EN 15416-5-2006 5402 Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5 Determination of conventional pressing time《苯酚和氨基塑料除外.pdf

《EN 15416-5-2006 5402 Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5 Determination of conventional pressing time《苯酚和氨基塑料除外.pdf》由会员分享，可在线阅读，更多相关《EN 15416-5-2006 5402 Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5 Determination of conventional pressing time《苯酚和氨基塑料除外.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15416-5:2006Adhesives for load bearing timber structures other than phenolic and aminoplastic Test methods Part 5: Determination of conventional pressing timeThe European Standard EN 15416-5:2006 has the status of a British StandardICS 83.180g49g50g3g38g50g51g60g44g49g42g3g58g4

2、4g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIBS EN 15416-5:2006This British Standard was p

3、ublished under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006ISBN 0 580 48466 1National forewordThis British Standard was published by BSI. It is the UK implementation of EN 15416-5:2006.The UK participation in its preparation was entrusted to Technical Co

4、mmittee PRI/52, Adhesives.A list of organizations represented on PRI/52 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot con

5、fer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsLicensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15416-5August 2006ICS 83.180English VersionAdhesives for load bear

6、ing timber structures other than phenolicand aminoplastic - Test methods - Part 5: Determination ofconventional pressing timeAdhsifs pour structures portantes en bois de type autreque phnolique et aminoplaste - Mthodes dessai - Partie5 : Dtermination de la dure conventionelle sous pressionKlebstoffe

7、 fr tragende Holzbauteile ausgenommenPhenolharzklebstoffe und Aminoplaste - Prfverfahren -Teil 5: Bestimmung der MindestpresszeitThis European Standard was approved by CEN on 18 May 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi

8、ng this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions

9、 (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus,

10、 Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUR

11、OPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15416-5:2006: ELicensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00

12、2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 2 Contents Page Foreword3 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Principle5 5 Apparatus .5 6 Procedure .6 7 Expression of results 7 8 Test report 7 Bibliography 9 Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2

13、006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 3 Foreword This document (EN 15416-5:2006) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of

14、an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn at the latest by February 2007. This document is one of a series dealing with test methods for adhesives for use in load bearing timber structures. The document is published in

15、support of Eurocode 5, Common unified rules for timber structures. The series consists of seven test methods to assess the performance of adhesives after specified heat and humidity treatments: EN 302-1, Adhesives for load-bearing timber structures Test methods Part 1: Determination of bond strength

16、 in longitudinal tensile shear strength; EN 302-2, Adhesives for load-bearing timber structures - Test methods - Part 2: Determination of resistance to delamination; EN 302-3, Adhesives for load-bearing timber structures - Test methods - Part 3: Determination of the effect of acid damage to wood fib

17、res by temperature and humidity cycling on the transverse tensile strength; EN 302-4, Adhesives for load-bearing timber structures - Test methods - Part 4: Determination of the effects of wood shrinkage on the shear strength; prEN 15416-1, Adhesives for load bearing timber structures other than phen

18、olic and aminoplastic - Test methods - Part 1: Static load test of single bondline specimens in compression shear; prEN 15416-2, Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 2: Static load test of multiple bondline specimens in compression s

19、hear; prEN 15416-3, Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with speciments loaded in bending shear; and two test methods to characterize the working properties of the adhesive: EN

20、15416-4, Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods- Part 4: Determination of open assembly time for one component polyurethane adhesives; EN 15416-5, Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test method

21、s - Part 5: Determination of conventional pressing time. Requirements for the adhesives are stated in other standards, for instance requirements for one component polyurethane adhesives for load bearing timber structures are given in prEN 15425. According to the CEN/CENELEC Internal Regulations, the

22、 national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Polan

23、d, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 4 SAFETY STATEMENT Persons using this document should be familiar with the normal laboratory practic

24、e, in principle. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. Licensed Copy: Wang Bin, na, Mon

25、Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 5 1 Scope This document specifies a method of determining the conventional pressing time at three temperatures and three wood moisture contents. This document is intended to determine the conventional pressing time for one

26、 component polyurethane adhesives using a defined procedure for obtaining a reliable base for comparison of conventional pressing time between adhesives. The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence of factors

27、 such as timber density/moisture content, factory temperature and relative air humidity. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition

28、of the referenced document (including any amendments) applies. EN 302-1:2004, Adhesives for load bearing timber structures - Test methods - Part 1: Determination of bond strength in longitudinal tensile shear strength EN 923:2005, Adhesives Terms and definitions ISO 5893, Rubber and plastics test eq

29、uipment Tensile, flexural and compression types (constant rate of traverse) Specification 3 Terms and definitions For the purposes of this document, the definitions given in EN 923:2005 and the following apply. 3.1 conventional pressing time shortest pressing time (expressed as the mean of 10 indivi

30、dual results) that gives tensile shear strength of at least 4 N/mm at a given temperature and wood moisture content with the test procedure being that described in this standard. 4 Principle Standard beech lap joints are tested in tensile shear after various curing times until it is found that a she

