EN 61988-1-2011 en Plasma display panels - Part 1 Terminology and letter symbols《等离子体显示板 第1部分 术语和字母符号》.pdf

《EN 61988-1-2011 en Plasma display panels - Part 1 Terminology and letter symbols《等离子体显示板 第1部分 术语和字母符号》.pdf》由会员分享，可在线阅读，更多相关《EN 61988-1-2011 en Plasma display panels - Part 1 Terminology and letter symbols《等离子体显示板 第1部分 术语和字母符号》.pdf（58页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 61988-1:2011Plasma display panels Part 1: Terminology and letter symbolsBS EN 61988-1:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation o

2、f EN 61988-1:2011. It is identical to IEC 61988-1:2011. It supersedes BS EN 61988-1:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/47, Semiconductors.A list of organizations represented on this committee can be obtained on request to its secre

3、tary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011ISBN 978 0 580 65878 5ICS 31.260Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published

4、 under the authority of theStandards Policy and Strategy Committee on 31 October 2011.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 61988-1:2011EUROPEAN STANDARD EN 61988-1 NORME EUROPENNE EUROPISCHE NORM September 2011 CENELEC European Committee for Electrotechnical Standardi

5、zation Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61988-1:2011 E ICS

6、 31.260 Supersedes EN 61988-1:2003English version Plasma display panels - Part 1: Terminology and letter symbols (IEC 61988-1:2011) Panneaux daffichage plasma - Partie 1: Terminologie et symboles littraux (CEI 61988-1:2011) Plasmabildschirme - Teil 1: Terminologie und Buchstabensymbole (IEC 61988-1:

7、2011) This European Standard was approved by CENELEC on 2011-08-30. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliograp

8、hical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

9、a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Gr

10、eece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 61988-1:2011EN 61988-1:2011 - 2 - Foreword The text of document 110/236/CDV, future edition 2

11、 of IEC 61988-1, prepared by IEC/TC 110, Flat panel display devices, was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61988-1:2011. This document supersedes EN 61988-1:2003. EN 61988-1:2011 includes the following significant technical changes with respect to EN 61988-1:20

12、03: Additional terms were added in Clause 3. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2012-05-30 latest date by which the national standards conflicting with the d

13、ocument have to be withdrawn (dow) 2014-08-30 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. _ Endorsement notice The text of the Int

14、ernational Standard IEC 61988-1:2011 was approved by CENELEC as a European Standard without any modification. _ BS EN 61988-1:2011- 3 - EN 61988-1:2011 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced docu

15、ments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modificatio

16、ns, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61988-2-1 201X1)Plasma display panels - Part 2-1: Measuring methods - Optical and optoelectrical EN 61988-2-1 201X1)1)At draft stage. 2 61988-1 IEC:2011 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references

17、. 5 3 Terms and definitions . 5 4 Symbols . 31 4.1 General . 31 4.2 Symbol list by term name 31 4.3 Symbol list by symbol 33 Annex A (informative) Description of the technology 35 Annex B (informative) Relationship between voltage terms and discharge characteristics 46 Annex C (informative) Gaps . 4

18、7 Annex D (informative) Manufacturing . 48 Annex E (informative) Interconnect pad . 51 Bibliography 52 Figure A.1 Principal structures and discharge characteristics of a DC PDP cell and an AC PDP cell . 35 Figure A.2 Discharge characteristics of a cell (single cell static characteristics) 37 Figure

19、A.3 Static characteristics of cells in a panel or a group of cells . 38 Figure A.4 Write waveform components . 39 Figure A.5 Operation of a two-electrode type AC PDP . 40 Figure A.6 Relation between margins and applied voltages 41 Figure A.7 Structure of a three-electrode type, surface discharge col

20、our AC PDP 42 Figure A.8 Address-, display-period separation method . 43 Figure A.9 A driving waveform for ADS method applied to a three-electrode 44 Figure A.10 Address while display method . 45 Figure C.1 Gaps (sustain gap, plate gap and interpixel gap) in a three-electrode type AC PDP 47 Figure D

21、.1 PDP manufacturing flow chart . 49 Figure E.1 Interconnect pad group . 51 Figure E.2 Dimensions of interconnect pads 51 Table B.1 Relation between static, dynamic and operating discharge characteristics in a cell, a panel or a group of cells 46 61988-1 IEC:2011 3 INTERNATIONAL ELECTROTECHNICAL COM

