EN 15507-2017 en Packaging - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades.pdf

《EN 15507-2017 en Packaging - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades.pdf》由会员分享，可在线阅读，更多相关《EN 15507-2017 en Packaging - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Packaging Transport packaging for dangerous goods Comparative material testing of polyethylene gradesBS EN 15507:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15507 November 2017 ICS 13.300; 55.040 Supersedes

2、 EN 15507:2008English Version Packaging - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades Emballages - Emballages pour le transport des marchandises dangereuses - Essais comparatifs de divers grades de polythylne Verpackung - Verpackungen zur Befrderung

3、gefhrlicher Gter - Vergleichende Werkstoffprfung von Polyethylensorten This European Standard was approved by CEN on 11 September 2017. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

4、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

5、in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

6、 Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United King

7、dom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15507:2

8、017 ENational forewordThis British Standard is the UK implementation of EN 15507:2017. It supersedes BS EN 15507:2008, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PKW/0/4, Packaging - Dangerous Goods.A list of organizations represented on this comm

9、ittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 87068 2ICS 13.300

10、; 55.040Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 15

11、507:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15507 November 2017 ICS 13.300; 55.040 Supersedes EN 15507:2008English Version Packaging - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades Emballages - Emballages pour le transport des marchand

12、ises dangereuses - Essais comparatifs de divers grades de polythylne Verpackung - Verpackungen zur Befrderung gefhrlicher Gter - Vergleichende Werkstoffprfung von Polyethylensorten This European Standard was approved by CEN on 11 September 2017. CEN members are bound to comply with the CEN/CENELEC I

13、nternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

14、any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official

15、 versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

16、way, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights

17、 of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15507:2017 EBS EN 15507:2017EN 15507:2017 (E) 2 Contents Page European foreword . 3 Introduction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Test requirements 6 4.1 General 6

18、 4.2 Melt mass-flow rate (MFR). 6 4.3 Density 6 4.4 Low temperature notched impact strength . 7 4.5 Environmental stress crack resistance . 7 4.6 Molecular degradation 7 4.7 Test report . 7 5 Test specimens . 8 5.1 Selection of test materials 8 5.2 Test sheet preparation 8 6 Facilities for testing 8

19、 7 Test procedure . 8 7.1 Melt mass-flow rate 8 7.2 Density 9 7.3 Notched impact strength 9 7.4 Environmental stress crack resistance Full notch creep test (FNCT) . 9 7.5 Molecular degradation by melt mass-flow rate increase 10 8 Selective testing 10 Bibliography . 12 BS EN 15507:2017EN 15507:2017 (

20、E) 3 European foreword This document (EN 15507:2017) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at t

21、he latest by May 2018, and conflicting national standards shall be withdrawn at the latest by May 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent right

22、s. This document supersedes EN 15507:2008. The main changes with respect to the previous edition are listed below: a) The introductory texts for “Normative references“ and “Terms and definitions” have been modified. b) Clause 2 “Normative references” has been revised. c) The references to withdrawn

23、standards EN ISO 16101, EN ISO 16104, EN ISO 16467 and EN ISO 23667 have been replaced by current standards EN ISO 16495 and EN ISO 13274. d) Editorial changes were made. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to i

24、mplement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roma

25、nia, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15507:2017EN 15507:2017 (E) 4 Introduction This European Standard was developed to provide requirements and test procedures for comparative testing of polyethylene grades of high and medium molecular we

26、ight high density polyethylene, used for the manufacture of packaging and IBCs for the transport of dangerous goods. These specific material parameters relate to the test procedures described in the standards: EN ISO 13274:2013, Packaging Transport packaging for dangerous goods Plastics compatibilit

27、y testing for packaging and IBCs (ISO 13274:2013 + Cor. 1:2014) EN ISO 16495:2013, Packaging Transport packaging for dangerous goods Test methods (ISO 16495:2013) The aim of the test methods described in this European Standard is to provide information for consideration as part of a selective test p

28、rocedure. Selective testing procedures, are described in Clause 8 in the standards above and can eliminate or reduce the requirement to carry out the full test procedures described each time a new grade of high density polyethylene is used for the manufacture of the same design type. The test requir

29、ements and procedures in the standards above for plastics packaging and IBCs meet the provisions set out in the multimodal United Nations Recommendations on the transport of Dangerous Goods 1. These UN Recommendations are given legal entity by the provisions of a series of modal agreements and regul

30、ations for the international transport of dangerous goods, details of which can be found in the Bibliography. These international agreements include: the European Agreement concerning the International Carriage of Dangerous goods by Road (ADR), (covering most of Europe as well as parts of Asia and N

