EN 60335-2-89-2010 en Household and similar electrical appliances - Safety - Part 2-89 Particular requirements for commercial refrigerating appliances with an incorporated or remot.pdf

《EN 60335-2-89-2010 en Household and similar electrical appliances - Safety - Part 2-89 Particular requirements for commercial refrigerating appliances with an incorporated or remot.pdf》由会员分享，可在线阅读，更多相关《EN 60335-2-89-2010 en Household and similar electrical appliances - Safety - Part 2-89 Particular requirements for commercial refrigerating appliances with an incorporated or remot.pdf（54页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationHousehold and similar electricalappliances SafetyPart 2-89: Particular requirements for commercialrefrigerating appliances with an incorporated orremote refrigerant condensing unit or compressorBS EN 60335-2-89:2010+A1:2016BS EN 60335-2-89:2010+A1:2016 BRITISH STANDARDNation

2、al forewordThis British Standard is the UK implementation of EN 60335-2-89:2010+A1:2016. It is derived from IEC 60335-2-89:2010, incorporating amendment 1:2012. It supersedes BS EN 60335-2-89:2010, which will be withdrawn on 17 August 2018.The start and finish of text introduced or altered by amendm

3、ent is indicated in the text by tags. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by .Where a common modification to an IEC amendment has been introduced, the tags carry the number of the amendment. For example,

4、 the common modifications introduced by CENELEC to IEC amendment 1 are indicated by .The UK participation in its preparation was entrusted to Technical Committee CPL/61, Safety of household and similar electrical appliances.A list of organizations represented on this committee can be obtained on req

5、uest to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 74819 6ICS 97.130.20Compliance with a Britis

6、h Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2010.Amendments/corrigenda issued since publicationDate Text affected31 March 2016 Implementation of IEC amendment 1:2012 with C

7、ENELEC modificationsEUROPEAN STANDARD EN 60335-2-89NORME EUROPENNE EUROPISCHE NORMMarch 2010CENELEC European Committee forElectrotechnicalStandardization Comit Europen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat:Avenue Marnix 17, B - 1000 Brus

8、sels 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELECmembers.Ref. No. EN 60335-2-89:2010 EICS 97.130.20 Supersedes EN 60335-2-89:2002 + A1:2005 + A2:2007 + A11:2004English versionHousehold and similar electrical appliances - Safety - Part 2-89: Pa

9、rticular requirements for commercialrefrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor (IEC 60335-2-89:2010)Appareils lectrodomestiques et analogues -Scurit - Partie 2-89: Rglesparticulires pour les appareils de rfrigration usage commercialavec une unit

10、 de condensation du fluide frigorigne ou un compresseur incorpors ou distance(CEI 60335-2-89:2010)Sicherheitelektrischer Gerte fr den Hausgebrauch und hnliche Zwecke - Teil 2-89: Besondere Anforderungen fr gewerbliche Khl-/Gefriergerte mit eingebautem oder getrenntemVerflssigersatz oder Motorverdich

11、ter(IEC 60335-2-89:2010)This European Standard was approved by CENELEC on 2010-03-01. CENELEC members are bound to complywith the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lis

12、ts and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any otherlanguage made by translation under the res

13、ponsibility of a CENELEC member into its own language and notifiedto the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France

14、, Germany, Greece, Hungary, Iceland, Ireland, Italy,Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,Spain, Sweden, Switzerland and the United Kingdom.BS EN 60335-2-89:2010EN 60335-2-89:2010+A1February 2016EN 60335-2-89:2010 - 2 -ForewordTh

15、e text of document 61C/460/FDIS, future edition 2 of IEC 60335-2-89, prepared by SC 61X of theIEC Technical Committee 61, Safetyof household and similar electrical appliances, was submitted to theIEC-CENELEC parallel vote and was approved by CENELEC asEN 60335-2-89 on 2010-03-01.This European Standa

16、rd supersedes EN 60335-2-89:2002, EN 60335-2-89:2002/A1:2005, EN 60335-2-89:2002/A2:2007 and EN 60335-2-89:2002/A11:2004.The principal changes in this edition as compared with EN 60335-2-89:2002 are as follows (minorchanges are not listed): aligns the textwith EN 60335-1, and its Amendments 1, 2, 11

17、, 12 and 13; introduces requirements for appliances using transcritical refrigerant systems (3.107, 3.108, 3.109, 3.110, 3.111, 7.1, 7.6, 7.12.1, 22.103, 24.1.4, 24.102); introduces an enhanced flexing test (23.3).Attention is drawn to the possibility that some of the elements of this document may b

