in th

44、e flow stream 3.14 gauge OD maximum specified product OD BS EN ISO 14310:2008ISO 14310:2008(E) ISO 2008 All rights reserved 33.15 grade category or rank given to different requirements for quality or design validation 3.16 heat-traceable traceable to a unique heat treatment (heat) of material 3.17 i

45、nflatable packing element packer or bridge plug packing element energized to form a seal by applying fluid pressure directly to the element 3.18 internally wetted component flow-wetted component (3.13) and any component out of the flow stream, but contacted by well fluids through a port or other pas

46、sage to the flow-wetted area 3.19 job lot batch of material or components that have undergone the same process or series of processes 3.20 job-lot traceable parts identifiable as originating from a job lot that designates the included heat(s) 3.21 liner pipe that does not extend from the surface and

47、 is intended to line the walls of a drilled well 3.22 mandrel component(s) of a packer that contain(s) the end connections and provide(s) a conduit through the packer 3.23 manufacturing process and actions performed by an equipment supplier/manufacturer that are necessary to provide finished compone

48、nt(s), assemblies and related documentation that fulfil the requests of the user/purchaser and meet the standards of the supplier/manufacturer NOTE Manufacturing begins when the supplier/manufacturer receives the order and is completed at the moment the component(s), assemblies and related documenta

49、tion are surrendered to a transportation provider. 3.24 NACE service packers or bridge plugs whose type 1 components (3.41) are manufactured from materials that comply with ISO 15156 (all parts) 3.25 non-conformance non-fulfilment of a specified requirement 3.26 packer mechanical device with a packing element (3.27), not installed in a designed receptacle, used for blocking fluid (liquid or gas) communication through the annular space between conduits by sealing off the space between them BS EN ISO 14310:2008ISO 143