EN 61300-3-15-2007 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-15 Examinations and measurements - Dome eccentrici.pdf

《EN 61300-3-15-2007 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-15 Examinations and measurements - Dome eccentrici.pdf》由会员分享，可在线阅读，更多相关《EN 61300-3-15-2007 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-15 Examinations and measurements - Dome eccentrici.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 61300-3-15:2007Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-15: Examinations and measurements Dome eccentricity of a convex polished ferrule endface The European Standard EN 61300-3-15:2007 has the status of a British S

2、tandardICS 33.180.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 61300-3-15:2007This British Standard was published under the authority of

3、the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 580 50307 8National forewordThis British Standard was published by BSI. It is the UK implementation of EN 61300-3-15:2007. It is identical with IEC 61300-3-15:2006. It supersedes BS EN 61300-3.15:1997 which is withdrawn.

4、The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented on GEL/86/2 can be obtained on request to its secretary.This publication does no

5、t purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 61300-3-15 NORME EUROPENNE

6、 EUROPISCHE NORM February 2007 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2007 CENELEC - All rights of exploitation in any

7、form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-3-15:2007 E ICS 33.180.20 Supersedes EN 61300-3-15:1997English version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-15: Examinations and measurements - Dome

8、eccentricity of a convex polished ferrule endface (IEC 61300-3-15:2006) Dispositifs dinterconnexion et composants passifs fibres optiques - Mthodes fondamentales dessais et de mesures - Partie 3-15: Examens et mesures - Dcentrage du dme de la face terminale dune frule polie convexe (CEI 61300-3-15:2

9、006) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- und Messverfahren - Teil 3-15: Untersuchungen und Messungen - Exzentrizitt eines konvex polierten Stiftes(IEC 61300-3-15:2006) This European Standard was approved by CENELEC on 2006-11-01. CENELEC members are bound

10、 to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Cen

11、tral Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same s

12、tatus as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway,

13、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 61300-3-15:2006 2 Foreword The text of document 86B/2371/FDIS, future edition 2 of IEC 61300-3-15, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre

14、 optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-3-15 on 2006-11-01. This European Standard supersedes EN 61300-3-15:1997. EN 61300-3-15:2007 prescribes only an interference method though EN 61300-3-15:1997 prescribed a Newton ring method as well as an

15、interference method. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow)

16、2009-11-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 61300-3-15:2006 was approved by CENELEC as a European Standard without any modification. _ 3 EN 61300-3-15:2006 CONTENTS 1 Scope 4 2 Normative reference .4 3 General description 4 3.1 Apex

17、eccentricity .4 3.2 Interference method.5 4 Apparatus.5 5 Procedure 6 6 Details to be specified 8 Bibliography .9 Annex ZA (normative) Normative references to international publications with their corresponding European publications 10 Figure 1 Definition of apex eccentricity .4 Figure 2 Example of

18、displacement of ring centre for ferrule rotation 6 Figure 3 Example of set-up for eccentricity measurement .7 EN 61300-3-15:2006 4 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-15: Examinations and measurements Dome eccentricity of a convex p

19、olished ferrule endface 1 Scope This part of IEC 61300 describes measurement of dome eccentricity of a spherically polished ferrule endface according to an interference method. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated

20、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2538, Geometrical Product Specifications (GPS) Series of angles and slopes on prisms. 3 General description 3.1 Apex eccentricity Apex eccentrici

21、ty (X) is defined as the distance between the axis of the ferrule and the line parallel to the axis which passes through the vertex or highest point on the dome formed by spherically polishing the ferrule, as shown in Figure 1. Vertex or highest point on dome Apex eccentricity (X) FerruleAxis of fer

22、rule IEC 1806/06 Figure 1 Definition of apex eccentricity 5 EN 61300-3-15:2006 The eccentricity may be directly determined as the distance between the centre of the fibre or fibre hole and the centre of the interference ring. In this case, the eccentricity measurement will be affected by any misalig

