EN ISO 11148-6-2012 en Hand-held non-electric power tools - Safety requirements - Part 6 Assembly power tools for threaded fasteners《手持非电动工具 安全要求 第6部分 螺纹紧固件装配电动工具》.pdf

《EN ISO 11148-6-2012 en Hand-held non-electric power tools - Safety requirements - Part 6 Assembly power tools for threaded fasteners《手持非电动工具 安全要求 第6部分 螺纹紧固件装配电动工具》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 11148-6-2012 en Hand-held non-electric power tools - Safety requirements - Part 6 Assembly power tools for threaded fasteners《手持非电动工具 安全要求 第6部分 螺纹紧固件装配电动工具》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 11148-6:2012Hand-held non-electric power tools Safety requirementsPart 6: Assembly power tools for threaded fastenersBS EN ISO 11148-6:2012 BRITISH STANDARDNational for

2、ewordThis British Standard is the UK implementation of EN ISO 11148-6:2012. It supersedes BS EN ISO 11148-6:2010 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee MCE/8/-/2, Hand-held, non-electric power tools - Safety.A list of organizations represented

3、 on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 785

4、67 2 ICS 25.140.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDA

5、RD NORME EUROPENNE EUROPISCHE NORM EN ISO 11148-6 December 2012 ICS 25.140.10 Supersedes EN ISO 11148-6:2010English Version Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2012) Machines portatives moteur non lectrique - Exi

6、gences de scurit - Partie 6: Machines dassemblage pour lments de fixation filets (ISO 11148-6:2012) Handgehaltene nicht elektrisch betriebene Maschinen - Sicherheitsanforderungen - Teil 6: Maschinen fr Schraubverbindungen (ISO 11148-6:2012) This European Standard was approved by CEN on 17 December 2

7、012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained

8、 on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CE

9、NELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, It

10、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix

11、17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 11148-6:2012: EBS EN ISO 11148-6:2012EN ISO 11148-6:2012 (E) 3 Foreword This document (EN ISO 11148-6:2012) has been prepared by Technical Committee ISO/T

12、C 118“Compressors and pneumatic tools, machines and equipment“ in collaboration with Technical CommitteeCEN/TC 255 “Hand-held, non-electric power tools - Safety” the secretariat of which is held by SIS. This European Standard shall be given the status of a national standard, either by publication of

13、 an identicaltext or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn atthe latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. CEN and/or CENELEC shall not be held

14、responsible for identifying any or all such patent rights. This document supersedes EN ISO 11148-6:2010. This document has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EU Directive(s). For relatio

15、nship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cypr

16、us, CzechRepublic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Ki

17、ngdom. Endorsement notice The text of ISO 11148-6:2012 has been approved by CEN as a EN ISO 11148-6:2012 without anymodification. BS EN ISO 11148-6:2012EN ISO 11148-6:2012 (E) 4 Annex ZA (informative) Relationship between this European Standard and the EssentialRequirements of EU Directive 2006/42/E

18、C This European Standard has been prepared under a mandate given to CEN by the European Commissionand the European Free Trade Association to provide a means of conforming to Essential Requirements of theNew Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journ

19、al of the European Union under that Directive and has beenimplemented as a national standard in at least one Member State, compliance with the clauses of thisstandard confers, within the limits of the scope of this standard, a presumption of conformity with thecorresponding Essential Requirements of

20、 that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) fallingwithin the scope of this standard. BS EN ISO 11148-6:2012ISO 11148-6:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12

21、 Normative references . 13 Terms and definitions . 23.1 General definitions 23.2 Definitions related to assembly power tools for threaded fasteners 44 Safety requirements and/or protective measures 54.1 General . 54.2 Mechanical safety 54.3 Thermal safety 64.4 Noise reduction 64.5 Vibration . 64.6 M

22、aterials and substances processed, used or exhausted . 74.7 Ergonomics . 74.8 Controls . 95 Verification 105.1 General conditions for tests .105.2 Noise .105.3 Vibration .105.4 Unintentional start .105.5 Power tool construction 105.6 Structure of verification of safety requirements . 116 Information

23、 for use . 116.1 Marking, signs and written warnings . 116.2 Instructions handbook .126.3 Operating instructions .176.4 Data .176.5 Maintenance instructions 18Annex A (informative) List of significant hazards 19Annex B (informative) Examples of assembly power tools for threaded fasteners covered by

24、this part of ISO 11148 .21Annex C (normative) Symbols for labels and signs23Annex D (normative) Additional safety requirements related to internal combustion engine power tools .25Bibliography .29BS EN ISO 11148-6:2012ISO 11148-6:2012(E)ForewordISO (the International Organization for Standardization

25、) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repr

26、esented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are

27、 drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International

28、 Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 11148-6 was prepa

29、red by Technical Committee ISO/TC 118, Compressors and pneumatic tools, machines and equipment, Subcommittee SC 3, Pneumatic tools and machines.This second edition cancels and replaces the first edition (ISO 11148-6:2010), of which it constitutes a minor revision.ISO 11148 consists of the following

30、parts, under the general title Hand-held non-electric power tools Safety requirements: Part 1: Assembly power tools for non-threaded mechanical fasteners Part 2: Cutting-off and crimping power tools Part 3: Drills and tappers Part 4: Non-rotary percussive power tools Part 5: Rotary percussive drills

