EN 14836-2005 en Synthetic surfaces for outdoor sports areas - Exposure to artificial weathering (Incorporating corrigendum February 2007)《户外运动场合成地面 暴露于人工气候中 合并勘误表-2007年2月》.pdf

《EN 14836-2005 en Synthetic surfaces for outdoor sports areas - Exposure to artificial weathering (Incorporating corrigendum February 2007)《户外运动场合成地面 暴露于人工气候中 合并勘误表-2007年2月》.pdf》由会员分享，可在线阅读，更多相关《EN 14836-2005 en Synthetic surfaces for outdoor sports areas - Exposure to artificial weathering (Incorporating corrigendum February 2007)《户外运动场合成地面 暴露于人工气候中 合并勘误表-2007年2月》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 14836:2005Incorporating corrigendum no. 1Synthetic surfaces for outdoor sports areas Exposure to artificial weatheringThe European Standard EN 14836:2005 has the status of a British StandardICS 97.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g

2、48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 14836:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2007ISBN 0 580 48780 6National forew

3、ordThis British Standard was published by BSI. It is the UK implementation of EN 14836:2005, incorporating corrigendum February 2007. It partially supersedes BS 7044-2.4:1989 (replacing method 4). EN 14836:2005 is one of a package of standards being produced by CEN/TC 217. On publication of the enti

4、re package, BS 7044 will be withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/57, Surfaces for sports areas.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the

5、necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date Comments17066Corrigendum No. 129 June 2007 Change to Clause 5EUROPEAN STANDARDNORME

6、EUROPENNEEUROPISCHE NORMEN 14836December 2005ICS 97.220.10 Incorporating corrigendum February 2007English VersionSynthetic surfaces for outdoor sports areas - Exposure toartificial weatheringSurfaces synthtiques pour terrains de sport en plein air -Mthodes dessai - Vieillissement artificielSynthetis

7、che Sportbden fr den Auenbereich -Knstliche BewitterungThis European Standard was approved by CEN on 28 November 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without an

8、y alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by t

9、ranslationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, H

10、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de S

11、tassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14836:2005: EEN 14836:2005 (E) 2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Principle.4 4 Apparatus 4 5 Exposure conditions.5 6 Spe

12、cimens.5 7 Procedure 5 EN 14836:2005 (E) 3 Foreword This European Standard (EN 14836:2005) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publ

13、ication of an identical text or by endorsement, at the latest by June 2006, and conflicting national standards shall be withdrawn at the latest by June 2006. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this

14、 European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14836

15、:2005 (E) 4 1 Scope This European Standard specifies a method for the exposure of synthetic surfaces for outdoor sports areas to artificial weathering in order that the resulting changes in properties can be determined as detailed in the relevant product specification. 2 Normative references The fol

16、lowing referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 4892-1:2000, Plastics Methods of exposur

17、e to laboratory light sources Part 1: General guidance (ISO 4892-1:1999) EN ISO 4892-2:1999, Plastics Methods of exposure to laboratory light sources Part 2: Xenon-arc sources (ISO 4892-2:1994) EN ISO 4892-3, Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps (ISO

18、4892-3:1994) 3 Principle Specimens are exposed to UV radiation under controlled environmental conditions. NOTE Fluorescent UV lamps use the emission from a low-pressure mercury arc to excite a phosphor that produces a continuous spectrum in a relatively narrow wavelength interval, which is generally

19、 distributed about a peak wavelength. The spectral distribution of the radiation from a fluorescent lamp is determined by the emission spectrum of the phosphor and the UV transmission properties of the glass tube. Fluorescent UV lamps are generally used to expose material to UV radiation in a limite

20、d spectral range. 4 Apparatus Artificial weathering cabinet using fluorescent UV lamps and environmental control having the following features. a) UV-A 340 nm lamps, in accordance with EN ISO 4892-3 and capable of uniformly applying radiation to the test specimen at an irradiance of 0,80 W/(m2/nm) (

21、at 340 nm). NOTE 1 As many fluorescent lamps age significantly with extended use, the apparatus manufacturers instructions on the procedure necessary to maintain the desired irradiance should be followed. NOTE 2 The use of UV-B fluorescent UV lamps or exposure in a xenon arc artificial weathering ca

22、binet is recommended when developing or assessing products intended for installation in environments where high levels of UV exposure might be expected. b) Exposure chamber, constructed from inert material and that provides uniform irradiance in accordance with item a) and that includes a means of c

23、ontrolling the temperature. c) Wetting mechanism, either condensation or water spray, to wet the exposed face of the specimen. In apparatus designed to wet the exposed faces of the specimens by means of a humidity-condensing mechanism, the water vapour shall be generated by heating water in a contai

24、ner located beneath and extending across the whole area occupied by the specimens. Specimen holders (completely filled with specimens) shall constitute the sidewall of the exposure chamber, so that the backs of the specimens are EN 14836:2005 (E) 5 exposed to the cooling effect of the ambient room a

25、ir. If wetting is provided by spraying the specimens, the water shall conform to EN ISO 4892-2:1999, 4.6. d) Radiometer, conforming to EN ISO 4892-1:2000, 5.1.7, to monitor irradiance and radiant exposure. e) Black-panel thermometer, conforming to EN ISO 4892-1:2000, 5.2.2. f) Specimen holders, made

26、 from inert materials that will not affect the results of the exposure. The holders shall be mounted so that the exposed face of the specimen is located in accordance with the manufacturers instructions, and shall be no more than 50 mm from the UV lamp bank plane. 5 Exposure conditions 6 Specimens S

27、pecimens shall be of the size specified by the test methods for the properties to be measured after exposure, as detailed in the relevant product specification. 7 Procedure Mount the specimen without strain in the specimen holders with the test surface facing the lamps. Fill any spaces, using blank

28、panels, to ensure uniform exposure conditions. Expose the specimen, measuring the irradiance and radiant exposure at the surface of the specimen. After an exposure of (4 896 125) kJ, carefully remove the specimen from the exposure cabinet and test as required by the product specification. NOTE An ex

29、posure of (4 896 125) kJ will require approximately 2 000h UV exposure and takes approximately 3 000 h with cycling to complete. The exposure cycle shall comprise (240 4) min of dry UV exposure at a black-standard temperature of (55 3) C, followed by (120 2) min of condensation exposure, commencing

30、once equilibrium has been attained, without radiation, at a black-standard temperature of (45 3) C.BS EN 14836:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standa

31、rds in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of o

32、ur products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996

33、 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996

34、 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise reques

35、ted.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services.

36、Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Members

37、hip Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyrigh

38、t subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or

39、 by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.