23、nment of the measuring system, especially the angular offset between the ferrule axis and the interferometric axis. The measured dome eccentricity of angle polished ferrules is affected by further offsets caused by the tolerances of the keying position. The alignment of the measuring system shall be

24、 strictly checked and adjusted. In the method used, errors due to misalignment of the measuring system can be reduced by rotating the ferrule around its axis and observing the maximum displacement of the centre of interference rings. The dome eccentricity is one-half of the maximum displacement. 3.2

25、 Interference method This method uses an interferometer and a microscope with a camera. Interference is created between the reference beam and the beam reflected from the ferrule endface, and the interference ring is observed. The ferrule is rotated around its axis. The displacement of the centre of

26、 the interference ring is observed. The eccentricity is determined as one-half of the maximum displacement. 4 Apparatus The interference method requires the following material: a V-groove or precision sleeve mounted on a micro-manipulator (according to ISO 2538, the preferred angle for the V-groove

27、is 108); an interferometer; a microscope with camera; a monitor; a light source EN 61300-3-15:2006 6 5 Procedure 2XO1O2Axis of the ferrule O1Centre of the ring before rotation O2Centre of the ring after rotation (180) IEC 1807/06 Figure 2a Ideal measurement when the measuring system has no misalignm

28、ent 2XO1O2Ideal ferrule axis Ideal centre of the ferrule Actual centre of the ferrule Ferrule position with ideal measuring system alignment Ferrule position with some measuring system misalignment Actual ferrule axis Angular offset Vertex or highest point on dome O1Centre of the ring before rotatio

29、n O2Centre of the ring after rotation (180) IEC 1808/06 Figure 2b Actual measurement when the measuring system has any angular offset Figure 2 Example of displacement of ring centre for ferrule rotation 7 EN 61300-3-15:2006 a) Place the ferrule in the V-groove or the precision sleeve. b) Position th

30、e ferrule into a visual field of the TV screen using the micro-manipulator. c) Observe the interference ring and record the position of the centre of the ring (see Figure 3). d) Rotate the ferrule through 180. Record the second position of the centre of the ring. e) Record the displacement 2X of the

31、 centre of the interference ring. The dome eccentricity is one-half of the maximum displacement (also see Figures 2a and 2b). Interference ring Centre of the interference ring Ferrule, inner diameter Ferrule, outer diameter Microscope with camera Mirror Light source Half-mirror Ferrule V-groove or p

32、recision lCentre of the ferrule IEC 1809/06 NOTE The eccentricity may be determined by recording three or more positions of the ring centre on its circle locus as the ferrule is rotated and by calculating the radius of the least squares circle. Figure 3 Example of set-up for eccentricity measurement

33、 For the measurement of angled polished ferrules the rotation of the ferrule around its axis is not possible and should be replaced by a guaranteed calibration of the alignment system prior to the measurement. The alignment system is then rotated to compensate the nominal polishing angle. EN 61300-3

34、-15:2006 8 6 Details to be specified The following details, as applicable, shall be specified in the relevant specification: maximum allowable repeatability of measuring system; allowable dome eccentricity. 9 EN 61300-3-15:2006 Bibliography IEC 61300-1, Fibre optic interconnecting devices and passiv

35、e components Basic test and measurement procedures Part 1: General and guidance _ NOTE Harmonized as EN 61300-1:2003 (not modified). EN 61300-3-15:2006 10 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced d

36、ocuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifica

37、tions, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year ISO 2538 -1)Geometrical Product Specifications (GPS) - Series of angles and slopes on prisms EN ISO 2538 20032)1)Undated reference. 2)Valid edition at date of issue. blankBS EN 61300-3-15:2007BSI389 Chiswick Hig

38、h RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment

39、or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would in

40、form the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest ed

41、itions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to

42、 orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Lib

43、rary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kep

44、t up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to B

45、ritish Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization

46、bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the fr

47、ee use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.