18、e the subject of patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patentrights.The following dates were fixed:-latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010

19、-12-01-date on which national standardsconflicting with the EN have to be withdrawn (dow) 2013-03-01This Part 2 has to be used in conjunction with EN 60335-1, Household and similar electrical appliances Safety Part 1: General requirements. It was established on the basis of the 2002 edition of thats

20、tandard. Amendments and revisions of Part 1 have also to be taken into account and the dates when such changes become applicable will be stated in the relevant amendment or revision of Part 1.This Part 2 supplements ormodifies the corresponding clauses of EN 60335-1, so as to convert it into theEuro

21、pean Standard: Safety requirements for electric appliances - Safety - Part 2-89: Particularrequirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressorWhen a particular subclause of Part 1 is not mentioned in this Part 2, that subclaus

22、e applies as far as is reasonable.When this standard states “addition“, “modification“ or “replacement“, the relevant textofPart 1 is to be adapted accordingly.NOTE 1 The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are additional to those in

23、 Part 1; unless notes are in a new subclause or involve notes in Part 1,they are numbered starting from 101, including those in areplaced clause or subclause; additional annexes are lettered AA, BB, etc.; subclauses, notes and annexes that are additional to those in the IEC standard are prefixed wit

24、h the letter Z.NOTE 2 The following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type.Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated nounare also in bold.BS

25、EN 60335-2-89:2010- 3 -EN 60335-2-89:2010There are no special national conditions causing a deviation from this European Standard, other thanthose listed in Annex ZA to EN 60335-1.There are no national deviations from this European Standard, other than those listed in Annex ZB toEN 60335-1.p NOTE In

26、 this document, p is used in themargin to indicate instructions for preparing the printed version._BS EN 60335-2-89:2010EN 60335-2-89:2010 - 4 -Introductionp Add:An investigation by CENELEC TC 61 has shown that all risks from products within the scope of thisstandard are fully covered by the Low Vol

27、tage Directive, 2006/95/EC. Forproducts having mechanical moving parts, a risk assessment in accordance with the Machinery Directive, 2006/42/EC, has shown thatthe risks are mainly of electrical origin and consequently this directive is not applicable. However, therelevant essential safety requireme

28、nts of the Machinery Directive are covered by this standard togetherwith the principal objectives of the Low Voltage Directive._Endorsement noticeThe text of the International Standard IEC 60335-2-89:2010 was approved by CENELEC as a EuropeanStandard without any modification._Bibliographyp Add the f

29、ollowing notes to the standards mentioned:IEC 60079 seriesNOTE Harmonized in EN 60079 series (partiallymodified).IEC 60335-2-24 NOTE Harmonized as EN 60335-2-24.IEC 60335-2-75 NOTE Harmonized as EN 60335-2-75.ISO 13732-1 NOTEHarmonized as EN ISO 13732-1.ISO 23953-2 NOTEHarmonized as EN ISO 23953-2._

30、BS EN 60335-2-89:2010 2 BS EN 60335-2-89:2010+A1:2016EN 60335-2-89:2010+A1:2016- 3 -EN 60335-2-89:2010There are no special national conditions causing a deviation from this European Standard, other thanthose listed in Annex ZA to EN 60335-1.There are no national deviations from this European Standar

31、d, other than those listed in Annex ZB toEN 60335-1.p NOTE In this document, p is used in themargin to indicate instructions for preparing the printed version._BS EN 60335-2-89:2010EN 60335-2-89:2010 - 4 -Introductionp Add:An investigation by CENELEC TC 61 has shown that all risks from products with

32、in the scope of thisstandard are fully covered by the Low Voltage Directive, 2006/95/EC. Forproducts having mechanical moving parts, a risk assessment in accordance with the Machinery Directive, 2006/42/EC, has shown thatthe risks are mainly of electrical origin and consequently this directive is no

33、t applicable. However, therelevant essential safety requirements of the Machinery Directive are covered by this standard togetherwith the principal objectives of the Low Voltage Directive._Endorsement noticeThe text of the International Standard IEC 60335-2-89:2010 was approved by CENELEC as a Europ

34、eanStandard without any modification._Bibliographyp Add the following notes to the standards mentioned:IEC 60079 seriesNOTE Harmonized in EN 60079 series (partiallymodified).IEC 60335-2-24 NOTE Harmonized as EN 60335-2-24.IEC 60335-2-75 NOTE Harmonized as EN 60335-2-75.ISO 13732-1 NOTEHarmonized as