31、ar strength of at least 4 N/mm is achieved at a given temperature and wood moisture content. 5 Apparatus 5.1 Climate cabinets Climatic cabinet capable of maintaining a temperature of (20 2) C and a relative humidity of (50 5) %, (65 5) % or (75 5) % to enable conditioning of the beech panels to a wo

32、od moisture content of 9 %, 12 % or 15 % respectively. Temperature cabinets capable of maintaining air temperature of (15 2) C, (20 2) C and (30 2) C respectively. Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 6 NOTE It is important to

33、 test at these temperatures although EN 386 specifies a higher temperature during the curing of structural adhesives. 5.2 Testing machine The testing machine shall be either: a) constant rate of loading machine capable of maintaining a rate of loading of (2,0 0,5) kN/min; or, b) constant rate of tra

34、verse machine as described in ISO 5893. The jaws of the testing machine shall grip the test pieces with a wedge action, ensure self-aligning of the test piece and prevent from slippage during loading. 6 Procedure Sufficient beech panels shall be prepared in accordance with EN 302-1:2004, clause 6.1

35、to enable 15 sets each of at least 10 test specimens with (0,3 0,1) mm glue lines to be manufactured. After conditioning three sets to (12 1) %, one set to (9 1) % and one set to (15 1) % wood moisture content in the climate cabinet, the panels with (12 1) % shall be divided into 3 equal groups one

36、for each of the 3 test temperature given in Table 1 and all the five groups shall be wrapped airtight to prevent further change in their moisture content. Each group of the panels shall be transferred to an atmosphere at one of the test temperatures described in Table 1. The adhesive to be used shal

37、l also be stored under these three temperatures respectively. Table 1 Examples of pressing time and nominal climatic conditions Wood moisture content (%) Temperature (C) Pressing time (h) 9 20 1 2 4 12 15 1 2 4 12 20 1 2 4 12 30 1 2 3 15 20 1 2 3 After at least 12 h conditioning at the test temperat

38、ure, the panels shall be glued and pressed. The test pieces shall not be removed from the test temperature during the pressing periods. Unless otherwise stated by the manufacturer, the clamping pressure shall be 0,8 N/mm. Table 1 gives the pressing time for each pair of panels. Immediately after the

39、 pressing time has elapsed, the panels shall be unclamped and 10 test specimens cut from each of the bonded panels according to EN 302-1:2004, clause 6.2. They shall be tested according to EN 302-1:2004, clause 6.5 without delay. Test values obviously influenced by factors like lack of adhesive or l

40、ocal defects in the wood shall be discarded. The conventional pressing time shall be calculated by linear interpolation of those pressing times and their related tensile shear strength that are most near to the time corresponding to a tensile shear strength of 4 N /mm. The tensile shear strength at

41、the shortest pressing time for each temperature and moisture content shall be less than 4 N/mm. If recommended by the adhesive manufacturer, shorter or longer pressing times Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 7 than those gi

42、ven in Table 1 can be used. The calculated conventional pressing time shall be expressed to the nearest 15 min rounded off to the next higher value. EXAMPLE A pressing time of 2 h gives a mean tensile strength of 2 N/mm, while the mean tensile shear strength for 4 h pressing time is 5 N/mm. The resu

43、lt of the linear interpolation for 4 N/mm is 3 h 20 min. This calculated value would be rounded off to 3 h 30 min. 7 Expression of results Calculate the shear strength of every test piece according to the following formula: aFs = Where s is the shear strength in Newton per square millimetre (N/mm2)

44、F is the load at failure in Newton (N) a is the area of the tested surface (200 mm2) Express the result of the test as the mean of the shear strength N/mm of the valid tests and the coefficient of variation of each test series. Express the wood failure as a mean of the valid test results. 8 Test rep

45、ort The following information about preparation of test pieces and testing procedure shall be included in the test report: a) statement that the tests were carried out in accordance with this standard. b) date on which the tests were carried out and the date of the report. c) chemical nature and ori

46、gin of the sample of adhesive tested. d) manufacturers name and batch number or other means of uniquely identifying the sample. e) details of the preparation and method of application of the adhesive including date of gluing. f) density of the wood in kg/m3at 12 % moisture content. g) temperature, p

47、ressure and duration of pressure used to produce the test joints. h) average glue line thickness measured on 2 samples from each test set. i) minimum, maximum, mean, standard deviation and coefficient of variation of the measurements taken in each series of tests. j) individual results from each tes

48、t piece. Failing stresses should be expressed to the nearest 0,1 N/mm2. Where appropriate the percentage of the fracture surface covered with wood fibre should be estimated to the nearest 10 %. Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006

49、 (E) 8 k) type of failure of each test piece (within the adhesive, in the wood or at the wood/adhesive interface). Licensed Copy: Wang Bin, na, Mon Nov 06 07:11:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSIEN 15416-5:2006 (E) 9 Bibliography 1 prEN 15425, Adhesives - One component polyurethane, for load bearing timber structures Classification and performance requirements 2 EN 386, Glued laminated timber Performance requirements and minimum production requirements Licensed Copy: Wang Bin, na, Mon Nov 06 07:1