EN ISO 13351-2009 en Fans - Dimensions《风扇 尺寸》.pdf

《EN ISO 13351-2009 en Fans - Dimensions《风扇 尺寸》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 13351-2009 en Fans - Dimensions《风扇 尺寸》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO13351:2009ICS 23.120NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDFans Dimensions(ISO 13351:2009)This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2010 BSI 2010ISBN 978 0 580 65054 3Amen

2、dments/corrigenda issued since publicationDate CommentsBS EN ISO 13351:2009National forewordThis British Standard is the UK implementation of EN ISO 13351:2009. It supersedes BS EN ISO 13351:2008 and BS ISO 6580:2005 which arewithdrawn.The UK participation in its preparation was entrusted to Technic

3、al Committee MCE/17, Fans.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard ca

4、nnot confer immunity from legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13351 November 2009 ICS 23.120 Supersedes EN ISO 13351:2008English Version Fans - Dimensions (ISO 13351:2009) Ventilateurs - Dimensions (ISO 13351:2009) This European Standard was approved by CEN on

5、3 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may

6、 be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CE

7、N Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan

8、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in a

9、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13351:2009: EBS EN ISO 13351:2009EN ISO 13351:2009 (E) 3 Foreword This document (EN ISO 13351:2009) has been prepared by Technical Committee ISO/TC 117 “Fans“ in collaboration with Technical Committee CEN/TC 156 “V

10、entilation for buildings” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by

11、May 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 13351:2008. According to the CEN/CENELEC Int

12、ernal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, M

13、alta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13351:2009 has been approved by CEN as a EN ISO 13351:2009 without any modification. BS EN ISO 13351:2009ISO 13351:2009(E) ISO 2009 All righ

14、ts reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Terms, definitions and symbols 1 4 Requirements 3 4.1 General. 3 4.2 Circular flanges. 4 4.3 Rectangular flanges 7 4.4 Designation of fan size. 12 Bibliography . 13 BS EN ISO 13351:2009ISO 13351:2009(E)

15、iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intere

16、sted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

17、Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the tec

18、hnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO

19、 shall not be held responsible for identifying any or all such patent rights. ISO 13351 was prepared by Technical Committee ISO/TC 117, Fans. This second edition cancels and replaces the first edition (ISO 13351:1996), of which it constitutes a minor revision. It also incorporates the content of ISO

20、 6580:2005, which will be withdrawn following its publication. BS EN ISO 13351:2009ISO 13351:2009(E) ISO 2009 All rights reserved vIntroduction This International Standard gives dimensional details of circular and rectangular flanges of fans in addition to specifying the fan size designation. For ci

21、rcular flanges, the values specified in ISO 6580 have been retained for light-duty fans, in parallel with those values given in Tables 3 and 4 for medium- and heavy-duty fans. While it does not constrain the manufacturers choice of flange details, this International Standard facilitates interchangea

22、bility, thereby helping to reduce technical barriers to trade. Throughout this International Standard, the principal dimensions are based on the rounded values of preferred numbers given in ISO 497. BS EN ISO 13351:2009BS EN ISO 13351:2009INTERNATIONAL STANDARD ISO 13351:2009(E) ISO 2009 All rights

23、reserved 1Fans Dimensions 1 Scope This International Standard specifies the dimensions of the circular and rectangular flanges of general-purpose fans, as well as the fan size designations. It is not applicable to cross-flow fans or to fan appliances used for individual household or similar applicat

24、ions. For circular flanges, it provides for three different flange series: one for light-duty casing thicknesses, another for medium-duty fans and the third for heavy-duty fans as used on sea-going vessels or in heavy industry. In order not to restrict fan design unduly, only the pitch diameter, hol

25、e numbers and hole diameters are specified. Flange thickness, as well as internal and external flange diameters, may be chosen freely within the limits of good engineering practice. 2 Normative references The following referenced documents are indispensable for the application of this document. For

26、dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers ISO 13349, Industrial fans Vocabulary and definitions of categories 3 Terms, definitions an

27、d symbols For the purposes of this document, the terms and definitions given in ISO 13349 and the following terms, definitions and symbols apply. 3.1 light-duty fan fan suitable for air that is non-toxic, not saturated, non-corrosive, non-flammable, free from abrasive particles, and not exceeding a