35、EN ISO 13732-1.ISO 23953-2 NOTEHarmonized as EN ISO 23953-2._BS EN 60335-2-89:2010 3 BS EN 60335-2-89:2010+A1:2016EN 60335-2-89:2010+A1:2016 4 BS EN 60335-2-89:2010+A1:2016EN 60335-2-89:2010+A1:2016EN 60335-2-89:2010/A1:2016 2 European foreword This document (EN 60335-2-89:2010/A1:2016) consists of

36、the text of IEC 60335-2-89:2010/A1:2012 prepared by SC 61C “Safety of refrigeration appliances for household and commercial use“ of IEC/TC 61 “Safety of household and similar electrical appliances“, together with the common modifications prepared by CLC/TC 61, “Safety of household and similar electr

37、ical appliances“. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-08-12 latest date by which the national standards conflicting with the document have to be withdraw

38、n (dow) 2019-02-12 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This amendment supplements or modifies the corresponding clauses of

39、 EN 60335-1:2012 and EN 60335-2-89:2010. Clauses, subclauses, notes, tables and annexes which are additional to those in IEC 60335-2-89:2010/A1:2012 or in IEC 60335-1:2010 are prefixed “Z”. This document has been prepared under a mandate given to CENELEC by the European Commission and the European F

40、ree Trade Association, and supports essential requirements of EU Directive. For the relationship with EU Directive 2006/42/EC, see informative Annex ZZ, which is an integral part of this document. Endorsement notice The text of the International Standard IEC 60335-2-89:2010/A1:2012 was approved by C

41、ENELEC as a European Standard with agreed common modifications. Foreword to amendment A1- 5 -EN 60335-2-89:2010p Add:Annex ZC(normative)Normative references to international publications with their corresponding European publications Addition:Publication Year Title EN/HD YearIEC 60079-41)-Electrical

42、 apparatus for explosive gasatmospheres -Part 4: Method of test for ignition temperature- - IEC 60079-4A2)-Electrical apparatus for explosive gasatmospheres -Part 4: Method of test for ignition temperature - First supplement to IEC 60079-4:1966- - IEC 60079-15 2005 Electrical apparatus for explosive

43、 gasatmospheres -Part 15: Construction, test and marking oftype of protection “n“ electrical apparatusEN 60079-15 2005IEC/TR 60079-20 -Electrical apparatus for explosive gasatmospheres -Part 20: Data for flammable gases and vapours, relating to the use of electricalapparatus- - IEC 60335-2-5- Househ

44、old and similar electrical appliances -Safety -Part 2-5: Particular requirements fordishwashers EN 60335-2-520032009IEC 60335-2-34+ A1+ A2200220042008Household and similar electrical appliances -Safety -Part 2-34: Particular requirements for motor-compressorsEN 60335-2-34+ A1+ A2+ A11200220052009200

45、4ISO 817 -Organic refrigerants - Number designation -ISO 3864-1-Graphical symbols - Safetycolours and safetysigns -Part 1: Design principles for safety signs in workplaces and public areas- - ISO 4126-22003 Safetydevices for protection against excessive pressure - Part 2: Bursting disc safety device

46、s- - ISO 5149-Mechanical refrigerating systems used forcooling and heating - Safety requirements- - _1)IEC 60079-4 is superseded by IEC 60079-20-1:2010.2)IEC 60079-4A is superseded by IEC 60079-20-1:2010.BS EN 60335-2-89:2010- 5 N 60335-2-89:2010p Add:Annex ZC(normative)Normative references to inter

47、national publications with their corresponding European publications Addition:Publication Year Title N/HD YearIEC 60079-41)lectrical apparatus for explosive gasatmospheres -Part 4: Method of test for ignition temperature- - IEC 60079-4A2)-Electrical apparatus for explosive gasatmospheres -Part 4: Me

48、thod of test for ignition temperature - First supplement to IEC 60079-4:1966- - IEC 60079-15 2005 Electrical apparatus for explosive gasatmospheres -Part 15: Construction, test and marking oftype of protection “n“ electrical apparatusEN 60079-15 2005IEC/TR 60079-20 -Electrical apparatus for explosiv

49、e gasatmospheres -Part 20: Data for flammable gases and vapours, relating to the use of electricalapparatus- - IEC 60335-2-5- Household and similar electrical appliances -Safety -Part 2-5: Particular requirements fordishwashers EN 60335-2-520032009IEC 60335-2-34+ A1+ A2200220042008Household and similar electrical appliances -Safety -Part 2-34: Particular requirements for motor-compressorsEN 60335-2-34+ A1+ A2+ A112002200520092004I