EN 61313-1-1997 en Fibre Optic Passive Components and Cable Assemblies Part 1 Capability Approval - Generic Specification《光纤无源器件和电缆组件 第1部分 容量鉴定 通用规范 IEC 1313-1-1995》.pdf

《EN 61313-1-1997 en Fibre Optic Passive Components and Cable Assemblies Part 1 Capability Approval - Generic Specification《光纤无源器件和电缆组件 第1部分 容量鉴定 通用规范 IEC 1313-1-1995》.pdf》由会员分享，可在线阅读，更多相关《EN 61313-1-1997 en Fibre Optic Passive Components and Cable Assemblies Part 1 Capability Approval - Generic Specification《光纤无源器件和电缆组件 第1部分 容量鉴定 通用规范 IEC 1313-1-1995》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、. - STD.BS.1 BS EN bL3L3-L-ENGL 1797 I Lb24bb7 Ob4b225 7T3 I BRITISH STANDARD Fibre optic passive components and cable assemblies Part 1. Capability approval - Generic specification The European Standard EN 61313-1 : 1997 has the status of a British Standasd ICs 33.180.20 NO COPYING WITHOUT BSI PERM

2、ISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 61313-1 : 1997 IEC 61313-1 : 1995 BS EN 61313-1 : 1997 National foreword This British Standard is the English language version of EN 61313-1 : 1997. It is identical with IEC 61313-1 : 1995. The UK participation in its preparation was entrusted by Tec

3、hnical Committee EPL/86, Fibre optics, to Subcommittee EPL/86/2, Interconnecting devices and passive components, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible intemdionaYEuropean committee any enquiries on the interpretation, or proposals for c

4、hange, and keep the UK interests informed; - monitor related internationai and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, ali IEC publications have the number 60000 ad

5、ded to the old number, For instance, IEC 27-1 has been renumbered as lEC 60027-1. For a period of the during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that annex ZA lists normative r

6、eferences to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or using the

7、 Find faciiity of the BSI Stanbds Electronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover

8、. This British Standard, having been prepared under the direction of the Elecmtechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 16 August 1997 Amendments issued since publication O BSI 1997 ISBN O 580 27801 8 STD-BSI BS EN b1313-L-ENGL 1797 Lb2

9、4bb7 0b4b227 57b = EUROPEAN STANDARD NORME EUROPEENNE EUROPISCHE NORM EN 61313-1 May 1997 ICs 33.1 80.20 Descriptors: Capability approval of optic passive components English version Fibre optic passive components and cable assemblies Part 1 : Capability approval - Generic specification (IEC 131 3-1

10、:1995) Ensembles de cables et composants passifs fibres optiques Partie 1 : Agrment de savoir-faire Spcification gnrique Fachgrundspezifikation Passive LWL-Bauelemente und konfektionierte LWL-Kabel Teil 1 : Befhigungsanerkennung (CE1 131 3-1 : 1995) (IEC 1313-1:1995) * * m This European Standard was

11、 approved by CENELEC on 1997-03-1 1. CENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning suc

12、h national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own l

13、anguage and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden

14、, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europiisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels - - 1997 CENELEC - All rights of exploitation

15、 in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61313-1:1997 E Page 2 EN 61313-1 : 1997 Foreword The text of the international Standard IEC 131 3-1 : 1995, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, wa

16、s submitted to the formal vote and was approved by CENELEC as EN 61 31 3-1 on 1997-03-1 1 without any modification. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dpl 1 998-03-0

17、 1 - latest date by which the national standards conflicting (daw) 1998-03-01 with the EN have to be withdrawn Annexes designated “normative“ are part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the Internat

18、ional Standard IEC 1313-1:1995 was approved by CENELEC as a European Standard without any modification. . * m * CONTENTS clause Page 3 EN 61313-1 : 1997 1 General . 1.1 Scope . 1.2 Normative references . 1.3 Abbreviations . 2 Requirements . 2.1 Capability approval . 2.2 Classification . 2.3 Document

19、ation 2.4 Design and construction 2.5 Quality assessment 2.6 Identification and marking 3 Quality assessment procedures 3.1 Primary stage of manufacture . 3.2 Capability approval procedures 3.3 Quality conformance inspection 3.4 Certified records of released lots 3.5 Delayed deliveries 3.6 Release b