28、temperature of 80 C, or 40 C if the motor or the fan bearings are in the air stream, and for pressures up to 2 kPa NOTE See Table 1. 3.2 medium-duty fan fan with flange dimensions as specified in Figure 4 and Table 2 and suitable for pressures up to 10 kPa 3.3 heavy-duty fan fan with larger flange d

29、imensions as specified in Figure 4 and Table 3 and suitable for pressures up to 40 kPa BS EN ISO 13351:2009ISO 13351:2009(E) 2 ISO 2009 All rights reserved3.4 nominal impeller tip diameter D diameter of the impeller tip on which the design of the fan is based NOTE See Figures 1 to 3. D nominal impel

30、ler tip diameter, in millimetres (see Figures 1 to 3) DRactual impeller tip diameter, in millimetres (see Figures 1 to 3) d1pitch circle diameter, in millimetres d2hole diameter, in millimetres d3bolt diameter, in millimetres d4washer diameter, in millimetres e casing thickness, in millimetres g hol

31、e offset, in millimetres l arc length between bolt holes, in millimetres N number of holes P pitch angle between bolt holes, in degrees Figure 1 Impeller Centrifugal fan BS EN ISO 13351:2009ISO 13351:2009(E) ISO 2009 All rights reserved 3Figure 2 Impeller Axial-flow fan aUsually, D = DRFigure 3 Impe

32、ller Mixed-flow fan 4 Requirements 4.1 General This International Standard adopts the Renard R 20 series according to ISO 497 as the nominal dimensions for impeller tip diameters, the inside diameters of circular flanges and the inside lengths of the sides of rectangular flanges. It takes into accou

33、nt the maximum casing thicknesses likely to be used for general-purpose fans, as well as typical manufacturing tolerances representative of engineering “good practice”. The smallest practical pitch circle diameter can be related to the inside diameter of the casing, the casing thickness, the size of

34、 the weld fillet or bend radius at the junction of the flange and the casing, and the normal washer diameter. Light-duty circular flanges might not be suitable for the use of open-ended spanners in all cases. BS EN ISO 13351:2009ISO 13351:2009(E) 4 ISO 2009 All rights reservedThis International Stan

35、dard accepts that the number and diameter of bolts or screws cannot be established on a theoretical basis. Practical experience of satisfactory service, optimum cost of installation and manufacture, as well as dimensional tolerances of production are the most important considerations. The dimensions

36、 of circular and rectangular flanges are given in sizes corresponding to nominal diameters from 100 mm to 2 000 mm. In the smaller sizes (below about 200 mm) flange details may be determined by the customers specification. However, where this is not the case, then the specifications of this Internat

37、ional Standard are to be applied. 4.2 Circular flanges The number of flange holes is divisible by four to permit the orientation of cylindrical cased fans at positions of 90. The holes are disposed equally on each side of the centrelines of the fan. This permits a flange to be divided in half if a s

38、plit casing is required. It also allows better access to the fixings on the remote side of a fan in a confined installation. When an intermediate fan size is required, the R 40 series in accordance with ISO 3 shall be used to obtain the nominal inside diameter. The flange details shall be interprete

39、d from the next larger R 20 size. In exceptional circumstances, when even smaller increments of fan size are required, it is recommended that the R 80 series be used. See Figure 4. Figure 4 Dimensions Circular flanges BS EN ISO 13351:2009ISO 13351:2009(E) ISO 2009 All rights reserved 5Table 1 Dimens

40、ions Circular flanges Light-duty fans Dimensions in millimetres d0d1102ddN d2d3d4emax.100 120 10 4 90 7 M6 12,5 1,6 112 137 12,5 4 90 7 M6 12,5 2 125 150 12,5 4 90 7 M6 12,5 2 140 165 12,5 4 90 7 M6 12,5 2 160 185 12,5 4 90 7 M6 12,5 2 180 205 12,5 4 90 7 M6 12,5 2 200 225 12,5 4 90 7 M6 12,5 2 224

41、254 15 4 90 7 M6 12,5 2 250 280 15 4 90 10 M8 17 2,5 280 320 20 4 90 10 M8 17 2,5 315 355 20 8 45 10 M8 17 3 355 395 20 8 45 10 M8 17 3 400 450 25 8 45 12 M10 21 3 450 500 25 8 45 12 M10 21 3 500 560 30 12 30 12 M10 21 3,5 560 620 30 12 30 12 M10 21 3,5 630 690 30 12 30 12 M10 21 5 710 770 30 16 22,