31、 Part 6: Assembly power tools for threaded fasteners Part 7: Grinders Part 8: Sanders and polishers Part 9: Die grinders Part 10: Compression power tools Part 11: Nibblers and shears Part 12: Circular, oscillating and reciprocating sawsA part 13, dealing with fastener driving tools, is under prepara

32、tion.iv ISO 2012 All rights reservedBS EN ISO 11148-6:2012ISO 11148-6:2012(E)IntroductionThis document is a type C standard as stated in ISO 12100.The machinery concerned and the extent to which hazards, hazardous situations and events are covered are defined in the Scope of this part of ISO 11148.W

33、hen provisions of this type C standard are different from those that are stated in type A or B standards, the requirements of this type C standard take precedence over the requirements of other standards for machines that have been designed and built according to the requirements of this type C stan

34、dard.ISO 11148 consists of a number of independent parts for individual types of hand-held, non-electric power tools.Certain elements of this part of ISO 11148 cover hand-held, non-electric power tools driven by internal combustion engines powered by gaseous or liquid fuel. In these parts, the safet

35、y aspects relating to internal combustion engines are found in a normative annex.The parts are type C standards and refer to pertinent standards of types A and B where such standards are applicable. ISO 2012 All rights reserved vBS EN ISO 11148-6:2012BS EN ISO 11148-6:2012Hand-held non-electric powe

36、r tools Safety requirements Part 6: Assembly power tools for threaded fastenersIMPORTANT The electronic file of this document contains colours that are considered useful for the correct understanding of the document. Users should consider printing this document using a colour printer. ISO 3864-4 pro

37、vides colourimetric and photometric properties together with, as a guideline, references from colour order systems.1 ScopeThis part of ISO 11148 applies to hand-held non-electric power tools (hereinafter “assembly power tools for threaded fasteners”) intended for tightening or installing of threaded

38、 fasteners. The assembly power tools for threaded fasteners can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for use by one operator and supported by the operators hand or hands, with or without a suspension, e.g. a balancer.This part of ISO 11148 cov

39、ers air-hydraulic impulse wrenches; impact wrenches; fastener installation tools; nutrunners; open-ended spanners (crow-foot with open-ended socket or tube nut wrench); ratchet wrenches; screwdrivers.NOTE 1 For examples of assembly power tools for threaded fasteners, see Annex B.This part of ISO 111

40、48 does not cover special requirements and modifications of assembly power tools for threaded fasteners for the purpose of mounting them in fixtures.This part of ISO 11148 deals with all significant hazards, hazardous situations or hazardous events when the tools are used as intended and under condi

41、tions of misuse which are reasonably foreseeable by the manufacturer, with the exception of the use of assembly power tools for threaded fasteners in potentially explosive atmospheres.NOTE 2 EN 13463-1 gives requirements for non-electrical equipment for potentially explosive atmospheres.2 Normative

42、referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 3857-3, Compressors, pneumatic tools

43、 and machines Vocabulary Part 3: Pneumatic tools and machinesISO 3864-2, Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labelsINTERNATIONAL STANDARD ISO 11148-6:2012(E) ISO 2012 All rights reserved 1BS EN ISO 11148-6:2012ISO 11148-6:2012(E)ISO 5391, Pn

44、eumatic tools and machines VocabularyISO 7000, Graphical symbols for use on equipment Registered symbols1)ISO 7010, Graphical symbols Safety colours and safety signs Registered safety signs1)ISO 9158, Road vehicles Nozzle spouts for unleaded gasolineISO 9159, Road vehicles Nozzle spouts for leaded g

45、asoline and diesel fuelISO 12100:2010, Safety of machinery General principles for design Risk assessment and risk reductionISO 13732-1, Ergonomics of the thermal environment Methods for the assessment of human responses to contact with surfaces Part 1: Hot surfacesISO 13732-3, Ergonomics of the ther

46、mal environment Methods for the assessment of human responses to contact with surfaces Part 3: Cold surfacesISO 15744, Hand-held non-electric power tools Noise measurement code Engineering method (grade 2)ISO 17066, Hydraulic tools VocabularyISO 20643, Mechanical vibration Hand-held and hand-guided

47、machinery Principles for evaluation of vibration emissionISO 28927-2, Hand-held portable power tools Test methods for evaluation of vibration emission Part 2: Wrenches, nutrunners and screwdriversEN 12096, Mechanical vibration Declaration and verification of vibration emission values3 Terms and defi

48、nitionsFor the purposes of this document, the terms and definitions given in ISO 3857-3, ISO 5391, ISO 12100 and ISO 17066 (for hydraulic tools), and the following apply.3.1 General definitions3.1.1hand-held power toolmachine operated by one or two hands and driven by rotary or linear motors powered

49、 by compressed air, hydraulic fluid, gaseous or liquid fuel, electricity or stored energy (e.g. by a spring) to do mechanical work and so designed that the motor and the mechanism form an assembly that can easily be brought to its place of operationNOTE Hand-held power tools driven by compressed air or gas are called pneumatic tools (or air tools). Hand-held power tools driven by hydraulic liquid are called hydraulic tools.3.1.2inserted tooltool inserted in the assembly power tool