22、MISSION _ PLASMA DISPLAY PANELS Part 1: Terminology and letter symbols FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote intern

23、ational co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter

24、 referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participa

25、te in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an int

26、ernational consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reas

27、onable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IE

28、C Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of confo

29、rmity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publicat

30、ion. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or

31、for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct

32、 application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61988-1 has been prepared by I

33、EC technical committee 110: Flat panel display devices. This second edition cancels and replaces the first edition published in 2003, and constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: Additional terms were added in Clause 3. The text

34、 of this standard is based on the following documents: CDV Report on voting 110/236/CDV 110/286/RVC Full information on the voting for the approval on this standard can be found in the report on voting indicated in the above table. 4 61988-1 IEC:2011 This publication has been drafted in accordance w

35、ith the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 61988 series, under the general title Plasma display panels, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web

36、 site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61988-1 IEC:2011 5 PLASMA DISPLAY PANELS Part 1: Terminology and letter symbols 1 Scope This part of IEC 61988

37、 gives the preferred terms, their definitions and symbols for colour AC plasma display panels (AC PDP); with the object of using the same terminology when publications are prepared in different countries. Guidance on the technology is provided in the annexes. 2 Normative references The following ref

38、erenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61988-2-1:, Plasma display panels Part 2-1: Measuring methods

39、Optical and optoelectrical13 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 AC PDP NOTE See AC plasma display panel. 3.2 AC plasma display panel AC PDP plasma display panel in which the gas discharge region is insulated from the electrodes tha

40、t are driven with AC voltage pulses 3.3 address bias Vba data bias common voltage applied to all address electrodes during addressing 3.4 address cycle period time interval between initiation of the closest spaced successive address pulses 3.5 address discharge discharge that changes the state of a

41、PDP subpixel 1Second edition, to be published. 6 61988-1 IEC:2011 3.6 address electrode data electrode electrode, orthogonal to the scan electrode, that is used in driving the subpixels with the image data 3.7 address period time interval including the reset step and the address step 3.8 address pul

42、se data pulse incremental voltage pulse applied to a single address (data) electrode for addressing, to select a subpixel according to an image to be displayed NOTE See scan pulse. 3.9 address step time interval needed to address all pixels in the panel in a given subfield as applied to the ADS meth

43、od 3.10 address voltage Va data voltage amplitude of the voltage pulses applied to the address (data) electrode during addressing (excludes the address bias on the electrode) 3.11 address while display method AWD method grey scale drive technique that addresses only a portion of the pixels of the pa

44、nel in any time within a sustain period NOTE See also ADS. 3.12 addressability number of pixels in the horizontal and vertical directions, that can have their luminance changed NOTE Usually expressed as the number of horizontal pixels by the number of vertical pixels. This term is not synonymous wit

45、h resolution. See resolution. 3.13 addressing setting or changing the state of a subpixel with an address pulse 3.14 ADS method address, display-period separation method grey scale drive technique that consists of addressing all the pixels in the panel in one time period and sustaining all the pixel

46、s in the panel in a separate time period 3.15 ageing manufacturing process consisting of operating the panel under conditions that stabilize its performance 61988-1 IEC:2011 7 3.16 annealing process of heating the glass above its annealing point and cooling at a controlled rate to minimize dimension

47、al changes during subsequent high temperature cycles 3.17 anode positively charged surface of a device that collects electrons from the discharge NOTE In an AC PDP, the cathode and anode exchange their roles on alternate half-cycles. 3.18 APL average picture level time average of a video signal duri

48、ng the active scanning time integrated over a frame period, which is expressed as a percentage of the full white signal level while designating 0 % as the black signal level NOTE There are two types of APL. See pre-gamma APL and post-gamma APL. 3.19 aspect ratio ratio of screen width to screen heigh

49、t 3.20 auto power control APC circuit means to control the peak and/or average power of the display 3.21 auxiliary anode anode in a DC PDP whose discharge contributes to supply priming particles to ignite a discharge in a cell 3.22 back plate rear plate plate furthest from the viewer 3.23 back-filling NOTE See filling. 3.24 bake NOTE See bakeout and baking. 3.25 bakeout high temperature processing of a vacuum system and/or PDP to assist in achieving