42、5 12 M10 21 5 800 860 30 16 22,5 12 M10 21 5 900 970 35 16 22,5 15 M12 24 6 1 000 1 070 35 16 22,5 15 M12 24 6 1 120 1 190 35 20 18 15 M12 24 6 1 250 1 320 35 20 18 15 M12 24 6 1 400 1 470 35 20 18 15 M12 24 6 1 600 1 680 40 24 15 19 M16 30 8 1 800 1 880 40 24 15 19 M16 30 8 2 000 2 080 40 24 15 19

43、M16 30 8 BS EN ISO 13351:2009ISO 13351:2009(E) 6 ISO 2009 All rights reservedTable 2 Dimensions Circular flanges Medium-duty fans Dimensions in millimetres D d112dDN l d2d3d4aea100 139 19,5 4 90 109 9,5 M8 17 1,5 u e u 6112 151 19,5 4 90 119 9,5 M8 17 1,5 u e u 6125 165 20 4 90 130 9,5 M8 17 1,5 u e

44、 u 6140 182 21 8 45 71 11,5 M10 21 1,5 u e u 6160 200 20 8 45 79 11,5 M10 21 1,5 u e u 6180 219 19,5 8 45 86 11,5 M10 21 1,5 u e u 6200 241 20,5 8 45 95 11,5 M10 21 1,5 u e u 6224 265 20,5 8 45 104 11,5 M10 21 1,5 u e u 6250 292 21 8 45 115 11,5 M10 21 1,5 u e u 6280 332 26 8 45 130 11,5 M10 21 1,5

45、u e u 6315 366 25,5 8 45 144 11,5 M10 21 1,5 u e u 6355 405 25 8 45 159 11,5 M10 21 1,5 u e u 6400 448 24 12 30 117 11,5 M10 21 1,5 u e u 6450 497 23,5 12 30 130 11,5 M10 21 1,5 u e u 6500 551 25,5 12 30 144 11,5 M10 21 1,5 u e u 6560 629 34,5 16 22,5 124 14 M12 24 2 u e u 6 630 698 34 16 22,5 137 1

46、4 M12 24 2 u e u 6 710 775 32,5 16 22,5 152 14 M12 24 2,5 u e u 6800 869 34,5 24 15 113 14 M12 24 2,5 u e u 6900 958 29 24 15 125 14 M12 24 3 u e u 6 1 000 1 067 33,5 24 15 140 14 M12 24 3 u e u 6 1 120 1 200 40 32 11,25 118 18 M16 30 4 u e u 6 1 250 1 337 43,5 32 11,25 131 18 M16 30 4 u e u 6 1 400

47、 1 475 37,5 32 11,25 145 18 M16 30 5 u e u 6 1 600 1 675 37,5 40 9 132 18 M16 30 5 u e u 6 1 800 1 875 37,5 40 9 147 18 M16 30 6 2 000 2 073 36,5 40 9 163 18 M16 30 6 aGiven for information. BS EN ISO 13351:2009ISO 13351:2009(E) ISO 2009 All rights reserved 7Table 3 Dimensions Circular flanges Heavy

48、-duty fans Dimensions in millimetres D d112dDN l d2d3d4 aea250 325 37,5 12 30 85 14,5 M12 24 280 355 37,5 12 30 93 14,5 M12 24 315 390 37,5 12 30 102 14,5 M12 24 355 430 37,5 16 22,5 84 14,5 M12 24 400 475 37,5 16 22,5 93 14,5 M12 24 450 525 37,5 20 18 82 14,5 M12 24 500 575 37,5 20 18 90 14,5 M12 2

49、4 560 650 45 20 18 102 18,5 M16 30 630 720 45 20 18 113 18,5 M16 30 710 800 45 20 18 126 18,5 M16 30 800 890 45 24 15 116 18,5 M16 30 900 990 45 24 15 130 18,5 M16 30 1 000 1 090 55 28 12,85 122 18,5 M16 30 1 120 1 230 55 28 12,85 138 24 M20 37 1 250 1 360 55 28 12,85 153 24 M20 37 1 400 1 510 55 32 11,25 148 24 M20 37 1 600 1 710 55 36 10 149 24 M20 37 1 800 1 910 55 40 9 150 24 M20 37 8 u e u 10aGiven for information. 4.3 Rectangular flanges The objective of the system is to provide t