31、orthern Africa) 2; the International Civil Aviation Organizations Technical Instructions for the Safe Transport of Dangerous Goods by Air (ICAO TIs), (world-wide) 3; the International Maritime Dangerous Goods Code (IMDG Code), (world-wide) 4; regulations concerning the International Carriage of dang

32、erous Goods by Rail (RID), (covering most of Europe, parts of North Africa and the Middle East) 5. The application of this standard will need to take account of the requirements of these international agreements and the relevant national regulations 6, 7 for domestic transport of dangerous goods. It

33、 is important to note that there will be certain modal differences from the UN Recommendations and that the schedule for revision of the UN Recommendations and modal provisions may lead to temporary inconsistencies with this European Standard, which is regularly updated to reflect the latest version

34、 of the UN Recommendations. This European Standard has been submitted for reference into the RID and/or the technical annexes of the ADR. BS EN 15507:2017EN 15507:2017 (E) 5 1 Scope This European Standard specifies material parameters, test requirements and procedures for the comparative testing of

35、polyethylene grades of high molecular weight high density polyethylene (PE-HD-HMW) and medium molecular weight high density polyethylene (PE-HD-MMW), used for the manufacture of packaging and IBCs for the transport of dangerous goods. It is intended to be used in conjunction with selective testing f

36、or packaging for liquids. The standard is not intended to be used for comparative testing of recycled plastics material. NOTE This European Standard is intended to be used in conjunction with one or more of the international regulations set out in the Bibliography. 2 Normative references The followi

37、ng documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 179-1:2010,

38、 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) EN ISO 1133-1, Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1) EN ISO 1183-1, Plastics - Me

39、thods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1) EN ISO 13274:2013, Packaging - Transport packaging for dangerous goods - Plastics compatibility testing for packaging and IBCs (ISO 13274:2013) EN ISO 164

40、95:2013, Packaging - Transport packaging for dangerous goods - Test methods (ISO 16495:2013) EN ISO 17855-2:2016, Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016) ISO 16770:2004, Plastics Determin

41、ation of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT) 3 Terms and definitions For the purposes of this document the following apply. 3.1 high molecular weight high density polyethylene PE-HD-HMW natural Polyethylene with a density of 940 kg/m3, when measured at 23

42、 C after annealing at 100 C for 30 min, and a melt mass-flow rate at 190 C/21,6 kg load of 940 kg/m3, when measured at 23 C after annealing at 100 C for 30 min, and a melt mass-flow rate at 190 C/2,16 kg load of 0,1 g/600 s in accordance with EN ISO 1133-1, or a melt mass-flow rate at 190 C/5 kg loa

43、d 0,5 g/600 s in accordance with EN ISO 1133-1 Note 1 to entry: Natural Polyethylene refers to material with no pigments or colorants. 4 Test requirements 4.1 General When a manufacturer of a plastics packaging or IBC wants to change to a new grade of high density polyethylene for its manufacture, t

44、est results to the following requirements may be used in conjunction with a selective testing procedure to reduce the amount of design type testing of the design type with the new polyethylene grade. As a minimum requirement, a test with water as the test medium in accordance with EN ISO 16495 shall

45、 be carried out for the packaging design type manufactured from the new polyethylene grade. The test requirements in 4.2 to 4.6 shall be met in the comparative testing of the polyethylene grade with existing approvals, (Material A), and the replacement polyethylene grade, (Material B). The comparati

46、ve testing of the polyethylene grades to the procedures defined in 7.1 to 7.5 shall be carried out concurrently in a single laboratory. For the procedures 7.2 to 7.5, test sheets (see 5.2) compression moulded by the same mould type (e.g. using a positive mould or semi-positive mould) shall be used.

47、4.2 Melt mass-flow rate (MFR) When tested in accordance with 7.1 the value of melt mass-flow rate shall be within the following limits: 70 % MFR Material A MFR Material B 130 % MFR Material A. NOTE The determination of melt mass-flow rate is solely intended as a classification test for the polyethyl

48、ene grade and does not relate to any of the tests for packaging described in EN ISO 13274 or EN ISO 16495. 4.3 Density When tested in accordance with 7.2 the density in kg/m3shall be: Density Material B (DB) Density Material A (DA) 2. NOTE The determination of density is intended to relate to the pe

49、rformance of packaging and IBCs produced from the polyethylene grades, such as those tested in accordance with EN ISO 16495:2013, following conditioning with standard liquids described in EN ISO 13274:2013, Clause 8: EN ISO 16495:2013, Annex F Drop test; EN ISO 16495:2013, Annex I Stacking test; EN ISO 16495:2013, Annex H Hydraulic pressure test and the Permeability test in EN ISO 13274:2013, 4.11. BS EN 15507:2017EN 15507:2017 (E) 7 4.4 Low temperature notched impact strength When tested in accordance wit