20、efore completion of group B tests . 3.7 Measurements and test procedures . 3.8 Unchecked parameters Annex ZA (normative) Normative references to international publications Page 4 4 4 5 5 5 5 5 7 7 7 8 8 8 io 11 11 11 11 11 with their corresponding European publications 12 Page 4 EN 61313-1 : 1997 FI

21、BRE OPTIC PASSIVE COMPONENTS AND CABLE ASSEMBLIES - Part 1 : Capability approval - Generic specification 1 General 1.1 Scope This specification applies to fibre optic passive components and cable assemblies for delivery under the capability approval procedure. It includes: - component and cable asse

22、mbly requirements; - quality assessment procedures. 1.2 Normative references The following normative documents contain provisions which, throu$h reference in this text, constitute provisions of this specification. At the time of publication, the editions indicated were valid. All standards are subje

23、ct to revision and parties to agreements based on this specification are encouraged to apply the most recent editions of the norma- tive documents indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 68, Environmental testing IEC 68-1 : 1988, Env

24、ironmental testing - Part 7: General and guide IEC 41 O: 1973. Sampling plans and procedures for inspection by attributes IEC 695-2-2: 1991 , Fire hazard testing - Part 2: Test methods - Section 2: Needle-flame test IEC 1300: 1995, Basic measurement and test procedures for passive fibre optic compo-

25、 nents IEC QC 001001: 1986. Basic rules of the IEC Quality Assessment System for Electronic Components (IECQ) IEC QC 001002: 1986. Rules of Procedure of the IEC Quality Assessment System for Electronic Components (IECQ) IEC Guide 102: 1989, Electronic components - Specification structures for qualit

26、y assess- ment (Qualification approval and capability approval) IS0 8601 : 1988, Data elements and interchange formats - Information interchange - Page 5 EN 61313-1 : 1997 IECQ CQC Capability Qualifying Component CDS Customer Detail Specification QPL Qualified Products List NSI National Supervisory

27、Inspectorate IEC Quality Assessment System for Electronic Components 2 Requirements 2.1 Capability approval Components and cable assemblies furnished to this specification shall be authorized by the NSI for listing on the QPL under the capability approval procedure in accordance with 11.7.7 of IEC Q

28、C O01 002. 2.2 Classification Components and cable assemblies furnished to this specification shall be classified by assessment level. In addition, they may be classified by climatic and environmental categories. 2.2.1 Climatic category Climatic category is defined in appendix A of IEC 68-1. The fol

29、lowing are preferred values which may be specified. Low temperature *C -5 -10 -25 -40 -55 -65 Damp-heat duration Days 4 YO 21 56 2.3 Documentation 2.3.1 Specification system This specification is part of a four-level IEC specification system. Subsidiary specifications consist of sectional specificat

30、ions and detail specifications (according to IEC Guide 102). A8808imrnt bwl i8 the combination of the CaC periodic inspection and the lot-by-lot inspection on released product. STD.BSI BS EN bL323-L-ENGL 1777 = Lb24bb9 Ob4b232 933 Page 6 EN 61313-1 : 1997 Sectional specifications shall be prepared f

31、or each subfamily of components. The specifi- cation shall contain: 1) Any additional requirements peculiar to the subfamily. 2) Any additional quality assessment procedures peculiar to the subfamily. 3) Any standard or preferred values and severities which are peculiar to the subfamily. 4) The mini

32、mum mandatory test schedules for the subfamily. 5) One or more blank detail specifications. 2.3.2 Measurements 2.3.2.1 Reference components The description of capability (3.2.1) shall define reference components as required. 2.3.2.2 Gauges The description of capability (3.2.1) shall define gauges as

33、 required. 2.3.3 Test data sheets Prepare test data sheets for each test conducted to the capability test programme. Include the data sheets in the capability approval report (3.2.8) and in the periodic inspection report (3.3.2.3). Include the following minimum Information in each data sheet: - titl

34、e of test and date; - a complete description of the capability qualifying component(s) including the type of fibre, the type of cable, and the components; - test equipment used and date of latest calibration; - all applicable test details; - all measurement values and observations; - sufficiently de

