EN 50411-3-8-2016 en Fibre organizers and closures to be used in optical fibre communication systems - Product specifications - Part 3-8 Fibre management system terminal equipment .pdf

《EN 50411-3-8-2016 en Fibre organizers and closures to be used in optical fibre communication systems - Product specifications - Part 3-8 Fibre management system terminal equipment .pdf》由会员分享，可在线阅读，更多相关《EN 50411-3-8-2016 en Fibre organizers and closures to be used in optical fibre communication systems - Product specifications - Part 3-8 Fibre management system terminal equipment .pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 50411-3-8:2016Fibre organizers and closuresto be used in optical fibrecommunication systems Product specificationsPart 3-8: Fibre management system,terminal equipment box type 1 for categoryCBS EN 50411-3-8:2016 BRITISH STANDARDNational forewordThis British Standard is

2、 the UK implementation of EN 50411-3-8:2016.The UK participation in its preparation was entrusted to Technical Committee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented on this committee can be obtained on request to its secretary.This publica

3、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 78810 9 ICS 33.180.20; 33.180.99 Compliance with a British Standard cannot conf

4、er immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 50411-3-8:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM

5、 EN 50411-3-8 January 2016 ICS 33.180.20; 33.180.99 English Version Fibre organizers and closures to be used in optical fibre communication systems - Product specifications - Part 3-8: Fibre management system, terminal equipment box type 1 for category C Organiseurs et botiers de fibres destins tre

6、utiliss dans les systmes de communication par fibres optiques - Spcifications de produits - Partie 3-8: Systme de gestion des fibres, botier dquipement terminal de type 1 pour la catgorie C LWL-Spleikassetten und -Muffen fr die Anwendung in LWL-Kommunikationssystemen - Produktspezifikationen - Teil

7、3-8: Faser Management System, Kasten fr Endeinrichtungen Typ 1 fr Kategorie C This European Standard was approved by CENELEC on 2015-10-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a n

8、ational standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German)

9、. A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, B

10、ulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Swit

11、zerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in

12、 any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 50411-3-8:2016 E BS EN 50411-3-8:2016Contents Page European foreword . 3 1 Scope . 5 1.1 Product definition . 5 1.2 Operating environment 5 1.3 Reliability 5 1.4 Quality assurance . 5 1.5 Allowed fibre types . 5 2 Normati

13、ve references . 5 3 Terms, definitions and abbreviations . 7 3.1 Terms and definitions 7 3.2 Abbreviations 7 4 Description 7 4.1 Optical fibre terminal equipment box housing 7 4.2 Cable fixing 8 4.3 FMS system . 8 4.4 Materials 8 4.5 Laser safety . 9 4.6 Marking and identification . 9 5 Variants 9 6

14、 Dimensional requirements . 11 7 Tests . 11 7.1 Test sample size . 11 7.2 Test sample preparation 11 7.3 Test and measurement methods. 12 7.4 Test sequence . 12 7.5 Pass/fail criteria 12 8 Test report . 13 9 Performance requirements 13 9.1 Dimensional and marking requirements 13 9.2 Ingress, optical

15、 and appearance performance criteria . 14 9.3 Mechanical ingress performance requirements 15 9.4 Environmental ingress performance requirements 16 9.5 Mechanical optical performance requirements . 17 9.6 Environmental optical performance requirements . 18 9.7 Material performance requirements . 18 A

16、nnex A (informative) Fibre for test sample details . 19 Annex B (normative) Sample size and product sourcing requirements 20 Annex C (informative) Performance of copper cabling and connectivity 21 Bibliography . 22 BS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:2016European foreword This

17、document (EN 50411-3-8:2016) has been prepared by CLC/TC 86BXA “Fibre optic interconnect, passive and connectorised components“. The following dates are fixed: latest date by which this document has to be implemented at national level by publication of an identical national standard or by endorsemen

18、t (dop) 2016-10-12 latest date by which the national standards conflicting with this document have to be withdrawn (dow) 2018-10-12 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible f

19、or identifying any or all such patent rights. BS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:2016Fibre organizers and closures to be used in optical fibre communication systems Product specifications Part 3-8: Fibre management system, terminal equipment box type 1 for category C Descripti

20、on Performance Construction: Wall mounted box Cable Fixing: Mechanical Connectors: EN 50377 series EN 60603-7 Series Fibre types: EN 60793-2-50 B1 and B6 Fibre management: Integrated in box Applications: Optical Fibre Terminal Equipment Box including the ONT/CPE for indoor controlled environments EN

21、 61753-1 Category C Sealing performance: IP 40 Related documents: EN 60529 Degrees of protection provided by enclosures (IP Code) (IEC 60529) EN 60793-2-50 Optical fibres Part 2-50: Product specifications Sectional specification for class B single-mode fibres (IEC 60793-2-50) EN 61753-1 Fibre optic

22、interconnecting devices and passive components Part 1: General and guidance for performance standard (IEC 61753-1) EN 61300 series Fibre optic interconnecting devices and passive components Basic test and measurement procedures (IEC 61300 series) Shape Maximum outline dimensions Rectangular shape Wi

23、dth: 300 mm Height: 150 mm Depth: 100 mm Square shape Width: 210 mm Height: 210 mm Depth: 50 mm Circular Diameter: 250 mm Depth: 100 mm DepthHeightWidthDepthDiameterBS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:20161 Scope 1.1 Product definition This European Standard specifies the dimen

24、sional, optical, mechanical and environmental performance requirements of a Terminal Equipment Boxes for the FTTX networks. The Terminal Equipment Box will house the ONT/CPE (electronics) and it protects the optical fibres, splices and connectors from direct contact with the user. Optionally it can

25、contain the network test interface, the power supply and the batteries. The performance of the electronics, power supply or batteries are not part of this document. These are covered by another EN document, EN 50700. This specification contains the initial, start of life optical, mechanical and envi

26、ronmental performance requirements of the optical fibre termination in a Terminal Equipment Box, in order for it to be categorized as an EN standard product. 1.2 Operating environment The tests selected combined with the severity and duration is representative of indoor and outside plant for above g

27、round environments defined by: EN 61753-1 Category C Controlled environment 1.3 Reliability Whilst the anticipated service life expectancy of the product in this environment is 20 years, compliance with this specification does not guarantee the reliability of the product. This should be predicted us

28、ing a recognised reliability assessment programme. 1.4 Quality assurance Compliance with this specification does not guarantee the manufacturing consistency of the product. This should be maintained using a recognised quality assurance programme. 1.5 Allowed fibre types All EN 60793-2-50 fibres can

29、be stored in the Terminal Equipment Box with a minimum storage radius of 20 mm (up to a length of maximum 2 m). Smaller storage radii down to 15 mm are possible with the EN 60793-2-50 B6_a fibre types, but in this case the reduction in mechanical reliability should be taken into account (see Annex A

30、). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any am

31、endments) applies. EN 50377 (all parts), Connector sets and interconnect components to be used in optical fibre communication systems Product specifications EN 50700, Information technology Premises distribution access network (PDAN) cabling to support deployment of optical broadband networks EN 605

32、29, Degrees of protection provided by enclosures (IP Code) (IEC 60529) BS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:2016EN 60695-11-10, Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods (IEC 60695-11-10) EN 60754-1, Test on gases evolved during

33、combustion of materials from cables Part 1: Determination of the halogen acid gas content (IEC 60754-1) EN 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for class B single-mode fibres (IEC 60793-2-50) EN 60825-2, Safety of laser products Part 2: Safety of optic

34、al fibre communication systems (OFCS) (IEC 60825-2) EN 61034-2, Measurement of smoke density of cables burning under defined conditions Part 2: Test procedure and requirements (IEC 61034-2) EN 61300-2-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures

35、 Part 2-1: Tests Vibration (sinusoidal) (IEC 61300-2-1) EN 61300-2-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-4: Tests Fibre/cable retention (IEC 61300-2-4) EN 61300-2-9, Fibre optic interconnecting devices and passive components Basic

36、test and measurement procedures Part 2-0: Tests Shock (IEC 61300-2-9) EN 61300-2-12, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-12: Tests Impact (IEC 61300-2-12) EN 61300-2-22, Fibre optic interconnecting devices and passive components Bas

37、ic test and measurement procedures Part 2-22: Tests Change of temperature (IEC 61300-2-22) EN 61300-2-33, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-33: Tests Assembly and disassembly of fibre optic mechanical splices, fibre management sys

38、tems and closures (IEC 61300-2-33) EN 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination (IEC 61300-3-1) EN 61300-3-3, Fibre optic interconnecting devices and passive components Basic

39、test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and return loss (IEC 61300-3-3) EN 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements A

40、ttenuation (IEC 61300-3-4) EN 61300-3-28, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-28: Examinations and measurements Transient loss (IEC 61300-3-28) BS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:20163 Terms, definitions and a

41、bbreviations 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 fibre management system system to control fibre routing from the incoming to the out-going fibres, containing one or more splice cassettes and additional functional elements, an

42、d which provides a means for routing, storing and protecting of fibre splices, connectors or other passive optical devices in a predetermined order, from one cable sheath opening to another 3.1.2 external network test interface ENTI test point which defines the service maintenance boundary of an acc

43、ess network at which external service provision may be assessed and which can be associated with protection devices 3.1.3 microduct system system that provides for routing air blown fibres or microduct fibre units, between hollow conduits (microducts), and interconnects the microducts by use of pneu

44、matic connectors, tube welding, crimp connectors or push on connectors 3.2 Abbreviations FMS Fibre Management System CPE Customer Premises Equipment ONT Optical Network Terminal ENTI External Network Test Interface CATV Cable Television 4 Description 4.1 Optical fibre terminal equipment box housing

45、The terminal equipment box provides: facilities for mounting and protection of stored fibres, connectors, network test interface ENTI (optional), electronics (ONT/CPE), power supply (optional) and batteries (optional), access by user to the electrical data, CATV and telephone outputs, a protected fi

46、bre management system for storing fibres, connectors and splices, sealing of input and output optical and electrical cables. This also includes terminal equipment boxes used for microduct cable or fibre. The design of the terminal equipment housing shall allow the jointing or termination of minimum

47、one incoming cable to the specified number of optical connectors. Examples of typical terminal equipment applications are given in Figure 1. BS EN 50411-3-8:2016 EN 50411-3-8:2016 (E)BS EN 50411-3-8:2016Fully integrated Modular Figure 1 Examples of terminal equipment applications 4.2 Cable fixing Ca

48、ble or microduct fixing will be secured by means of mechanical attachment. Axial movement of the fibre with respect to the microduct shall be taken into account. 4.3 FMS system The fibre management system provides means for routing, storing and protecting optical fibre and/or fibre splices, connecto

49、rs or other passive optical devices. 4.4 Materials All materials that are likely to come in contact with personnel shall meet appropriate health and safety regulations. The Terminal Equipment Box materials shall be compatible with each other and with the materials of the cables and/or microducts. All components of the wall outlet shall be resistant to solvents and degreasing agents that are typically used to clean and degrease fibres and cables. Metallic parts shall