35、tailed documentation to provide traceable information for failure analysis (see 3.2.6 and 3.3.2.4). 2.3.4 Safety warnings Each detail specification shall include the following warning: Care should be taken when handling small diameter optical fibre to prevent puncturing the skin, especially in the e

36、ye area. Direct viewing of an optical fibre. when it is propagat- ing energy, is not recommended unless prior assurance has been obtained as to the safe energy output level.“ Page 7 EN 61313-1 : 1997 I 2.4 Design and Construction 2.4.1 Materials 2.4.1.1 Corrosion resistance All materials used in the

37、 construction of components or cable assemblies shall be corrosion resistant or shall be suitably finished to meet the requirements of the detail specif cat ion. 2.4.1.2 Non-flammable materials When non-flammable materials are required, the requirement shall be specified in the detail specification

38、and IEC 695-2-2 shall be referenced. 2.4.2 Workmanship Components or cable assemblies shall be manufactured to a uniform quality. The appro- priate manufacturers instructions for use shall be followed when applying components to the fibre/cable. - Particular attention shall be given to neatness and

39、thoroughness of marking, soldering, bonding, etc. 2.5 Quality assessment The quality assessment procedures of clause 3 shall control the quality of components and Gable assemblies covered by this specification. 2.6 Identification and marking Components, cable assemblies, associated hardware and pack

40、ages shall be pmianently and legibly marked as required by the detail specification. - E - = II I - - * * vi I 2.6.1 Component or cable assembly marking The preferred order of marking for components or cable assemblies is: 1) manufacturers identification mark; 2) manufacturing date code; 3) manufact

41、urers part number. 2.6.2 Package marking The preferred order of marking components or cable assemblies is: 1) manufacturers identification mark; 2) manufacturers part number; 3) manufacturing date code (year/week) (see IS0 8601); 4) assessment level(s): Page 8 EN 61313-1 : 1997 5) climatic category;

42、 6) environmental category: 7) additional marking required by the detail specification. 8 Quality assessment procedures Procedures for quality assessment and release of components or cay. assemblies consist of: - capability approval (2.1); - quality conformance inspection (3.3). 3.1 Primary skage of

43、 manufacture The primary stage of manufacture for components or cable assemblies covered by this specification Is defined at the manufacturing stage when the parts which make up the individual component or cable assembly are aggregated into the product defined in the detail specification. . Subcontr

44、acting of the primary stage and subsequent stages is permitted. 3.2 Capablty approval prOC8dUfeS 3.2.1 Description of capability The manufacturer shall prepare a description of capability in accordance with 11.7.3.2 of IEC QC 001 002. The description shall include: a) th8 limits of capabflity; b) th

45、e design rules; c) a process flow chart, including inspection points; d) a list of the specifications for the material and parts used; e) a list of the specifications for the inspections to be carried out; f) a list of the fibres, cables, and components by manufacturers part number. 3.2.2 Capability

46、 qualifying component The capability qualifying component may consist of a complete component or cable assembly or any indivklual subassembly or test piece which will demonstrate the limits of capability defined in the description of capability (3.2.1). 3.2.3 CapabiMy fest pfogmmme The manufacturer

47、shall provide a capability test programme in accordance with 11.7.3.3 of IEC QC 001002. The programme shall include: a) a description of the CQCs to be used as specimens in the capability approval tests, including instructions for use (see 3.2.2); Page 9 EN 61313-1 : 1997 b) a description of the cou

48、nterpart components.; c) the test schedules for capability approval and a test plan. The test plan shall include a complete schedule of test events along with the test requirements; d) the assessment level; e) the climatic category, If specified; f) the environmental category, if specified; g) the t

49、est schedules as specified in the applicable sectional specification for periodic inspection of the CQCs (groups C and D) and a test plan. The test plan shall include a complete schedule of test events, together with the test requirements. The manufacturer shall obtain approval for the test programme from the NSI. 3.2.4 Preparation of specimens The CQCs shall be prepared for testing according to the instructions for use defined in the capability test programme (3.2.3). 3.2.5 Capability approval testing Manufacturers shall conduct the